Philips-AZ-5155-Service-Manual(1) 电路图 维修手册.pdf

《Philips-AZ-5155-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-AZ-5155-Service-Manual(1) 电路图 维修手册.pdf（32页珍藏版）》请在收音机爱好者资料库上搜索。

1、Handling Chip Components and Safety .1 - 1 Technical Specification - to interrupt recording or playback. STOPOPEN 9 / - To stop the tape and to open the cassette holder. SEARCH 5 or 6 - to fast wind/rewind the tape. PLAY 1 - to start playback. RECORD 0 - to start recording. 7REMOTE SENSOR - infrared

2、 sensor for remote control 8 Cassette compartment CD PLAYER : 9CD/VCD Display - to show the CD/VCD/MP3- CD functions and disc status. 0 PLAY/PAUSE 2; - To start or interrupt CD/VCD/MP3-CDplayback. STOP 9 - to stop CD/VCD/MP3-CD playback. CD MODE - to select a different play mode e.g. SHUFFLE/REPEAT.

3、 SEARCH or - to skip or search a passage or a track. ! OPEN - to open / close the CD door. RADIO: TUNING - to tune to radio stations. # Tuning dial pointer $ AUDIO / VIDEO SOCKET - to connect to a TV set. % Battery door - to open the battery compartment. Telescopic aerial - to improve FM reception.

4、- to start or interrupt playback. * SEARCH 5 or 6 (for CD/VCD/MP3-CD) - to search back or forward. ( ALBUM for MP3-CD only . . . . to select previous / next album ) TRACK for MP3-CD only . . . . to select previous/next title. for CD/VCD . . . . . . . . to search backward/ forward track. STOP 9 - to

5、stop playback or to clear a programme. KEY+ / KEY- - to change the VCD key tone to suit to your vocal range. ECHO + / ECHO - - to adjust the VCD echo level for karaoke after you inserted a microphone. REWFWD MX / SEL 4 3 - 3 This set can play all digital audio CD, video CD, finalised digital audio C

6、D-Recordable (CDR) discs and finalised digital audio CD-Rewritable (CDRW) discs. Support following MP3-CD formats: ISO 9660 or ISO 9660 + Joliet format - Max. 30 characters Max. Track number is 400 Max. nested directory is 8 levels The max. album number is 99 The max. MP3 programme track number is 2

7、0 The max. length of each track is 99 minutes 59 seconds The player can play mixed mode disc of CD / MP3-CD Supported VBR bit-rate Supported sampling frequencies for MP3 disc : 8 kHz to 48 kHz (44.1kHz preferably) Supported bit-rates of MP3 disc are: 32 - 320 kbps (128 kbps preferably) Following for

8、mats are not supported The files like *.WMA, *AAC, *.DLF, *.M3U, *.PLS, MP3 PRO The non-session closed discs 1. Set the source selector to CD/VCD. 2. Lift to open the CD door. OP will be displayed 3. Insert a disc with the label side facing up. 4. Close the CD door. The total number of tracks of the

9、 disc appear on the display. no will be displayed if no disc is inserted or error in CD operation For MP3-CD only The total track number XXX and album number “AXX will be displayed interchangeably. LOADING A DISC DISCS FOR PLAYBACK CD/VCD/MP3-CD CAUTION Use of controls or adjustments or performance

10、of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. Environmental information All unnecessary packaging material has been omitted. We have done our utmost to make the packaging easily separable into three mono materials: cardboard, polystyrene and pl

11、astic. Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. INSTRUCTIONS FOR USE GENERAL OPERATION 1. Check if the mains voltage as sho

12、wn on the type plate (on the bottom of the set) corresponds to your local mains voltage. Select 110 or 220V by the selector (for some version only). 2. If your set is equipped with a voltage selector, adjust the selector so that it matches with the local mains. 3. Connect the mains lead to the AC MA

13、INS socket and the wall socket. The set is now ready for use. 4. To switch off the mains supply completely, pull the mains plug out of the wall socket. Disconnect the mains lead when you change over to battery supply, or to protect the set during heavy thunderstorms. The type plate is located on the

14、 bottom of the set. 1. To switch on the set, adjust the source selector. 2. Adjust the sound using the VOLUME, DYNAMIC BASS BOOST and INCREDIBLE SURROUND control buttons. 3 To switch off the set, adjust the source selector to the TAPE/OFF position, with the cassette keys released. 1 Set the source s

15、elector to FM or MW. 2. Adjust the sound using the VOLUME, DYNAMIC BASS BOOST and INCREDIBLE SURROUND control buttons. 3. Tune to a radio station using the TUNING knob. For FM, pull out the telescopic aerial. To improve FM-reception, incline and turn the aerial. Reduce its length if the FM-signal is

16、 too strong (very close to a transmitter). For MW, the set is provided with a built-in aerial, so the telescopic aerial is not needed. Direct the aerial by turning the whole set. 4. To switch off, set the source selector to the TAPE/OFF position (with the cassette keys released). RADIO RECEPTION SEA

17、RCH VOLUM INCREDIBL SURRO ULTRA B DYNAMIC BASS PLAYPAUSE RECORD PLAY SEARCH STOP-OPEN PAUSE GENERAL OPERATION MAINS SEARCH VOLUME INCREDIBLE SURROUND ULTRA BASS DYNAMIC BASS BOOST TUNING PLAYPAUSE STOP CD MODE RECORD PLAY SEARCH STOP-OPEN PAUSE 108 104 100 96 92 88 FMMHz 1600 1300 1000 800 630 530 M

18、WMHz SEARCH VOLUME INCREDIBLE SURROUND ULTRA BASS DYNAMIC BASS BOOST TUNING PLAYPAUSE STOP CD MODE RECORD PLAY SEARCH STOP-OPEN PAUSE 108 104 100 96 92 88 FMMHz 1600 1300 1000 800 630 530 MWMHz 3 - 4 CD/VCD/MP3-CD Programming tracks of disc is possible when playback is stopped. Up to 20 tracks can b

19、e stored in the memory in any order. 1. In stop mode, press PROG on the remote control to enter programme setting. PROG will flash on the display. 2. Press digits 0 - 9 on the remote control or / to select the desired track. 3. Press PROG to store the select track. The number “XXX” represents the tr

20、ack no. Repeat steps 1 to 3 to store other tracks. 4. Press 9 to end programme setting. PROG will remain on the display. Press PROG (on remote control) in stop mode to review the programme sequence. 5. Press2;to play the programmed tracks. If you press REPEAT during programme playback, the current t

21、rack or all programmed tracks will be played repeatedly. REPEAT/REPEAT ALL icon and PROG will appear on the display. 6. Press 9 in stop mode to clear the programme. PROG will disappear from the display. Notes : -The programming is automatically cleared as soon as the CD compartment is opened. - The

22、function of programme setting is disabled in PLAY/PAUSE mode. - Programme cannot be used for VCDs when PBC is switched on. Switch off PBC before storing tracks from such a VCD. For MP3-CD only 1. In stop mode, press PROGon the remote control to enter programme setting. PROGwill start flashing and P0

23、1 will be displayed. On TV screen, PROG program list (5 lines per page) will be displayed. 2. Press digits 0 - 9 on the remote control or /to select the desired album. 3. PressPROGto store the select album. The number “AXX” represents the album no. 4. Press / repeatedly (or digits 0 - 9 on the remot

24、e control) to select the desired TRACK for programming. 5. PressPROGto store the select track. PROG will remain on the display. Repeat steps 1 to 5 to store other desired album and track. 6. Press 9 to end programme setting. PressPROGin stop mode can review the programme sequence. 7. Press 2 to star

25、t programme playback. You can press / to select the programmed track to play. 8. Press 9 once stop programme playback or twice to clear the programme. PROGRAMMING TRACKS INSTRUCTIONS FOR USE CD/VCD/MP3-CD On TV screen, the total ALBUM and TRACK number will display, also with the album list (max. 10

26、lines per page). The current selected music is highlighted. Notes : - To ensure good system performance, wait until the disc completely reads before proceeding. - For MP3-CD, the disc reading time may exceed 1 minute due to the large number of songs compiled into one disc. 1. Press2;to start playbac

27、k. The track number of the current track and 2appear on the display. To interrupt playback, press 2;. 2will disappear and the current track number will start flashing. To resume playback, press 2;again. 2. To stop playback, press 9. To select a desired track Press or on the set repeatedly (or use di

28、gits 0 - 9 buttons on the remote control) until the desired track appears on the display. If playback is stopped, press 2;to start playback. To search for a particular passage during playback Press and hold or on the set for 1 second (or on the remote control,press5 or 6) During searching, the volum

29、e will be muted. For MP3-CD only To select a desired album On the remote control, press or until the desired album number appear on the display. AXX will be displayed. On TV screen, the arrow will move forward/backward in the ALBUM menu. To select a desired track Press or on the set repeatedly (or o

30、n the remote control, press or ) to select a desired track from the current album. XXX will be displayed. On TV screen, the arrow will move forward/backward in the TRACK menu. Use the digital keys on the remote control to select the track under current album directly. To select and playback another

31、track during playback mode 1. Press or repeatedly to select another track. The new selected track will show on the display screen and TV screen and playback continuously. 2. Press2;to start playback the new selected track. For VCD only Either press5or6on the remote control repeatedly to select fast

32、search speed (x1, x2, x3 or x4) or press to have a still picture on the TV screen. The sound will be muted. On TV screen, PAUSE will be displayed. 2. Press2;again to continue playback. Goto 1. Press GOTO on the remote control. On TV screen, GOTO -:- will be displayed. 2. Press digits 0 - 9 on the re

33、mote control to key in the disc time which you want the disc to begin playback. Note : - The disc time entered should not be greater than the total disc time. - Goto mode is not available whenever PBC mode is switched on. Slow 1. Press SLOW on the remote control to watch a VCD at a slower speed. The

34、re are 4 types of slow modes to select. The sound will be muted. On TV screen, SLOW 1/2, SLOW 1/4, SLOW 1/8 or SLOW 1/16 will be displayed. 2. To resume playback at normal speed, press SLOW repeatedly until PLAY appears on the TV screen or press 2;. A-B repeat This feature is also applicable to audi

35、o CD (except for MP3-CD). To Play a certain scene or passage of the disc repeatedly. VIDEO CD INSTRUCTIONS FOR USE CD/VCD/MP3-CD You can play all the tracks in random order. 1. During playing, pause or stop mode, press SHUFFLE on the remote control or press CD MODE on the set to enable SHUFFLE play

36、mode. SHUFFLE will appear on the display. 2. To exit shuffle mode, press SHUFFLE again or 9. SHUFFLE will disappear from the display. You can play the current track or the whole disc repeatedly. 1. During CD/ MP3-CD playing or pause mode, press REPEAT on the remote control or CD MODE on the set. REP

37、EAT icon - to repeat the current track. REPEAT ALL icon all- to repeat the whole disc. 2. To exit the repeat mode, press REPEAT on the remote control or CD MODE on the set until the REPEAT/REPEAT ALL icon disappears from the display. Notes : - If the Repeat function is enable, and the Stop button is

38、 pressed, will disable all the repeat play modes. Adjusting the TV System Before viewing the Video CD, ensure that the set is switched to corresponding PAL or NTSC system of your TV set (exception Multi - system TV). 1. On the remote control, press NTSC/PAL to switch between NTSC and PAL TV system.

39、OSD - On Screen Display If you insert VCD/CD, your TV screen will serve as an additional display for messages (e.g. PLAY, STOP), and information stored on the VCD/CD. Press OSD on the remote control to select viewing various information. The current track and current /elapsed time in the track/disc

40、appear on the display. VIDEO CD REPEAT SHUFFLE 3 - 6 CD/VCD/MP3-CD This set can play a mixed mode disc. mixture of audio CD and MP3-CD mixture of other combination may not be operated normally. 1. As default, audio CD tracks will be read first. will be displayed. TV screen, MIX, CD-DA will be displa

41、yed. 2. PressMIX/SEL(on the remote control) repeatedly to select other disc modes. MP3-CD: MP3 is displayed. TV screen, MP3 menu is displayed. Notes : - For protected CDs, “MIX CD-DA” is displayed on your TV screen even if the disc does not have other format. The MIX/SELnormal functions are not avai

42、lable for protected CDs. PLAYING A MIXED MODE DISC INSTRUCTIONS FOR USE CD/VCD/MP3-CD 1.Press A-B on the remote control during playback to mark the start point of the chosen scene or passage. REPEAT A will appear on the screen. 2. Press A-B again to mark the end of the chosen scene or passage. REPEA

43、T AB will appear on the screen. The selected scene or passage will start playing repeatedly. 3. Press A-B once more to return to normal playback. REPEAT AB will disappear from the display. Notes : - You can also cancel A-B repeat by pressing or . - A-B repeat marking can cross from one track to anot

44、her. But for VCD 2.0, you are only able to set the A-B repeat marking within the same track. Resume In stop mode, press RESUME on the remote control to start playback again from where you have stopped. Note : - Resume will not be available if you have changed the disc, opened the disc tray or discon

45、nected the system from the power supply. View This feature allows you to scan through a VCD for a quick review. PBC mode must be switched off. 1. In stop mode, press VIEW on the remote control to go to disc view function. On TV screen, up to 9 pictures will be displayed. If a menu consists of more t

46、han one page, press or to view the previous/next page. The first several seconds of each track will be played. To exit review mode, press digits 0 - 9 to play the desired track or 2;to play the current selected track. 2. In playback mode, press VIEW on the remote control to go to track view function

47、. press or to select the track. On TV screen, up to 9 pictures within the track will be displayed. The first several seconds of each picture will be played. To exit review mode, press digits 0 - 9 to play the desired position within the track or 2;to play the current selected position. Note : - If t

48、he disc is AVCD disc and therere no video tracks on the same viewed page, cannot use the direct digital key to play the track. Return Press RETURN on the remote control to return to the previous VCD disc MENU level. It is functional only for Video CD when PBC is switched on. R/L/ST You can use it to

49、 select the different audio modes. Press R/L/ST on the remote control repeatedly to select the following modes: on the LCD represents channel left/channel right / dual channel on a bilingual VCD or mono left / mono right / stereo on single language VCD. 3 - 7 CASSETTE RECORDER 1. Set the source selector to FM or MW. 2. Tune to the desired radio station using the TUNING knob. 3. PressSTOPOPEN 9 /to open the cassette holder. 4. Insert a blank tape. 5. Press RECORD 0 to start recording. 6. For brief interruptions, press P