Philips-DVD-723-743-Service-Manual(1) 电路图 维修手册.pdf

《Philips-DVD-723-743-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-DVD-723-743-Service-Manual(1) 电路图 维修手册.pdf（78页珍藏版）》请在收音机爱好者资料库上搜索。

1、Published by MW 0263 Service PaCEPrinted in the NetherlandsSubject to modificationEN 3122 785 12240 Copyright 2002 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any for

2、m or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. DVD-Video PlayerDVD723-743 DVD723 /001 /021 /051 DVD743 /001 /021 /051 ContentsPage 1Technical Specs and Connection Facilities2 2Safety Instructions, Warnings, Notes, and Service Hints4 3Di

3、rections for Use6 4Mechanical- and Dismantling Instructions19 5Diagnostic Software, Trouble Shooting and Test Instructions22 6Wiring-, Block Diagrams Block Diagram41 Wiring Diagram42/43 7Electrical Diagrams and Print-LayoutsDiagram PWB Power Supply Unit4445 AV Board: Video if it is, press OPEN/CLOSE

4、, if it is not, press STOP. By pressing PLAY the script will proceed to the next test. If the user presses PLAY before OPEN/CLOSE or STOP, the DispLed nucleus will return TRUE (LED test successful). 5.3.3Keyboard Test The keyboard of the DVD player is tested by nucleus DispKeyb. The user is expected

5、 to press all keys on the local keyboard once. The code of the key pressed is shown on the local display (1 hexadecimal digit) immediately followed by a (hexadecimal) number indicating how many times that key has been pressed. Example of the local display during this test: Figure 5-7 The key-codes d

6、isplayed on the local display will scroll from right to left when the display gets full, the text K will remain on display. Figure 5-8 If any keys are detected more than once (due to hardware error), the key-code is displayed twice (or more), with the second digit increased by 1. If the user does no

7、t press all keys minimally once (in any order), the DispKeys nucleus will return FALSE and cause an error in the overall result of the player script. The user can leave the keyboard test by pressing the PLAY key on the local display of the DVD player for at least one full second. The result of the k

8、eyboard test is shown on local display as follows: Figure 5-9 Or Figure 5-10 Pressing PLAY on the local keyboard again will proceed to the next text. 5.3.4Remote Control Test The remote control of the DVD player is tested by nucleus DispRc. The user must press any key on the remote control just once

9、. The codes of the key pressed will be shown on the local display in hexadecimal format. Example: Figure 5-11 If OK, press OPEN/CLOSE If OK, press OPEN/CLOSE If OK, press OPEN/CLOSE If NOK, press STOP If NOK, press STOP If NOK, press STOP press PLAY to continue CL 16532162_031.eps 080102 CL 19653216

10、2 032 eps 080102 KEY IDKEY 0PLAY/PAUSE 1STOP 2OPEN/CLOSE 3STANDBY 4NEXT 5PREVIOUS 7SMART PICTURE 8NAVIGATION -UP 9NAVIGATION -DOWN ANAVIGATION - LEFT BNAVIGATION - RIGHT CDISC MENU DOK ESOUND CL 26532039_027.eps 203020 CL 16532162 033 eps 080102 CL 16532162 034 eps 080102 CL 16532162 035 eps 140102

11、Diagnostic Software, Trouble Shooting and Test InstructionsEN 25DVD 723-7435. In this example 23 is the hexidecimal code of the pressed RC key. The user can leave the remote-control test by pressing PLAY on the local keyboard of the DVD player. The remote control test is successful if a code was rec

12、eived before the user pressed the PLAY key. Pressing the PLAY key, before pressing a key on the remote control, gives an error in the remote control test (note that the remote control test will also fail if a key on the remote control was pressed but no code was received). The remote control test do

13、es not check upon the contents of the received code, that is it will not be checked if the received code matches the key pressed. If desired, the user can manually check this code by using a code-table for the remote control key-codes. Figure 5-12 After pressing PLAY, the result of the remote contro

14、l test is displayed on the local display of the DVD player as follows: Figure 5-13 Or Figure 5-14 Pressing PLAY on the local keyboard again will proceed to the next test. 5.3.5P50 Loop-Back Test For the P50 loop-back test, the user must first press a key to decide if the test is to be performed. The

15、 display will show the following message: Figure 5-15 If the user presses STOP, the P50 test will be skipped. If the user presses OPEN/CLOSE, the P50 test is performed and the result is displayed as follows: Test successful: Figure 5-16 Test fails: Figure 5-17 Press the PLAY key to continue to the n

16、ext text RC Key id Hexadecimal code STANDBY0C 11 22 33 44 55 66 77 88 99 00 RETURN83 DISPLAYEF DISC MENU54 SYSTEM MENU82 CURSOR UP58 CURSOR DOWN59 CURSOR LEFT5A CURSOR RIGHT5B OK5C PREVIOUS21 NEXT20 STOP31 PLAY2C PAUSE30 SUBTITLE4B ANGLE85 ZOOMF7 AUDIO4E REPEAT1D REPEAT A-B3B SHUFFLE1C SCAN2A CL 165

17、32162_037.eps 080102 CL 96532065 013 eps 120799 CL 96532065 014 eps 120799 CL 16532007 004 eps 090102 CL 16532007 005 eps 090102 CL 16532007 006 eps 090102 Diagnostic Software, Trouble Shooting and Test InstructionsEN 26DVD 723-7435. 5.4Mono PCB Digital Part 5.4.1Picture Test The picture test is per

18、formed by putting a predefined picture (colour bar) on the display (nucleus VideoColDencOn), and asking the user for confirmation. The display will show the following message: Figure 5-18 By pressing OPEN/CLOSE the user confirms the test, pressing STOP will indicate the picture was invisible or inco

19、rrect. Pressing PLAY will proceed to the next test. If the user presses PLAY without pressing OPEN/CLOSE or STOP first, the result of this test will be TRUE (picture ok). Note: The colour bar must be simultaneously available on the CVBS, YC, and RGB (or YUV) outputs available. On the SCART only the

20、CVBS and RGB signals will be available. 5.4.2Sound 1 note that this test will not contribute to the test result of the Basic Engine. Pressing PLAY proceeds to the next test, after the disc motor has been shut off with a call to nucleus BeDiscMotorOff. 5.5.8Tray Test As a last action for the Basic En

21、gine tests, the tray test is repeated. The local display will look as follows: Figure 5-29 This test is meant to give the user the opportunity to remove the disc in the tray. The tray position can be toggled using the OPEN/CLOSE key. The tray will be closed (by the software, if it is open) before pr

22、oceeding to the next test when the user presses the PLAY key. 5.5.9Error Log (See Table on Page 25) Reading the error log and error bits information can be useful to determine any errors that occurred recently during normal operation of the DVD player. Reading the error log is done by nucleus LogRea

23、dErr. The display during the errorlog readout looks as follows : Figure 5-30 Note: Previous versions of the diagnostic software showed a 8-digit error code. Due to limitations in the number of digits that can be displayed by some front panel displays, the most significant digits will not be shown. T

24、his can be done since all the error codes used by this player has set these 2 digits to “00” By pressing OPEN/CLOSE or STOP the user can move forward or backward (respectively) through the logged error codes. If 0000 is displayed at all positions, the error log is empty. Display of the logged errors

25、 is done in a cyclic manner. By pressing PLAY on the local keyboard, the user can proceed to the next test. 5.5.10 Error Bits Reading the error bits is done by nucleus LogReadBits. The display during the errorbits readout looks as follows: Figure 5-31 Only the identification number (decimal) represe

26、nting set errorbits will be shown. By pressing OPEN/CLOSE or STOP, the user can move forward or backward (respectively) through the logged errorcodes. If the display only shows EB-0, no error bits were set. By pressing PLAY the user can continue to the next test. 5.6Loop Test (See Table Below) At th

27、e start of the loop test, the local display of the DVD player will show the interactive player test result readout in the following display: Figure 5-32 The left side of the display contains a 3-digit code, which can have a value between 000 and 111. These values indicate the faulty modules and are

28、to be interpreted as follows: Figure 5-33 The loop test will perform the same nuclei as the dealer test, but it will loop through the list of nuclei indefinitely. The display of the DVD player will display not only the three digits indicating correct/faulty modules and the last found error code (as

29、mentioned, faults are detected as far as they can be within the scope of the diagnostic software), but also a loop counter indicating how many times the loop has been gone through. If an error was detected, the display will remain as in figure 5-34 until the user presses the PLAY key and then it wil

30、l continue to the next loop. Example: Figure 5-34 The 2-digit number (23) on the right of figure 5-32 indicates the number of times the loop test has been performed. CL 16532162 046 eps 080102 CL 16532162 041 eps 080102 CL 16532162 047 eps 080102 CL 16532162 048 eps 080102 CL 16532162 049 eps 080102

31、 Displayed Value Indication for each module Basic EngineMono PCB Display PCB 000okokok 001okokfaulty 010okfaultyok 011okfaultyfaulty 100faultyokok 101faultyokfaulty 110faultyfaultyok 111faultyfaultyfaulty CL 96532065 031 eps 120799 CL 16532162 050 eps 080102 Diagnostic Software, Trouble Shooting and

32、 Test InstructionsEN 29DVD 723-7435. After one loop cycle: Display the 3-digit module bits together with the last error code which occured in the loop test. The 4 digits at the right side of the display (fig. 5-34) show the last error that was found during the loop test. The leftmost two digits (54)

33、 of this code indicates which nucleus resulted in a fault. The rightmost two digits (03) refer to the faultcode within that nucleus. For further explanation of this error code, refer to chapter 5.8 (Nuclei Error Codes). 5.6.1Errorlog Explanation: The application errors will be logged in the NVRAM. T

34、he maximum number of error bytes that will be visible is 16. The first word (4 digits) of the byte is the component identification, the last word is the error code. The diagnostics software will present a combination of this component identification plus an error code on the local display (and on th

35、e attached terminal). The last reported error is shown as and the errors in between as . The devices that may report errors are the serial controller (UART), the basic engine (BE), the slave processor (SLPH), the SACD Stream Manager (SSM) and the SACD Media Access (SMA). The identification of these

36、components is as follows: The tables in the next chapters list the error code and corresponding problem. The column Explanation holds a more elaborate description and the most likely reason for the error. Some Examples: 002E0000 (SMA reported a timeout error) 0016010A (Engine could not fully close o

37、r open the tray) D0010001 (Flash checksum failed). For further explanation of DS errors, see description of nucleui error codes in paragraph 5.8. UART Error Codes BE Errors SLPH Error Codes SSM Error Codes Component nameComponent identification Serial controller (UART)000A Engine (BE)0016 Slave Proc

38、essor (SLPH)001A SACD Stream Manager (SSM) 001C SACD Media Access (SMA)002E Diagnostic software (DS)Dxxx Error Number Error nameExplanation 0000BUF_OVE RFLOW To many characters were offered in too little time. Reason: system was too busy doing other jobs. 0001COMMUNI CATION Usually a protocol error.

39、 Reason: bad connection between engine and processor. 0002TIME OUT Error Number Error nameExplanation 0101S2B_ILL_CO MMAND Parameter(s) not valid for this command. Reason: some communication problem between UART and engine. 0102S2B_ILL_PAR AM Command not allowed in this state or unknown. Reason: see

40、 S2B_ILL_COMMAND error 0103S2B_SLEDGE Sledge could not be moved to home position. 0104S2B_FOCUSFocus failure 0105S2B_MOTORMotor could not reach speed within timeout 0106S2B_RADIALServo didnt get on track after several retries. 0107S2B_PLL_LO CK PLL could not lock in Accessing or Tracking state 0108S

41、BC_HEADE R_TO Header timeout 0109S2B_SBC_NO T_FOUND Requested subcode item could not be found. 010AS2B_TRAYTray could not be opened or closed completely. 010BS2B_TOC_RE AD TOC could not be read within timeout period. 010CS2B_JUMPRequested seek could not be performed. 010DS2B_NON_EX IST_SES Attempt t

42、o access a non-existing session. 010ES2B_NON_EX IST_BCA Caller tries to acces a non- existing BCA area 010FSpeed settingA wrong or inappropraiate speed value has been set 0116NO_DISCNo disc selected 011ATRAY_INITAfter reset, initialized tray 011BNO TOC INFO No TOC information in lead-in area or eras

43、e TOC found 01F0S2B_OVERR UN Too many bytes received over S2B Reason: see S2B_ILL_COMMAND error 01F1S2B_COMM_ TO Not enough bytes are received over S2B Reason: see S2B_ILL_COMMAND error 01F2S2B_PARITYByte received with parity error. Reason: see S2B_ILL_COMMAND error 01F3S2B_ILL_PHA SE CMD IDC is not

44、 valid, transmission out of sync. Reason: see S2B_ILL_COMMAND error 01F4S2B_ILL_NR_ OF_BYTES Byte count has an illegal value. Reason: see S2B_ILL_COMMAND error Error Number Error nameExplanation 0000COMMUNICA TION Error in I2C communication. Reason: bad connection between slave processor and main pr

45、ocessor. Error CodeError nameExplanation 0006SP_SYNCER ROR System cannot get synchronised with sectors coming from disc. Reason: Usually a damaged disc or the player was dropped/ pushed during operation. If not, the engine is malfunctioning. 0007SP_EDCERR OR Data coming from disc is damaged. Reason:

46、 see SP_SYNCERROR Error Number Error nameExplanation Diagnostic Software, Trouble Shooting and Test InstructionsEN 30DVD 723-7435. SMA Error Codes 5.6.2Reprogramming of New Mono Boards. Figure 5-35 0008SP_CONTINU ITYERROR Sequence of sectors coming from disc is incorrect. Reason: see SP_SYNCERROR 00

47、09DMX_CONTI NUITYERRO R Sequence of sectors is incorrect. Reason: problem with buffer RAM 000ALLD_ERRORAn illegal audio format was offered to the decoder. Reason: unknown audio type on disc or problem with buffer RAM 000BBCU_ERRORInternal problem in Furore chip Error CodeError nameExplanation Error

48、NumberError nameExplanation 0000SMA_TIMEO UTERROR Data coming from disc not in time. Reason: damaged disc or engine problem. Caution This information is confidential and may not be distributed. Only a qualified service person should reprogram the mono board. After reset of NV-memory or repair of the

49、 mono board, all the customer settings and also the region code will be lost. Reprogramming of the mono board will put the player back in the state in which it has left the factory, i.e. with the default settings and the allowed region code. Reprogramming will be done by way of the remote control. Put the player in stop mode, no disc loaded. Reprogramming is limited to 25 times When the counter reaches 25, reprogramming is not possible anymore Press the following keys on the remote control: followed by numerical keys The display shows: “- - - - - - - - - - -” Pre