Philips-DVD-612-Service-Manual(1) 电路图 维修手册.pdf

《Philips-DVD-612-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-DVD-612-Service-Manual(1) 电路图 维修手册.pdf（44页珍藏版）》请在收音机爱好者资料库上搜索。

1、Published by MW 0162 Service PaCEPrinted in the NetherlandsSubject to modification? 3122 785 11090 Copyright 2001 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form

2、 or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. DVD-Video PlayerDVD612 DVD612 /001/021/051 CL 16532007_000.eps 30-01-01 ContentsPage 1Technical specifications and connection facilities2 2Warnings, laser safety instructions and notes3 3Dir

3、ections for use6 4Mechanical instructions and exploded views16 5Diagnostic software descriptions and troubleshooting21 6Block- and wiring diagram Blockdiagram39 Wiring diagram40 7Electrical diagrams and print-layoutsDiagram PWB Power supply4142-43 A/V Board Video control(Diagram A1)4446-47 A/V Board

4、 Audio(Diagram A2)4546-47 Display panel(Diagram D)4849 Bare board Standby5050 8Electrical alignments51 9Circuit descriptions and51 List of abbreviations54 10 Spare part list55 RTV servis Horvat Tel: +385-31-856-637 Tel/fax: +385-31-856-139 Mob: 098-788-319 www.rtv-horvat-dj.hr ? RadioFans.CN 收音机爱 好者

5、资料库 Technical specificationsGB 2DVD612 /XX11. 1.Technical specifications English Specification PLAYBACK SYSTEM DVD-Video Video CD no other equipment is needed to perform a number of hardware tests to check if the DVD player is faulty. The diagnosis is simply a error or pass message; no indication is

6、 given of faulty hardware modules. Only tests within the scope of the diagnostic software will be executed hence only faults within this scope can be detected. 5.1.2Contents of Dealer Script The dealer script executes all diagnostic nuclei that do not need any user interaction and are meaningful on

7、a standalone DVD player. The nuclei called in the dealer script are the following (the number after each nucleus name corresponds with the number being on the local display when the nucleus is executed during the dealer script): Figure 5-1 Figure 5-2 CL06532096_001.eps 050700 NucleusDescription Vide

8、oColSetupComm7Checks the I2C interface with the RGB video processor on the Audio/Video board (only for DVD players with RGB video processor). PapChksFl6Calculate and verify checksum of FLASH memory. PapI2cDisp5Checks the I2C interface with the slave processor on the display PCB. PapS2bEcho4Checks th

9、e I2C interface to the basic engine. PapI2cNvram3Checks the I2C interface with the NVRAM. PapNvramWrR2Pattern test of all locations in the NVRAM CompSdramWrR1Pattern test of all locations in the SDRAM(s). Press 2 keys simultaneously + Connect to mains. During the test, the following display is shown

10、: the counter counts down from the number of nuclei to be run before the test finishes. Example: SET O.K.? YES NO To exit DEALER SCRIPT ,disconnect from mains. CL 96532065_004.eps 120799 ? Diagnostic software descriptions and troubleshootingGB 22DVD612 /XX15. 5.2PLAYER SCRIPT 5.2.1Purpose of Player

11、Script The Player script will give the opportunity to perform a test that will determine which of the DVD players modules are faulty, to read the error log and error bits and to perform an endurance loop test. To successfully perform the tests, the DVD player must be connected to a tv set to check t

12、he output of a number of nuclei. For DVDv2b a multi-channel amplifier, a set of 6 boxes and an external video source are necessary to test. To be able to check results of certain nuclei, the player script expects some interaction of the user (i.e. to approve a test picture or a test sound). Some nuc

13、lei (e.g. nuclei that test functionality of the Basic Engine module) require that the DVD player itself is opened, to enable the user to observe moving parts and approve their movement visually. Only tests within the scope of the diagnostic software will be executed hence only faults within this sco

14、pe can be detected. 5.2.2Contents of Player Script The player script contains all nuclei that are useful on a DVD player that is connected to a tv-set and help to determine which module of the DVD player is faulty, as well as to read out the contents of the error logs. 5.2.3Structure of Player Scrip

15、t The player script consists of a set of nuclei testing the three hardware modules in the DVD player: the Display PWB, the Digital PWB and the Basic Engine. Nuclei run by the player test need some user interaction; in the next paragraph this interaction is described. The player test is done in two p

16、hases: 1.Interactive tests: this part of the player test depends strongly on user interaction and input to determine nucleus results and to progress through the full test. Reading the error log and error bits information can be useful to determine any errors that occurred recently during normal oper

17、ation of the DVD player. 2.The loop test will loop through the list of nuclei indefinitely, till the NEXT key is pressed. The list of nuclei is as follows: VideoColSetupComm VideoScartSwComm PapChksFlash PapI2cNvram CompSdramWrR PapS2bEcho PapI2cDisp For DSW version 1.6 and above. the DSW version nu

18、mber will be displayed on the local display. Press NEXT to continue to the display test. The display should look like the following: Figure 5-3 5.2.4Survey Figure 5-4 CL 16532007_002.eps 010201 SLEDGE TEST BeSledgeOut/In(41ab) FOCUS TEST BeFocusOn(38a) DISC MOTOR TEST BeDiscMotorOn(39a) RADIAL TEST

19、BeRadialOn(40a) JUMP TEST BeGroovesIn/Mid/Out(42abc) Press 2 keys simultaneously + Connect to mains To exit player test, disconnect from mains INTERACTIVE TESTS DISPLAY TEST DispDisplay(30) LED TEST DispLed(29) KEYBOARD TEST DispKeyb(27) SCART LOOP TEST AudioPinkNoiseOn(20a) VideoScartSwDvd(54a) Vid

20、eoColDencOn(23a) PICTURE TEST DISPLAY PCB MONO PCB(SERVO) if it is, press PLAY, if it is not, press PAUSE. By pressing NEXT the script will proceed to the next test. If the user presses NEXT before PLAY or PAUSE, the DispLed nucleus will return TRUE (LED test successful). Figure 5-5 5.3.3KEYBOARD TE

21、ST The keyboard of the DVD player is tested by nucleus DispKeyb. The user is expected to press all keys on the local keyboard once. The code of the key pressed is shown on the local display (1 hexadecimal digit) immediately followed by a (hexadecimal) number indicating how many times that key has be

22、en pressed. Example of the local display during this test: Figure 5-6 The key-codes displayed on the local display will scroll from right to left when the display gets full, the text tb- will remain on display. Figure 5-7 If any keys are detected more than once (due to hardware error), the key-code

23、is displayed twice (or more), with the second digit increased by 1. If the user does not press all keys minimally once (in any order), the DispKeys nucleus will return FALSE and cause an error in the overall result of the player script. The test will also pass if all buttons, except the microphone k

24、ey buttons, are pressed. The user can leave the keyboard test by pressing the NEXT key on the local display of the DVD player for at least one full second. The result of the keyboard test is shown on local display as follows: Figure 5-8 Or Figure 5-9 Pressing NEXT on the local keyboard again will pr

25、oceed to the next text. 5.3.4REMOTE CONTROL TEST The remote control of the DVD player is tested by nucleus DispRc. The user must press any key on the remote control just once. The codes of the key pressed will be shown on the local display in hexadecimal format. Example: Figure 5-10 In this example

26、23 is the hexidecimal code of the pressed RC key. The user can leave the remote-control test by pressing NEXT on the local keyboard of the DVD player. The remote If OK, press PLAYIf NOK, press PAUSE If OK, press PLAYIf NOK, press PAUSE If OK, press PLAYIf NOK, press PAUSE press NEXT to continue CL 9

27、6532065_006.eps 120799 CL 96532065_007.eps 120799 key id.key 0PLAY 1NEXT 2PREVIOUS 3PAUSE 4STOP 5 OPEN/CLOSE 6 3D-SURROUND 7KEY- (Mic Control) 8 Once More (Mic Control) 9 KEY+(Mic Control) A STAND BY CL16532007_007.eps 300101 CL 96532065_009.eps 120799 CL 96532065_010.eps 120799 CL 96532065_011.eps

28、120799 ? Diagnostic software descriptions and troubleshootingGB 24DVD612 /XX15. control test is successful if a code was received before the user pressed the NEXT key; pressing the NEXT key before pressing a key on the remote control gives an error in the remote control test (note that the remote co

29、ntrol test will also fail if a key on the remote control was pressed but no code was received). The remote control test does not check upon the contents of the received code, that is it will not be checked if the received code matches the key pressed. If desired, the user can manually check this cod

30、e by using a code-table for the remote control key-codes. Figure 5-11 After pressing NEXT, the result of the remote control test is displayed on the local display of the DVD player as follows: Figure 5-12 Or Figure 5-13 Pressing NEXT on the local keyboard again will proceed to the next test. 5.3.5P5

31、0 LOOP-BACK TEST For the P50 loop-back test, the user must first press a key to decide if the test is to be performed. The display will show the following message: Figure 5-14 If the user presses PAUSE, the P50 test will be skipped. If the user presses PLAY, the P50 test is performed and the result

32、is displayed as follows: Test successfull: Figure 5-15 Test fails: Figure 5-16 Press the NEXT key to continue to the next text 5.4MONO PCB DIGITAL PART 5.4.1PICTURE TEST The picture test is performed by putting a predefined picture (colour bar) on the display (nucleus VideoColDencOn) and CL06532096_

33、003.eps 050700 C Key idHexadecimal code STANDBY0C STOP31 PLAY2C PLAY BACKWARD2D PAUSE30 STEP FORWARDF6 STEP BACKWARDF5 FORWARD28 FORWARD 4XDF FORWARD 8XE0 BACKWARD29 BACKWARD 4XDE BACKWARD 8XDD SLOW22 SLOW 2D9 SLOW BACKWARD23 SLOW BACKWARD 2DA NEXT20 PREVIOUS21 CURSOR UP58 CURSOR DOWN59 CURSOR LEFT5

34、A CURSOR RIGHT5B OK5C 00 11 22 33 44 55 66 77 88 99 TOGGLEC8 ANGLE85 AUDIO4E SUBTITLES4B SUBTITLE ON/OFFE3 ROOT MENU54 TITLE MENU71 MENUD1 SETUP MENU82 OSD ON/OFFF RETURN83 RESUMED7 SCAN2A SHUFFLE1C REPEAT1D A/B REPEAT3B TOGGLE SCART43 OPEN/CLOSE42 FTSFB KARAOKEE4 OPTIONFA CL 96532065_013.eps 120799

35、 CL 96532065_014.eps 120799 CL 16532007_004.eps 010201 CL 16532007_005.eps 010201 CL 16532007_006.eps 010201 ? Diagnostic software descriptions and troubleshootingGB 25DVD612 /XX15. asking the user for confirmation. The display will show the following message: Figure 5-17 By pressing PLAY the user c

36、onfirms the test, pressing PAUSE will indicate the picture was invisible or incorrect. Pressing NEXT will proceed to the next test 5.4.2SOUND 1 the display will show the following message very shortly: Figure 5-18 This sound will only be audible from version cut3.1 of Sti5505(item7503 on mono board)

37、 onwards. After starting up sound 1, SCART loop-trough will be simultaneously active during this test. SCART loop-trough will be measured with the aid of an external video source. When entering the SCART loop-trough, the local display indicates: Figure 5-19 On the TV screen a colour bar (generated b

38、y nucleus VideoColDencOn) is visual and the internally generated pinknoise is audible. By pressing PLAY the user confirms the test, pressing PAUSE will indicate the sound was inaudible or incorrect. Pressing NEXT will proceed to the next test; if the user presses NEXT without pressing PLAY or PAUSE

39、first, the result of this test will be TRUE (sound ok). By pressing the NEXT button there will be switched over to the external source, this must become now visible on the TV screen (using the SCART). The local display indicates: Figure 5-20 The internally generated colour bar is still available on

40、the CVBS and Y/C outputs. And the pinknoise-signal is still available on the cinch audio outputs. By pressing the PREV button, the internal generated colour bar becomes visual again. The test can be left by pressing the NEXT key for more than one second. 5.4.3SOUND 2 TEST The second soundtest is per

41、formed by producing a sine sound (nucleus AudioSineOn). The signal can be stopped by pressing the STOP-key. The display will show the following message: Figure 5-21 By pressing PLAY the user confirms the test, pressing PAUSE will indicate that something went wrong. Pressing NEXT will proceed to the

42、next; if the user presses NEXT without pressing PLAY or PAUSE first, the result of this test will be TRUE (sound ok). 5.4.4Colour setup test The colour setup test is performed by putting the internally generated colour bar in different settings on the TV screen. The first colour bar will be displaye

43、d in setting 1. the display will show the following message: Figure 5-22 By pressing the NEXT button, you can go to the second setting. The local display indicates: Figure 5-23 By pressing the PREVIOUS button, the colour bar with the first setting becomes visual again. By pressing PLAY the user conf

44、irms the test, pressing PAUSE will indicate that something went wrong. The test can be left by pressing the NEXT key for more than one second; if the user presses NEXT without pressing PLAY or PAUSE first, the result of the test will be TRUE )colour set- up ok). 5.5BASIC ENGINE 5.5.1VERSION NUMBER I

45、n the basic engine tests, the version number of the Basic Engine will be shown first, as the following example: CL 96532065_015.eps 120799 CL 96532065_016.eps 120799 CL 96532065_017.eps 120799 CL 96532065_018.eps 120799 CL 96532065_019.eps 120799 CL06532096_004.eps 050700 CL06532096_005.eps 050700 ?

46、 Diagnostic software descriptions and troubleshootingGB 26DVD612 /XX15. Figure 5-24 By pressing the NEXT key, the Basic Engine tests are started. 5.5.2TRAY TEST First, the tray is tested. The purpose of this test is also to give the user the opportunity to put a disc in the tray of the DVD player. S

47、ome tests on the Basic Engine require that a disc(e.g. DVD MPTD test disc) is present in the player. At the end of the Basic Engine tests this tray test will be repeated solely to enable the user to remove the disc in the tray. The local display will look as follows: Figure 5-25 By pressing PLAY or

48、PAUSE the user can toggle the position of the tray. Note that this test will not contribute to the test result of the Basic Engine. Pressing NEXT will proceed to the next test, after the tray has been closed (by the software) if it was open. 5.5.3SLEDGE TEST(visual test) The second Basic Engine test

49、 tests the sledge; the user can move the sledge as many times as desired by using PLAY (nucleus BeSledgeOut) and PAUSE (nucleus BeSledgeIn). Pressing NEXT on the local keyboard proceeds to the next test. Note that this test will not contribute to the test result of the Basic Engine. The local display will look as follows during the sledge test: Figure 5-26 5.5.4DISC MOTOR TEST(visual test) The third Basic Engine test tests the disc