Philips-AZT-3202-Service-Manual(1) 电路图 维修手册.pdf

《Philips-AZT-3202-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-AZT-3202-Service-Manual(1) 电路图 维修手册.pdf（36页珍藏版）》请在收音机爱好者资料库上搜索。

1、PRODUCT FAMILY TARGET FM TUNER Technical specification .1- 1 Features and Accessories.1- 2 Connections and controls.1- 3.1- 4 Instruction For Use.1- 5.1- 10 Safety , 9 .- switches the player on, starts or pauses CD play - stops CD play, clears a program or switches the player off 9 TUNING , TUNER :

2、- (down,up) tunes to radio station; CD : - skips and searches CD tracks forwards or backwards. 0 RESUME.stores the last position of a CD track played HOLD.locks all buttons OFF.switches RESUME and HOLD off ! LINE OUT/p.3.5 mm headphone jack and LINE OUT jack to connect the player to another audio in

3、put of an additional appliance. VOL E .adjusts the volume # 4.5V DC.jack for external power supply $ .belt clip holder % .type plate POWER SUPPLY / GENERAL INFORMATION Mains adapter (supplied or optionally available) Use only the AYT 3170 adapter (4.5 V / 300 mA direct current, positive pole to the

4、center pin). Any other product may damage the player. 1 Make sure the local voltage corresponds to the power adapters voltage. 2 Connect the power adapter to the 4.5V DC jack of the player and to the wall outlet. Note: Always disconnect the adapter when you are not using it. Environmental informatio

5、n All redundant packing material has been omitted. We have done our utmost to make the packaging easily separable into two materials: cardboard (box) and polyethylene (bags, protective foam sheet). Your set consists of materials which can be recycled if disassembled by a specialized company. Please

6、observe the local regulations regarding the disposal of packing materials, dead batteries and old equipment. CONNECTIONS AND CONTROLS 1- 5 CD player and CD handling Do not touch the lens A of the CD player. Do not expose the unit, batteries or CDs to humidity, rain, sand or excessive heat (caused by

7、 heating equipment or direct sunlight). You can clean the CD player with a soft, slightly dampened, lint-free cloth. Do not use any cleaning agents as they may have a corrosive effect. To clean the CD, wipe it in a straight line from the center toward the edge using a soft, lint-free cloth. A cleani

8、ng agent may damage the disc! Never write on a CD or attach a sticker to it. The lens may cloud over when the unit is moved suddenly from cold to warm surroundings. Playing a CD is not possible then. Leave the CD player in a warm environment until the moisture has evaporated. Active mobile phones in

9、 the vicinity of the CD player may cause malfunctions. Avoid dropping the unit as this may cause damage. Headphones HS383 Connect the supplied headphones to the LINE OUT/p jack of the player. Note:LINE OUT/pcan also be used for connecting this set to your HiFi system.To adjust the sound and volume,

10、use the controls on the connected audio equipment and on the CD player. IMPORTANT! Hearing safety: Do not play your headphones at a high volume. Hearing experts advise that continuous use at high volume can permanently damage your hearing. Traffi c safety: Do not use headphones while driving a vehic

11、le. It may create a hazard and it is illegal in many countries. Even if your headphones are an open-air type designed to let you hear outside sounds, do not turn up the volume so high that you cannot hear what is going on around you. Batteries (supplied or optionally available) You can use the follo

12、wing batteries with this CD-player: normal batteries type LR6, UM3 or AA (preferably Philips), or alkaline batteries type LR6, UM3 or AA (preferably Philips). Notes: Old and new or different types of batteries should not be combined. Remove batteries if they are empty or if the player is not going t

13、o be used for a long time. Inserting batteries 1 Push OPEN 2 to open the CD lid. 2 Open the battery compartment and insert either 2 normal or alkaline batteries. Battery indication The approximate power level of your batteries is shown in the display. Battery full Battery two-thirds full Battery one

14、-third full Battery dead or empty. When the batteries are dead or empty, the symbol fl ashes, bAtt is displayed, and the beep tone sounds repeatedly. Average playing time of batteries under normal conditions Battery typeESP onPower Save Normal5 hours6 hours Alkaline16 hours20 hours Batteries contain

15、 chemical substances, so they should be disposed of properly. INSTRUCTION FOR USE 1- 6 GENERAL INFORMATION / CD PLAY In-car use (connections supplied or optionally available) Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 118 71890) car voltage converter (4.5 V DC, positive pole to the cente

16、r pin) and the AY 3501 cassette car adapter. Any other product may damage the set. 1Put the set on a horizontal, vibration-free and stable surface. Make sure it is in a safe place, where the set is neither a danger nor an obstacle to the driver and the passengers. 2Plug the voltage converter into th

17、e cigarette lighter jack (only for 12 V car battery, negative grounding), then connect the wired end with 4.5V DC input jack on the set. 3If necessary, clean the cigarette lighter jack to obtain a good electrical con- tact. 4Turn down the volume and connect the cassette adapter plug to LINE OUT/p on

18、 the set. 5Carefully insert the cassette adapter into the car radios cassette compartment. 6Make sure the cord does not hinder your driving. 7Decrease the volume on the set if necessary. Start playback on the set and adjust the sound with the car radio controls. Always remove the voltage converter f

19、rom the cigarette lighter jack- when the set is not in use. Note: If your car radio has a LINE IN jack, it is better to use it for the car radio connection instead of the cassette.adapter. Connect the signal lead to this LINE IN jack and to LINE OUT/pon the set. CD PLAY / FEATURES Playback informati

20、on If a CD-Recordable (CD-R) or a CD-Rewritable (CD-RW) is not recorded properly, nF dISC is displayed, indicating that the CD has not been fi nalized. In that case, use FINALIZE on your CD recorder to complete the recording. When playing a CD-Rewritable (CD-RW), please note that it takes 315 second

21、s after pressing 2; for sound reproduction to start. Playback will stop if you open the CD lid. While the CD is read, 1 -:- fl ashes in the display. Volume and bass Volume adjustment Adjust the volume by using VOL E. Bass adjustment Press DBB to switch the bass enhancement on or off yis shown if the

22、 bass enhancement is activated. DBB INSTRUCTION FOR USE 1 - 7 Selecting a track and searching Selecting a track during playback Briefl y press or once or several times to skip to the current, previous or next track. yPlayback continues with the selected track, and the tracks number is displayed. Sel

23、ecting a track when playback is stopped 1 Briefl y press or once or several times to select the desired track. The track number is displayed. 2 Press 2; to start CD play. yPlayback starts with the selected track. Searching for a passage during playback 1 Keep or pressed to fi nd a particular passage

24、 in a backward or forward direction. ySearching starts while playback continues at low volume. After 2 seconds the search speeds up. 2 Release the button when you reach the desired passage. yPlayback continues from this position. Notes: If the player is in SCAN mode (see MODE chapter), searching is

25、not possible. Playing a CD This CD-player can play all kinds of Audio Discs such as CD-Recordables and CD-Rewritables. Do not try to play a CD-ROM, CDi, VCD, DVD or computer CD. 1 Push the OPEN 2 slider to open the player. 2 Insert an audio CD, printed side up, by pressing the CD onto the hub. 3 Clo

26、se the player by pressing the lid down. 4 Press 2; to switch the player on and start playback. yThe current track number and elapsed playing time are displayed. You can pause playback by pressing 2;. yThe time at which playback was paused starts fl ashing. You can continue playback by pressing 2; ag

27、ain. 5 Press 9 to stop playback. yThe total number of tracks and the total playing time of the CD are displayed. 6 Press 9 again to switch the player off. To remove the CD, hold it by its edge and press the hub gently while lifting the CD. Note: If there is no activity, the set will automatically sw

28、itch off after a while to save energy. INSTRUCTION FOR USE 1 - 8 FEATURES Programming track numbers You can store up to 30 tracks to play in a program. A single track may be stored more than once in the program. 1 While playback is stopped, select a track with or . 2 Press PROG to store the track. y

29、programlights up; the track number programmed and P with the total number of stored tracks are displayed. 3 Select and store all desired tracks in this way. 4 Press 2; to start playback of your selected tracks. yprogramis shown and playback starts. You can review the program by pressing PROG for mor

30、e than 2 seconds. yThe display shows all the stored tracks in sequence. Notes: If you press PROGand there is no track selected, SELis displayed. If you try to store more than 30 tracks, FULLis displayed. Clearing the program While playback is stopped, press 9 to clear program. yCLR is displayed once

31、, programgoes off, and the program is cleared. Note:The program will also be cleared if the power supply is interrupted, or if the CD-player lid is opened, or if the set switches off automatically. FEATURES RESUME and HOLD You can interrupt playback and continue (even after an extended period of tim

32、e) from the position where playback stopped (RESUME) and you can lock all buttons of the set so that no action will be executed (HOLD). Use the RESUMEHOLDOFF slider for these functions. RESUME continuing from where you have stopped 1 Switch the slider to RESUME during playback to activate RESUME. yr

33、esumeis shown. 2 Press 9 whenever you want to stop playback. 3 Press 2; whenever you want to resume playback. yresumeis shown and playback continues from where you have stopped. To deactivate RESUME, switch the slider to OFF. yresumegoes off. HOLD locking all buttons You can lock the buttons of the

34、set by switching the slider to HOLD. Now, when a key is pressed, no action will be executed. This is of use, for example, when transporting the player in a bag. With HOLD activated, you can avoid accidental activation of other functions. 1 Switch the slider to HOLD to activate HOLD. yAll buttons are

35、 locked. HoLd is shown when you press any button. If the set is switched off, holdwill be shown only when 2; or FM is pressed. 2 To deactivate HOLD, switch the slider to OFF. Note: If you deactivate HOLDby switching the slider to RESUME, you will be activating the RESUMEfunction. INSTRUCTION FOR USE

36、 1 - 9 Selecting different playing possibilities MODE It is possible to play tracks in random order, to repeat a single track or the entire CD, and to play the fi rst few seconds of each track. 1 Press MODE during playback as often as required in order to activate one of the following modes. The act

37、ive mode is shown in the display. y shuffl e:All tracks of the CD are played in random order until all of them have been played once. y shuffl e repeat all :All tracks of the CD are played repeatedly in random order. yrepeat:The current track is played repeatedly. yrepeat all:The entire CD is played

38、 repeatedly. ySCAN: The fi rst 10 seconds of each of the remain- ing tracks are played in sequence. 2 Playback starts in the chosen mode after 2 seconds. To return to normal playback, press MODE repeatedly until the display shows no active modes. ESP / Power Save Mode With a conventional portable CD

39、-player you might have experienced that the music stopped e.g. when you were jogging. The ELECTRONIC SKIP PROTECTION prevents loss of sound caused by light vibrations and shocks. Continuous playback is ensured. However ESP does not prevent playback interruptions during vigorous running. It also does

40、 not protect the unit against any damage caused by dropping! On this set ESP is default on. It is possible to set ESP off and enter the Power Save mode. The Power Save mode helps to extend battery lifetime for longer playback. Press MODE for more than 2 seconds. ydisappears. power save modeis now ac

41、tivated. Press MODE again for more than 2 seconds. yis displayed once Radio Play You can tune to any FM station automatically or manually. 1 Press FM to switch the radio on. Tuning to radio stations automatically 1 Keep or pressed for at least 2 second. yThe radio tunes to a station with suffi cient

42、 strength and radio play starts. The current waveband and frequency are displayed. 2 Repeat searching until you fi nd the desired radio station. Tuning to radio stations manually 1 Keep or pressed. 2 Release or , then briefl y press or again when you are close to the desired frequency. 3 Briefl y pr

43、ess or repeatedly until you reach the desired frequency. yRadio play starts. The current waveband and frequency are displayed. To switch from radio play to CD play, press 2; . Press FM or 9 to switch the radio off. INSTRUCTION FOR USE 1 - 10 Troubleshooting WARNING: Under no circumstances should you

44、 try to repair the set yourself as this will invalidate the warranty. If a fault occurs, fi rst check the points listed, before taking the unit for repair. If you are unable to solve a problem by following these hints, consult your dealer or service center. The CD player has no power, or playback do

45、es not start Check that your batteries are not dead or empty, that they are inserted correctly, that the contact pins are clean. Your adapter connection may be loose. Connect it securely. For in-car use,check that the car ignition is on. Also check players batteries. The indication no diSC is displa

46、yed Check that the CD is clean and correctly inserted (label-side upward). If your lens has steamed up, wait a few minutes for this to clear. The indication nF diSC is displayed CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder. The indicationHOLDis on and/or there is no react

47、ion to controls If HOLD is activated, then deactivate it. Electrostatic discharge. Disconnect power or remove batteries for a few seconds. The CD skips tracks The CD is damaged or dirty. Replace or clean the CD. RESUME, SHUFFLE or PROGRAM is active. Switch off whichever is on. No sound or bad sound

48、quality. PAUSE might be active. Press 2;. Loose, wrong or dirty connections. Check and clean connections. Volume might not be appropriately adjusted. Adjust the volume. Strong magnetic fi elds. Check players position and connections. Also keep away from active mobile phones. For in-car use,check that the cassette adapter is inserted correctly, that the car cassette players playback direction is correct (press autoreverse to change), and that the cigarette lighter jack i