Pioneer-VSXC301-avr-sm 电路图 维修手册.pdf

《Pioneer-VSXC301-avr-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Pioneer-VSXC301-avr-sm 电路图 维修手册.pdf（108页珍藏版）》请在收音机爱好者资料库上搜索。

1、 ORDER NO. PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01

2、, Singapore 159936 PIONEER CORPORATION 2003 AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-C301 SOUND MODEINPUT SELECTORMASTERVOLUMEPHONESADVANCEDSTEREOAV DIRECT FRONT INPUT STANDBY/ON DIGITAL INPHONES VIDEOAUDIO RL DTS2PRO LOGICII2DIGITAL DOWNUP R VSX-C301-S RRV2741 AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-C

3、301-S VSX-C301-K THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). ModelTypePower RequirementRemarks VSX-C301-SMYXUAC220-230V VSX-C301-KMYXUAC220-230V VSX-C301-SNVXUAC230V For details, refer to Important symbols for good services. T-ZZK APR. 2003 printed in Japan RadioFans.CN 收音机爱 好者资

4、料库 VSX-C301-S2 1234 1234 C D F A B E SAFETY INFORMATION This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex p

5、roducts such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the r

6、epair to a qualified service technician. WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health other functions control other external equipment. 19 Numbe

7、r buttons Use for numerical input of track numbers, radio frequencies, and so on. 20 CHANNEL +/ Use to change channels on a satellite receiver, cable box, VCR or DVR. 21 TV CONTROL buttons Use to control your TV (after setting up the remote control to work with your TV). Clearing preset codes This r

8、estores all presets to the factory defaults. See Using the remote control with other components for the default remote settings. Press RECEIVER and number button 0 (zero) at the same time. Keep them pressed for about 3 seconds. The LED on the remote control blinks three times indicating all the pres

9、et codes have been cleared. The default preset codes are shown in the table. Input/control mode select button Preset code Component (manufacturer) DVD020DVD (Pioneer) STB200STB (Pioneer) DVR/TV459DVD recorder (Pioneer) VIDEO600TV (Pioneer) FRONT100LD (Pioneer) FM/AMn/a(built-in tuner) TV CONTROL600T

10、V (Pioneer) VSX-C301-S108 1234 1234 C D F A B E Default receiver settings The table below shows the factory default settings. When you reset the system, the receiver reverts to these defaults. The default settings for the remote control to control other components can be found in Using the remote co

11、ntrol with other components. Setting typeDefault setting InputDVD Master volume dB (no sound) Listening modeAUTO (all inputs) Listening mode (w/ headphones) STEREO (all inputs) Sound modeOFF DialogOFF Virtual Surround BackOFF Input signal selectAUTO Speakers (Front, Center, Surround) Setting Automat

12、ically sensed Subwoofer setting200 Hz LFE Attenuator0 dB Front speaker distance 2.0 m Center speaker distance 2.0 m Surround speaker distance 2.0 m Dynamic Range Control OFF Dual Monoch1 Input AttenuatorOFF (all inputs) DVD(STB) COAX jack assignment DVD STB(DVD) OPT1 jack assignment STB Setting the

13、volume level of each channel Front: 0 dB Center: 0 dB Surround: 0 dB Subwoofer: 0 dB AV Direct settingMANUAL Auto Input Select setting MANUAL Room SetupM / MID Resetting the system Use this feature to reset the system to its factory default settings. 1Press RECEIVER. 2In standby, press ROOM SETUP an

14、d SYSTEM SETUP at the same time. The display prompts you to confirm. 3Within 5 seconds, press LEVEL . The display shows OK. 4Within 5 seconds, press LEVEL +. The receiver should now be reset. If the receiver is disconnected from the power outlet for more than a month it will reset to the default set

15、tings. The above reset doesnt affect the presets that you have programmed into the remote control (see Using the remote control with other components). SOURCERECEIVER SLEEP RECEIVER AV DIRECT INPUT DVD VIDEO STB FRONTFM/AM DVR/TV SURROUND ADV ANCED SURROUND SOUND MODE SIGNAL SELECTDIALOG AU TOSTEREO LEVELTEST TONECH SELECT MUTE MASTER VOL UME DT V MENU T OP MENU T .EDIT MENU ROOM SETUP TUNE STST SYSTEM SETUP ENTER