Philips-DVDR-3360-H-Service-Manual(1) 电路图 维修手册.pdf

《Philips-DVDR-3360-H-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-DVDR-3360-H-Service-Manual(1) 电路图 维修手册.pdf（14页珍藏版）》请在收音机爱好者资料库上搜索。

1、Published by KC-TE 0617 AV Systems Printed in the Netherlands Subject to modifi cation EN 3139 785 32060 DVDR3360HHDD & DVD Recorder Service Instruction CLASS 1 LASER PRODUCT Contents Page 1 Technical Specifi cations and Connection Facilities 2 2 Test Disc & Repair Hints 5 3 Firmware Upgrading 6 4 S

2、ervice Flow chart 7 5 Directions For Use 12 Copyright 2006 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,

3、 or otherwise without the prior permission of Philips. Version 1.0 DVDR3360H/05/31/51/58 The 2006 range DVD Recorder products are repaired centrally. Defective sets must be identifi ed, labelled and stored for pick-up. This document gives full instructions for a functional check. Technical informati

4、on to repair faulty sets is therefore not provided in this document. To test in-coming sets the following must be performed: 1. Verify / Reproduce the customers problem 2. Verify that set has latest Firmware (see chapter 3) and upgrade if it is not the latest version. 3. Full functional check RadioF

5、ans.CN 收音机爱 好者资料库 EN 23139 785 320601. Technical Specifi cations and Connection Facilities 1. Technical Specifi cations and Connection Facilities 1.1 General: Mains voltage : 220V 240V Mains frequency : 50 Hz Power consumption (record) : 27 W Standby Power Consumption : 3 W 1.2 RF Tuner Test equipme

6、nt: Fluke 54200 TV Signal generator Test streams: PAL BG Philips Standard test pattern 1.2.1 System PAL B/G, PAL D/K, SECAM L/L, PAL I 1.2.2 RF - Loop Through: Frequency range : 43 MHz 860 MHz Gain: (ANT IN - ANT OUT) w/o Amplifi er : -4dB 2dB Gain: (ANT IN - ANT OUT) with Amplifi er : 2dB 3dB 1.2.3

7、 Receiver: PLL tuning with AFC for optimum reception Frequency range : 45.25 MHz 857 MHz Sensitivity at 40dB S/N (video unweighted) : 40dBV at 75 (high end) 60dBV at 75 (low end) 1.2.4 Video Performance: Channel 25 / 503,25 MHz, Test pattern: PAL BG PHILIPS standard test pattern, RF Level 74dBV, Mea

8、sured on SCART 1 Frequency response : 0.1 MHz 4 MHz 3dB Group delay (0.1 MHz - 4.4 MHz) : 0 nsec 150 nsec 1.2.5 Audio Performance: Audio Performance Analogue - HiFi: Frequency response at SCART 1 (L+R) output : 100 Hz 12 kHz / 0 3dB S/N Ratio (20Hz 20kHz) unweighted : 40dB Harmonic distortion (1 kHz

9、, 25 kHz deviation) : 1.5% Audio Performance NICAM: Frequency response at SCART 1 (L+R) output : 40 Hz 15 kHz / 0 3dB S/N Ratio (20Hz 20kHz) unweighted : 65dB Harmonic distortion (1kHz, 25 kHz deviation) : 0.5% 1.2.6 Tuning Automatic Search Tuning Scanning time without RF signal : 3min. typical Stop

10、 level (vision carrier) : 37dB/V Maximum tuning error of a recalled program : 62.5 kHz Maximum tuning error (drift) during operation : 100 kHz Tuning Principle: Automatic B, G, I, DK and L/L detection Manual selection in “STORE” mode 1.3 Analog Inputs / Outputs 1.3.1 SCART 1 (Connected to TV) Pin Si

11、gnals: 1 Audio-out R 1.8V RMS 2 Audio-in R 3 Audio-out L 1.8V RMS 4 Audio GND 5 Blue / Chroma GND 6 Audio-in L 7 Blue-out 0.7Vpp 0.1V into 75 8 Function switch 4.5V / 9.5V / 12V = asp. Ratio 4:3 DVD 9 Green GND 10 P50 control not use 11 Green out 0.7Vpp 0.1V into 75 12 NC 13 Red / Chroma GND 14 Fast

12、 switch GND 15 Red-out / 0.7Vpp 0.1V into 75 Chroma-out 300mVpp 3dB 16 Fast switch RGB / CVBS or Y out 1V / 10k Video - Cinch Input voltage : 1Vpp 3dB Input impedance : 75 Video - YC (Hosiden) According to IEC 933-5 Superimposed DC-level on pin 4 (load 100k) 3.5V is detected as 16:9 aspect ratio Inp

13、ut voltage Y : 1Vpp 3dB Input impedance Y : 75 Input voltage C : 300mVpp 3dB Input impedance C : 75 1.3.4 Out 1 Component Video Cinch Y/Pb/Pr according EIO-770-I-A, EIA-770-2 Audio - Cinch Output voltage : 2Vrms max. Output impedance : 10k 1.3.5 Out 2 Audio - Cinch Output voltage : 2Vrms max. Output

14、 impedance : 10k Video - Cinch Output voltage : 1Vpp 3dB Output impedance : 75 Video - YC (Hosiden) According to IEC 933-5 Superimposed DC-level on pin 4 (load 100k) 3.5V is detected as 16:9 aspect ratio Output voltage Y : 1Vpp 3dB Input impedance : 75 Output voltage C : 300mVpp 3dB Input impedance

15、: 75 1.4 Digital Inputs / Outputs 1.4.1 Digital Output Digital Audio Coaxial / Optical LCM : according IEC 60958 MPEG 1, MPEG 2, AC3 : according IEC 61937 DTS : according IEC 61937 + addendum 1.4.2 Digital Video Input (IEEE 1394) Implementation Standard according: IEEE Std 1394-1995 IEC61883 - Part1

16、 IEC61883 - Part 2 SD-DVCR (02-01-1997) Specifi cation of consumer use digital VCRs using 6.3mm magnetic tape dec.1994 Mechanical connection according to Annex of IEC 61883-1 1.5 Video Performance All outputs loaded with 75 SNR measurements over full bandwidth without weighting. 1.5.1 SCART (RGB) SN

17、R : 55dB on all output Bandwidth : 4.8MHz -3dB 1.6 Audio Performance 1.6.1 Cinch Output Rear Output voltage 2 channel mode : 2Vrms 1dB Channel unbalance (1kHz) : 110dB Crosstalk 16Hz-20kHz : 100dB Frequency response 20Hz-20kHz : 0.2dB Signal to noise ratio (unweighted) : -95dB Dynamic range 1kHz : -

18、90dB Distortion and noise 1kHz : 85dB Distortion and noise 16Hz-20kHz : 85dB Intermodulation distortion : -94dB Mute : -100dB 1.6.2 Scart Audio Output voltage 2 channel mode : 1.6Vrms 2dB Channel unbalance (1kHz) : 85dB Crosstalk 16Hz-20kHz : 70dB Frequency response 20Hz-20kHz : 0.5dB Signal to nois

19、e ratio (unweighted) : 80dB Dynamic range 1kHz : 75dB Distortion and noise 1kHz : 75dB Distortion and noise 16Hz-20kHz : 50dB Intermodulation distortion : 70dB Mute : 80dB 1.7 Dimensions and Weight Height of feet : 5.5mm Apparatus : WxDxH:435x322x43mm Weight without packaging : 3kg Weight with packa

20、ging : 4kg RadioFans.CN 收音机爱 好者资料库 EN 43139 785 320601. Technical Specifi cations and Connection Facilities 1.8 Laser Output Power & Wavelength 1.8.1 DVD Output power during reading : 0.8mW Output power during writing : 20mW Wavelength : 650nm 1.8.2 CD Output power : 0.3mW Wavelength : 780nm 1.9 Rea

21、d / Write Speed Type of Disc (Function)Disc Rotation Speed Read Speed CD7X CAV Read Speed DVD4X CAV Write Speed DVD+R/+RW2.4X ZCAV Write Speed DVD-R/-RW2X 1.10 Playability DVDR3360H Video Playback 1.Disc Media: CD-R/-RW, MP3- CD, VCD/SVCD, DVD-Video, DVD+R/+RW, DVD-R/-RW, DVD+RL DL x 2.Compression F

22、ormat: MPEG1, MPEG2 DivX 3.11, DivX 4.x, DivX 5.x, DivX 6.0 x Audio Playback 1.Disc Media: CD, CD-R/-RW, MP3-CD x 2.Compression Format: Dolby Digital, MP3, MPEG2 Multi- channel, AAC, WMA x 3.MP3 bit rates: 32- 256 kbps and VBR x Still Picture Playback 1.Disc Media: Picture CD x 2.Picture Compression

23、 Format: JPG x EN 53139 785 320602.Test Disc & Repair Hints 2. Test Disc & Repair Hints 2.1 Test Disc 1) 7104 099 96611 CD-RW printed Audio Disc 2) 9965 000 25728 DVD Player Test Pack 3) - Blank DVD+RW 4) - Blank DVD-RW 2.2 Open the DVD Tray manually Note: This procedure needs to be performed on con

24、dition that: - a customers Disc is jammed in the DVD Tray - the DVD Tray cannot be open via the normal open/close button on the set. 1) Place the set on the table with the bottom faced upwards as shown below. 2) Insert a screw driver into the slot and open the DVD Tray by sliding the screw driver in

25、 the direction shown. Figure 2-1 1 2 EN 63139 785 320603.Firmware Upgrading 3. Firmware Upgrading 3.1 Firmware Upgrading A. Preparation to upgrade fi rmware: 1. Unzip the zip-archive fi le 2. Start the CD Burning software and create a new CD project (data disc) with the following settings: File syst

26、em : Joliet Format : MODE 2: CDROM XA Recording mode : SINGLE SESSION (TRACK-AT-ONCE), FINALIZED CD Note: Long fi le name is necessary for the preparation of the upgrade disc 3. Place the content of the zip-archive into the root directory of the new CD project. 4. Burn the data onto a blank CDR or C

27、D-RW B. Procedure to apply the fi rmware upgrade: 1. Power up the set and press buttons down. 2. Close the tray and set will display: FLASH 1 3. The OSD Display. “Disc Upgrade - Software Upgrade Disc detected .Select OK to start upgrading or CANCEL to exit.” Press OK and the set will display: ERASE

28、WRITE.VERIFY The OSD Display “Software Upgrade.Please wait.Do not switch off the power.” The loader software will also upgrade.OSD display “Loader software Upgrade Upgrading software.Please wait.Do not switch off the power.” Note: When the screen display “Verify”, the progress bar stays at 80% for 5

29、 minutes and do not switch off the power ,or the set will be defective. The whole process takes less than 15 minutes Note: Do not press any buttons or interrupt the mains supply during the upgrading process, otherwise the set may becomes defective. 4. When the upgrade is completed the tray will open

30、 automatically and the set will display: “Loader upgrade process have completed successfully.Press OK to reboot system.” 5. The tray open and the set will display: DONE 6. Press OK and the set will go into Standby mode. C. How to read out the fi rmware version to confi rm set has been upgraded: 1. P

31、ower up the set.and ensure no disc in the disc tray. 2. Press button on the Remote control 3. Press in the proper sequence 4. Press and the screen will display Firmware Information Build 5019V07 010 / Date:12 Apr 2006 Loader Version 43.03.10 Macrovision Version: MPEG Chip ID: Audio DAC: Region Num:

32、2 Developer: Philips PS3360H_31_R19.07 5. Press button and to exit. EN 73139 785 320604.Service Flow Chart 4. Service Flow Chart 4.1 Start Process Start A (Verification Test) Is it a Hardware problem ? Upgrade to latest Firmware Is it a known complaint ? Is Firmware solution available ? Yes No Yes N

33、o Yes No Is the complaint solved ? Return set to Customer with Yes No Report on action done Send refurbished set from pool stock to Trade / customer Is the complaint documented ? Yes No Service W/S to contact the Trade / Customer to work out a action plan. Examples: - explain them that the Firmware

34、solution is not ready - Upgrade disc will be send to them the moment solution is ready - etc. - Attached a Defect Description Report and Proof of Purchase. - Pack defective set. - Store defective set for pick-up. EN 83139 785 320604.Service Flow Chart 4.2 Verifi cation Process * If complaint is rela

35、ted to Setup Menu setting Connect up the Recorder to TV antenna, TV set and an External source Check the Firmware version on the set Can the set Start-up ? Yes No A (Verification Test) B Recording Check C Playback Check D * Setup Menu Are the checks result ok ? Yes No Return set to Customer with Rep

36、ort on action done Send refurbished set from pool stock to Trade / customer - Attached a Defect Description Report and Proof of Purchase. - Pack defective set. - Store defective set for pick-up. No Yes Is Firmware the last released version ? Upgrade to latest Firmware EN 93139 785 320604.Service Flo

37、w Chart 4.3 Recording Process DVDR3360H Eur verification process_final.xls Test disc: Blank DVD+RW Manual Recording with TSBBlank DVD-RWManual Recording Copy to DVD Recordable discTimer Recording Does Timer recording functions ? Yes No Does manual recording No functions ? Yes B Recording Check Make

38、a Timer recording to the HDD or Recordable DVD with: - VPS/PDC on and off - Show View System - manual recording Playback the recorded title Are Timer edit & delete feature working ? Yes No Make a manual recording to the HDD or Recorderable DVD using different recording source: - Cam 1 (Front CVBS) -

39、 Cam 2 (Front S-Video) - DV-in - Tuner - Rear Ext 1/2 (external Cable Box/Satellite Receiver/VCR/DVD) Playback the recorded title Does the TSB feature works ? 1) Switch the Recorder to Tuner source - The active Tuner channel will be recorded into the TSB (time shift buffer), a temporary HDD storage

40、area. 2) By pressing the INFO button the Time shift bar appears on the screen, check the following features: - search forward / backward - instant replay, pause, etc. on the live TV function 1) Make a short recording by selecting a portion in the TSB to be recorded. 2) Playback the recorded title fr

41、om the HDD Content Menu Does the recording functions ? Continue Continue Yes No Yes No Send refurbished set from pool stock to Trade / customer - Attached Defect Description Report and Proof of Purchase. - Pack defective set - Store defective set for pick-up 1) Insert a Recordable DVD 2) In the HDD

42、Content Menu select the recorded title and copy to recordable DVD 3) Playback the copied title Does copy function ? Yes No Recording EN 103139 785 320604.Service Flow Chart 4.4 Playback Process Test disc: DVD Player Test Pack (12NC: 9965 000 25728) CD-RW Printed Audio disc (12NC: 7104 099 96611) Any

43、 Pre-recorded DVD+RW Edit Recordings on the HDD / Recordable DVDPlay a Test disc Yes No C Playback Check 1) Playing the DVD video disc and check the following: - T/C option - INFO option - pause & search functions - change another title, chapter or track - zoom feature Note: Features are dependent o

44、n the kind of Disc Yes NoDoes the set work ? Does the edit features works ? From the HDD Content Menu check the following Title edit features: - Edit, Divide, Delete, Rename, Lock and Protect Does the set work ? Continue Continue Yes No Send refurbished set from pool stock to Trade / customer - Atta

45、ched a Defect Description Report and Proof of Purchase. - Pack defective set. - Store defective set for pick-up. Playing other type of disc: 1) Use discs of DVD PLAYER TEST PACK for: - (Super) Video CD - MP3 disc - Picture disc (slide show) - special DVD playback check by layer change test using DVD

46、 disc of this package 2) DivX 3) For AUDIO CD use of CD-RW printed Audio Disc to check: - Track 3 finger print - Track 8: 600u black dot (max. after 1 min.) Does the edit features works ? From the DVD Disc Menu check the following features: 1) Disc Editing menu: - Rename, Erase, Overwrite, Finalize

47、or Lock disc - Record New Title 2) Title Editing menu: - Edit, Rename, Erase, Append or Overwrite title - Overwrite disc Yes No EN 113139 785 32060 4.5 System Menu Process 4.Service Flow Chart D Setup Menu Check Does the set work ? Continue Yes No Setup Menu - Setup and check the following features:

48、 - Menu Language - Country Selection - TV Shape - Auto Program - Manual Program - Sort Setup Menu - Date / Time and check the following features: - Date - Time Setting - Date - Time Programme - Date (dd / mm / yyyy) - Time (hh : mm) Setup Menu - General and check the following features: - Audio Chapter Marker - Record Quality - DivX(R) Video On Demand - Delete Optical Disc Setup Menu - Preferences and check the following features: - Change Password - Reset Menu Settings - Screensaver Setup Menu - Language and check the