Philips-HTS-3580-Service-Manual(1) 电路图 维修手册.pdf

《Philips-HTS-3580-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-HTS-3580-Service-Manual(1) 电路图 维修手册.pdf（50页珍藏版）》请在收音机爱好者资料库上搜索。

1、1 1 HTS3580/12/93 Copyright 2010 Philips Consumer Electronics B.V. Eindhoven, The Netherlands All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the p

2、rior permission of Philips. Published by RY HY1107 Service Audio Printed in The Netherlands Subject to modification BD Home Theater System Version 1.2 TABLE OF CONTENTS Location of PCB Boards . 1-2 Versions Variation . 1-2 Measurement Setup . 1-4 Specifications . 1-3 Service Aids . 1-5 ESD GREEN FOR

3、 /98) Playback media BD-Video, DVD-Video, DVD+R/+RW,DVD-R/-RW, DVD+R/- R DL, CD-R/CDRW,Audio CD, Video CD/SVCD, PictureCD, MP3-CD, WMA-CD, DivX (Ultra)-CD, USB fl ash drive. File Format Audio .mp3, .wma Video . .avi, .divx, .mkv, .wmv Picture .jpg, .gif, .png Amplifier Total output power .1000 W RMS

4、 (30%THD) Frequency response .20 Hz-20 kHz /3dB Signal-to-noise ratio. . 65 dB (CCIR) /(A-weighted) Input sensitivity: AUX . 500 mV MP3 LINK .250 mV Video Signal system . PAL / NTSC HDMI output .480i/576i, 480p/576p,720p, 1080i, 1080p Audio Sampling frequency: MP3 . 32 kHz, 44.1 kHz, 48 kHz WMA .44.

5、1 kHz, 48 kHz Constant bit rate: MP3 .112 kbps - 320 kbps WMA .48 kbps - 192 kbps Radio Tuning range .FM 87.5-108 MHz (50 kHz) Signal-to-noise ratio .FM 55 dB Frequency response .FM 180 Hz-12.5 kHz/ 3dB USB Compatibility .Hi-Speed USB (2.0) Class support . UMS (USB Mass Storage Class) File system .

6、FAT16, FAT32, NTFS Maximum memory support . 160GB Main Unit Power supply .220-240V; 50-60 Hz Power supply .220-230V; 50-60 Hz Power supply .110-127V/220-240V; 50-60 Hz Power consumption .100 W Standby power consumption . 0.9 W Dimensions (WxHxD) . 360 x 58 x 351(mm) Weight .3.22 kg Speakers Speaker

7、impedance . 4 ohm (center), 4ohm (Front/Rear) Speaker drivers .1 x 3” full range Frequency response .150 Hz-20 kHz Dimensions (WxHxD): Center . 161 x 92 x 95 (mm) Speaker . 95 x 161 x 87 (mm) Tall speaker . 254 x 1001 x 254 (mm) Weight: Center . 0.77 kg Speaker .0.56 kg/each Tall speaker .3.38 kg/ea

8、ch Cable length: Center . 3 m Front . 4 m Rear . 10 m Subwoofer Impedance . 4 ohm Speaker drivers .165 mm (6.5”) woofer Frequency response . 40 Hz-150 Hz Dimensions (WxHxD) . 123 x 369 x 309(mm) Weight .3.81 kg Cable length . 4 m Laser specification Laser Type (Diode) .InGaN/AIGaN (BD) .InGaAIP (DVD

9、), A IGaAs (CD) Wave length .405 +5nm/-5nm (BD) .650+13nm/-10nm (DVD) .790 +15nm/-15nm(CD) Output power (Max. ratings) .20mW(BD), 7mW (DVD/CD) Specifi cations subject to change without prior notice. RadioFans.CN 收音机爱 好者资料库 1 - 4 LEVEL METER e.g. Sennheiser UPM550 with FF-filter S/N and distortion me

10、ter e.g. Sound Technology ST1700B L R DUT CD Use Audio Signal Disc (replaces test disc 3) SBC429 4822 397 30184 Bandpass 250Hz-15kHz e.g. 7122 707 48001 LF Voltmeter e.g. PM2534 DUT RF Generator e.g. PM5326 S/N and distortion meter e.g. Sound Technology ST1700B Use a bandpass filter to eliminate hum

11、 (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz). R =50 Tuner FM MEASUREMENT SETUP 1 - 5 Service Tools: Universal Torx driver holder .4822 395 91019 Torx bit T10 150mm .4822 395 50456 Torx driver set T6 T20 .4822 395 50145 Torx driver T10 extended .4822 395 50423 Compact Disc: SBC426

12、/426A Test disc 5 + 5A .4822 397 30096 SBC442 Audio Burn in test disc 1kHz .4822 397 30155 SBC429 Audio Signals disc .4822 397 30184 Dolby Pro logic Test Disc .4822 395 10216 SERVICE AIDS HANDLING CHIP COMPONENTS 1 - 6 NLWAARSCHUWING Alle ICs en vele andere halfgeleiders zijn gevoelig voor electrost

13、atische ontladingen (ESD). Onzorgvuldig behandelen tijdens reparatie kan de levensduur drastisch doen verminderen. Zorg ervoor dat u tijdens reparatie via een polsband met weerstand verbonden bent met hetzelfde potentiaal als de massa van het apparaat. Houd componenten en hulpmiddelen ook op ditzelf

14、de potentiaal. IAVVERTIMENTO Tutti IC e parecchi semi conduttori sono sensibili alle scariche statiche (ESD). La loro longevit potrebbe essere fortemente ridatta in caso di non osservazione della pi grande cauzione alla loro manipolazione. Durante le riparazioni occorre quindi essere collegato allo

15、stesso potenziale che quello della massa dellapparecchio tramite un braccialetto a resistenza. Assicurarsi che i componenti e anche gli utensili con quali si lavora siano anche a questo potenziale. GB Safety regulations require that the set be restored to its original condition and that parts which

16、are identical with those specified, be used. Safety components are marked by the symbol ! . NL Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen, identiek aan de gespecificeerde, worden toegepast. De Veiligheidsonder

17、delen zijn aangeduid met het symbol ! . F Les normes de scurit exigent que lappareil soit remis ltat dorigine et que soient utiliss les pices de rechange identiques celles spcifies. Less composants de scurit sont marqus ! . D Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu beachten

18、. Der Original zustand des Gerts darf nicht verndert werden; fr Reparaturen sind Original Ersatzteile zu verwenden. Sicherheitsbauteile sind durch das Symbol ! markiert. I Le norme di sicurezza esigono che lapparecchio venga rimesso nelle condizioni originali e che siano utilizzati i pezzi di ricamb

19、io identici a quelli specificati. Componenty di sicurezza sono marcati con ! . GB After servicing and before returning set to customer perform a leakage current measurement test from all exposed metal parts to earth ground to assure no shock hazard exist, The leakage current must not exceed 0.5mA. C

20、LASS 1 LASER PRODUCT 3122 110 03420 GBWarning ! Invisible laser radiation when open. Avoid direct exposure to beam. SVarning ! Osynlig laserstrlning nr apparaten r ppnad och sprren r urkopplad. Betrakta ej strlen. SFVaroitus ! Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina nkymttm

21、lle laseristeilylle. l katso steeseen! GBWARNING All ICs and many other semi conductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can reduce life drastically. When repairing, make sure that you are connected with the same potential as the mass of the set via

22、a wrist wrap with resistance. Keep components and tools also at this potential. F ATTENTION Tous les IC et beaucoup dautres semi conducteurs sont sensibles aux dcharges statiques (ESD). Leur longvit pourrait tre considrablement courte par le fait quaucune prcaution nest prise leur manipulation. Lors

23、 de rparations, sassurer de bien tre reli au mme potentiel que la masse de lappareil et enfiler le bracelet serti dune rsistance de scurit. Veiller ce que les composants ainsi que les outils que lon utilise soient galement ce potentiel. ESD DWARNUNG Alle ICs und viele andere Halbleiter sind empfindl

24、ich gegenber elektrostatischen Entladungen (ESD). Unsorgfltige Behandlung im Reparaturfall kan die Lebensdauer drastisch reduzieren. Veranlassen Sie, dass Sie im Reparaturfall ber ein Pulsarmband mit Widerstand verbunden sind mit dem gleichen Potential wie die Masse des Gertes. Bauteile und Hilfsmit

25、tel auch auf dieses gleiche Potential halten. DKAdvarse ! Usynlig laserstrling ved bning nr sikkerhedsafbrydere er ude af funktion. Undg udsaettelse for strling. F Pour votre scurit, ces documents doivent tre utiliss par des spcialistes agrs, seuls habilits rparer votre appareil en panne. GB ESD PRO

26、TECTION EQUIPMENT Complete Kit ESD3 (small tablemat, wristband, connection box, estention cable and earth cable .4822 310 10671 Wristband tester . 4822 344 13999 1 - 7 Pb(Lead) Free Solder When soldering , be sure to use the pb free solder. INDENTIFICATION: Regardless of special logo (not always ind

27、icated) onemusttreatallsetsfrom1 Jan2005onwards,according next rules: Important note: In fact also products of year 2004 must be treatedin this way as long as youavoidmixingsolder- alloys(leaded/ lead-free). Sobest to always use SAC305 and the higher temperatures belong to this. Due to lead-free tec

28、hnology some rules have to be respected by the workshop during a repair: Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment. In general use of solder-paste withinworkshopsshoul

29、dbeavoidedbecausepaste is not easy to store and to handle. Use only adequate solder tools applicable for lead- free solder alloy. The solder tool must be able To reach at least a solder-temperature of 400?C, To stabilize theadjustedtemperature atthesolder- tip To exchange solder-tips for different a

30、pplications. Adjust your solder tool so that a temperature around 360?C 380?C is reachedandstabilized at thesolder joint.Heating-timeofthesolder-jointshould notexceed 4 sec. Avoid temperatures above 400?C otherwise wear-out of tips will rise drastically and flux-fluid will be destroyed. To avoid wea

31、r-out of tips switch off un- used equipment, or reduce heat. Mix of lead-free solder alloy / parts with leaded solder alloy / parts is possible but PHILIPS recommends strongly to avoidmixed solderalloy types (leadedand lead-free). Ifonecannot avoidordoes not knowwhetherproduct is lead-free, clean ca

32、refully the solder-joint from old solder alloy and re-solder with new solder alloy (SAC305). Use only original spare-parts listed in the Service- Manuals. Not listed standard-material (commodities) has to be purchased at external companies. Special information for BGA-ICs: Always use the 12nc-recogn

33、izable soldering temperature profile of the specific BGA (for de- solderingalwaysuse thelead-free temperatureprofile, in case of doubt) Lead free BGA-ICs will be delivered in so-called dry- packaging(sealedpack including a silica gelpack) to protect the IC against moisture. After opening, dependent

34、of MSL-level seenonindicator-labelin the bag, the BGA-IC possibly still has to be baked dry. (MSL=Moisture Sensitivity Level). This will be communicated via AYS-website. Do not re-use BGAs at all. For sets produced before 1.1.2005 (except products of 2004), containing leaded solder-alloy and compone

35、nts, all needed spare-parts will be available till the end of the service-period. For repair of such sets nothing changes. On our websitewww.atyourservice.ce.P you find more information to: BGA-de-/soldering (+ baking instructions) Heating-profiles of BGAs and other ICs used in Philips-sets You will

36、 find this and more technical information within the “magazine”, chapter “workshop news”. For additional questions please contact your local repair-helpdesk. 2 - 12 - 1 Setting procedure & Repair instruction 1)Restore factory setting a) Press “” button on R/C. b) Select , then press “OK” button on R

37、/C. c) Select ,then press button on R/C. d) Select ,then press to confirm. 2)Password change a) Press “” button on R/C. b) Select , then press “OK” button on R/C. c) Select , then press button on R/C. d) Select , then press button on R/C. “0000” is default password supplied. 3)Trade mode a) In open

38、model,press “” button on R/C. b) Press “2” “5” “9” on R/C,VFD will display “TRA ON” or “TRA OFF”. 4)Check software version a) Press “” button on R/C b) Select , then press button on R/C. c) Select ,then press button on R/C. d) TV will show message as follow: Model:HTS3560/12/51/98/93 Version: System

39、 SW:29.00 Subsystem SW:28-00-00-00 Ethernet MAC:00-25-D1-02-25-D4 Close e) Select on the version display screen and press button to exit . 5) Upgrading new software Method 1: Update software from a USB storage device or CD-R a) Create a folder named “UPG” in your CD-R or USB storage device, and Copy the latest upgrading software into the folder. b) Insert the CD-R program disc or connect the USB