Philips-FWR-7-Service-Manual(1) 电路图 维修手册.pdf

《Philips-FWR-7-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-FWR-7-Service-Manual(1) 电路图 维修手册.pdf（88页珍藏版）》请在收音机爱好者资料库上搜索。

1、Location of printed circuit boards . . . . . . . . . . . . . . . . . . . 1-2 Technical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Measurement setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 RC-5 codes. . . . . . . . . . . . . . . . . . . . . . . . . .

2、 . . . . . . . . . . 2-3 Brief operating instructions. . . . . . . . . . . . . . . . . . . . . . . . 2-4 Warnings for 2-digit numbers, press the keys in rapid succession) to select a track number. 5 Press YES to store your selection in the memory. yThe number of programmed tracks (STEP), Prog and th

3、e total program time are displayed. The track number blinks in the music calendar. 6 Select and store all desired tracks in this way. 7 Press PROG on the unit (PROGRAM on the remote control) to end programming. yPROGstays shown and the program is currently available. Note: If the maximum number of p

4、rogrammable tracks is reached, the display shows Program full. 1 If necessary, press STOP & on the unit ( on the remote control) to stop playback. 2 Press either CD 1, CD 2, CD 3, or CDR to select the desired memory. 3 Press PROG (PROGRAM on the remote control), followed by ! SEARCH or SEARCH ( or o

5、n the remote control) to move through the program steps. yThe track number at the selected step and the total program time are displayed. 4 Press NO to remove the track from the program. yCleared is displayed briefly. yThe next programmed track number will move up to this position and is displayed t

6、ogether with the step number and the remaining total program time. 1 If necessary, press STOP & on the unit ( on the remote control) to stop playback. 2 Press NO. yClear Prog? is displayed. 3 Press YES to clear the program. yProg Cleared will be displayed and PROGgoes off. Note: When you open the CD

7、 recorder tray or the CD changer tray the respective program will be cleared. 1 Select and store all desired tracks in the CD changer memory (see “Programming track numbers”). 2 Enter the recording menu (see “Internal recording”). If the total time of the program is of larger size than the remaining

8、 recording time of the CDR(W): yNot fitting! will be displayed briefly, followed by the remaining recording time and Record Prog? If you nevertheless start recording, only those tracks of the program that fit onto the CDR(W) will be recorded in entirety. To change the program, press NO. yEdit Progra

9、m will be displayed briefly, PROGand the time of the program start blinking. Now you can change the program (see “Programming track numbers”, “Erasing a track from the program” and “Clearing the program”). Making a program for recording Clearing the program Erasing a track from the program Programmi

10、ng track numbers English J O G C O N T R O L TRACKT XT RE CL E V E L SEARCH ED T P R O G E RCH F NAL ZE ERASE REC TYPE CDCD COMP LE CD RECORD M A S E R V O M E P U R E L O U D N E S S N C R E D B L E L Y AU E STOP N O Y S 2-9 Brief Operating Instructions ABOUT RECORDING 18 The CD recorder deck offer

11、s you 3 main functions: Recording from the internal CD changer and tuner or from a selected external source Finalizing your CDR(W) discs and unfinalizing your CDRW discs Erasing a CDRW disc The recording procedure is the same for CDR and CDRW discs. Make sure the CDR(W) is absolutely free of scratch

12、es and dust particles. For recordings, the minimum track length is 4 seconds. You can record up to a maximum of 99 tracks on a disc. The minimum of recording time left on the disc is 7 seconds. Otherwise Does not fit is displayed and you cannot enter the record standby mode. Copyright protection The

13、 Serial Copy Management System (SCMS) prevents the making of a digital copy from a digital copy. The system allows making a digital recording from the original, however in some countries this may require the authorization of copyright holders. When you try to record copy protected material from an e

14、xternal source, Copy Protect will be displayed. No further digital recording is possible then. When you try to record copy protected material from the internal CD changer, no digital recording is possible, however the CD recorder will automatically switch to analog recording. Recording CD text If th

15、e original CD has CD Text, this text will be recorded automatically, provided that the CD text is not copy protected. In that case, recording of CD text will not be possible and Text Protect will be displayed. The CD recorder is equipped with the high-performance Direct Line Recording technique. It

16、ensures a perfect recording of the source material, meaning a true “bit for bit” recording. DLR will always become active when you make normal recordings in listen mode. Auto Level Control ensures that the tracks on the recorded disc have a similar volume level. At all times the already recorded tra

17、cks of the CDR(W) disc will be taken as reference for the volume level of the following recordings. ALC is active when ALC is shown. Auto level control becomes active when: COMPILE CD is being used, a disc, a track or a track edit is being high speed recorded and the CDR(W) has recordings on it, a p

18、rogram (consisting from more than one disc) from the CD changer is being high speed recorded, or CDCD is being used and the CDR(W) has recordings on it. Auto level control will not become active when: CDCD is being used and the CDR(W) has no recordings on it, making recordings from the FM tuner, mak

19、ing recordings from an external source, or making normal recordings in listen mode. You can adjust the reference record level. This is also possible when ALC is active. This feature can be used for fading your recordings in or out. 1 Keep REC LEVEL on the unit pressed to enable the rotary control to

20、 adjust the record level. 2 Turn the rotary control to the left to adjust the desired record level. yThe actual record level (in dB) will be displayed. The record level is reset after the unit has been switched to standby. REC LEVEL key Auto Level Control (ALC) Direct Line Recording (DLR) DO NOT FOR

21、GET TO FINALIZE! Finalizing a CDR(W) disc is a simple procedure, necessary to: play a recorded CDR on a standard CD player or play a recorded CDRW on a CDRW compatible CD player and CD recorder. Basic information English INTERNAL RECORDING 19 For internal recordings you can record from the internal

22、CD changer or tuner. You can choose from the following recording modes: High speed recording and automatic finalizing: Fast and easy! Record and finalize your CDR(W) in one quick step while the sound is muted. You can record the current CD or a program from the CD changer. High speed recording: Reco

23、rd your CDR(W) fast while the sound is muted. You can record an entire CD, a track, a program or a track edit from the CD changer. Normal recording and listening: Listen to the recording while you are making it. You can record an entire CD, a track, a program or a track edit from the CD changer. Man

24、ual recording: Start and stop your recording manually while listening to it. You can do radio recordings from the FM tuner. High speed recording and automatic finalizing of the current disc 1 Make sure the CDR(W) is absolutely free of scratches and dust particles. 2 Press CDCD on the unit to enter t

25、he recording mode. yBoth decks will be selected in the display, the arrow starts blinking. The remaining recording time of the CDR(W), the total playing time of the source CD and Record CD1 (or 2, 3)? are displayed. 3 Press YES to start recording and finalizing. yThe arrow lights, RECORDING IN PROGR

26、ESSis shown, high speed recording and finalizing start, and the actual recording time remaining starts to count down. Note: If a program was already available before pressing CDCD, this will be ignored. PROGgoes off and the current disc will be recorded. After finishing the recording, PROGis shown a

27、nd the program is available again. High speed recording and automatic finalizing (optional) of the current program 1 Make sure the CDR(W) is absolutely free of scratches and dust particles. 2 Press COMPILE CD on the unit to enter the record mode. yBoth decks will be selected in the display, the arro

28、w starts blinking. The remaining recording time of the CDR(W), the total playing time of the source CD and Record Prog? are displayed. 3 Press either: YES to confirm, or NO to change the program. yPROGstarts blinking. Now you can change the program (see “Program”) and return to the record mode by pr

29、essing COMPILE CD. 4 Auto Fin? is displayed. Press either: YES, if the CDR(W) is to be finalized after recording, or NO, if the CDR(W) is not to be finalized after recording. yThe arrow lights, RECORDING IN PROGRESSis shown, high speed recording and finalizing (if selected) start and the actual reco

30、rding time remaining starts to count down. Note: If no program is available and you press COMPILE CD, you enter immediately into the program menu. Start your programming and return to the record mode by pressing PROGRAMor COMPILE CD. DO NOT FORGET TO FINALIZE! Finalizing a CDR(W) disc is a simple pr

31、ocedure, necessary to: play a recorded CDR on a standard CD player or play a recorded CDRW on a CDRW compatible CD player and CD recorder. High speed recording and automatic finalizing Recording modes English J O G C O N T R O L TRACKTEXT RE CL E V E L SEARCH ED T P R O G S ARCH F NAL ZE ERASE REC T

32、YPE CDCD COMP LE CD RECORD E S N O M A S T E R V M P U R E L O U D N E S S I N C R E D B L E PL Y PAU E STOP E S 2-10 Brief Operating Instructions INTERNAL RECORDING 20 High speed recording of an entire disc, a track, a program or a track edit 1 Make sure the CDR(W) is absolutely free of scratches a

33、nd dust particles. 2 Press either CD 1, CD 2 or CD 3 to select the disc from which you wish to record. 3 Press REC TYPE on the unit to enter into the recording menu. 4 Rotate JOG CONTROL to select one of the following high speed recording modes: If a disc from the CD changer is selected: yCD Fast?:

34、for high speed recording of an entire disc Continue with step 5. yTrack Fast?: for high speed recording of a track Press YES to confirm. Rotate JOG CONTROL to select the track. yRec Tr and the track number is displayed. Continue with step 6. If CD changer program mode is available: yProg Fast?: for

35、high speed recording of the selected disc or of the program If CD changer track edit mode is available: yA-B Fast?: for high speed recording of the AB track 5 Press YES to confirm your selection. yBoth decks will be selected in the display, the arrow starts blinking. The remaining recording time of

36、the CDR(W), the total recording time of the CDR(W) and either Record CD1 (or 2, 3)?, Record Prog? or Record A-B? is displayed. Note: When the CDR(W) already contains a recording, ALC will also become active and ALCwill be shown. 6 Press YES to start high speed recording. yThe arrow lights, RECORDING

37、 IN PROGRESSis shown, high speed recording starts and the actual recording time remaining starts to count down. To stop recording, press STOP & on the unit. Normal recording and listening of an entire disc, a track, a program or a track edit 1 Make sure the CDR(W) is absolutely free of scratches and

38、 dust particles. 2 Follow steps 2 and 3 of “High speed recording”. 3 Rotate JOG CONTROL to select one of the following normal record options: If CD changer is selected: yCD Listen?: for listening to the entire disc during normal recording yTrackListen?: for listening to the track during normal recor

39、ding Press YES to confirm. Rotate JOG CONTROL to select the desired track. yRec Tr and the track number is displayed. Continue with step 6 of “High speed recording”. If CD changer program mode is available: yProg Listen?: for listening to the program during normal recording If CD changer track edit

40、mode is available: yA-B Listen?: for listening to the AB track during normal recording 4 Follow steps 5 and 6 of “High speed recording”. To stop recording, press STOP & on the unit. DO NOT FORGET TO FINALIZE! Finalizing a CDR(W) disc is a simple procedure, necessary to: play a recorded CDR on a stan

41、dard CD player or play a recorded CDRW on a CDRW compatible CD player and CD recorder. Normal recording and listening High speed recording English CD RECORDABLE M N H F SYSTEM STANDBY ON CD 1 CD 2 CD 3 D SP AY CDR R SENSOR TUNER D G A A A OG AUX D XC OCM OP N CLOSE O G O N T R O L ACKX E C E V E L S

42、EA CH ED T P R A A F N L ZE ERASE EC TYPE CDCD COMP L CD RECORD E N M A S T E R V O L U M E D S C P U R E L O U D N E S S N C E D B E U R R N D FWR7 CD TEXT ED T NG CD RECORDER E S OP INTERNAL RECORDING 21 Manual recording from the FM tuner 1 Make sure the CDR(W) is absolutely free of scratches and

43、dust particles. 2 Press TUNER repeatedly to select the FM tuner. Then select the desired radio station (see “Tuning to radio stations”). 3 Press REC TYPE on the unit to enter the recording menu. yFM Tuner? is displayed. 4 Press YES to confirm. yWait and Record? are displayed. 5 Press YES to start re

44、cording. yThe arrow lights, RECORDING IN PROGRESSis shown, manual recording starts and the actual recording time remaining starts to count down. 6 Press STOP & to stop recording. DO NOT FORGET TO FINALIZE! Finalizing a CDR(W) disc is a simple procedure, necessary to: play a recorded CDR on a standar

45、d CD player or play a recorded CDRW on a CDRW compatible CD player and CD recorder. Manual recording English CD RE ORDAB E M N H F S STEM STANDBY ON CD 1 CD 2 CD 3 D SPLAY CDR R EN OR TU ER D G A NAG AUX CD XCCK O EN C OSE O G C O N T R O L RACKEX RE CL E E L S A CH ED T P R A A F N L ZE E ASE REC T

46、 PE DCD COMPE CD ECORD S N M A S T R V O L U M E S C P U R E O U D E S S N C R E D L E U R N D FWR7 CD TEXT ED T NG CD RECORDER S SP 2-11 Brief Operating Instructions EXTERNAL RECORDING 22 When making recordings from an external source, we recommend to do analog recording only if digital recording i

47、s not possible. Digital recording will usually result in better sound quality. Recording of an entire disc or a track with automatic start 1 Make sure the CDR(W) is absolutely free of scratches and dust particles. 2 Repeatedly press DIGITAL / ANALOG AUX to select the input for the external source fr

48、om which you want to record. yAUX Digital is displayed if the digital input is selected. yAUX Analog is displayed if the analog input is selected. 3 Press REC TYPE on the unit to enter the recording menu. 4 Rotate JOG CONTROL to select either: yAUX CD?: for recording with synchronized start of an en

49、tire disc yAUX Track?: for recording with synchronized start of a track 5 Press YES to confirm your selection. yStart Source, AUX and the remaining recording time of the CDR(W) are displayed. 6 Start playback on the selected source. yThe CD recorder starts to record simultaneously and RECORDING IN PROGRESSis shown. The remaining recording time on the CDR(W) is displayed. Note: If you start playback on the selected source within a track, recording starts at the beginning of the next track or after 2.7 seconds of silence in analog recordings. 7If a