Philips-DVD-733-K-Service-Manual(1) 电路图 维修手册.pdf

《Philips-DVD-733-K-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-DVD-733-K-Service-Manual(1) 电路图 维修手册.pdf（43页珍藏版）》请在收音机爱好者资料库上搜索。

1、Published by MW 0165 Service PaCEPrinted in the NetherlandsSubject to modification?3122 785 11230 Copyright 2001 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form

2、or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. DVD-Video PlayerDVD733K DVD733K /691 /781 CL 16532007_109.eps 020501 ContentsPage 1Technical Specifications And Connection Facilities2 2Warnings, Laser Safety Instructions And Notes 3 3Direct

3、ions For Use6 4Mechanical Instructions And Exploded Views14 5Diagnostic Software Descriptions And Troubleshooting19 6Block and Wiring Diagram Block Diagram37 Wiring Diagram38 7Electrical Diagrams And Print-LayoutsDiagram PWB Power Supply3940-41 A/V Board Video(Diagram A1)4244-47 A/V Board Audio(Diag

4、ram A2)4344-47 Display Panel(Diagram D)4849-51 Microphone And HP Panel(Diagram K)5253-54 Bare Board Standby5555 8Electrical Alignments57 9Circuit Descriptions And57 List Of Abbreviations60 10 Spare Part List61 RadioFans.CN 收音机爱 好者资料库 Technical SpecificationsGB 2DVD733K /691/7811. 1.Technical Specifi

5、cations English Specifications PLAYBACK SYSTEM DVD Video Video CD PAUSE interrupts playback 9 STOP stops playback Caution: Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit. COAXIAL DIGITAL AUDIO OUT PCM-MPEG2-Dolby Digital-DTS

6、 LR(CVBS) VIDEO OUTAUDIO OUTS-VIDEO OUT (Y/C) SUBW.OPT OUT 1 2 1 2 YPB/CBPR/CR VIDEO OUT MAINS (AC Power) connect to power source COAXIAL (Digital audio out) connect to digital (coaxial) audio equipment OPT OUT (Digital audio out) connect to digital (optical) audio equipment SUBW. (Subwoofer) connec

7、t to an active subwoofer S-VIDEO OUT (Y/C) connect to a TV with S-Video (Y/C) inputs PR/CR PB/CB Y VIDEO OUT connect to a TV with PR/CR PB/CB Y inputs (CVBS) VIDEO OUT connect to a TV with CVBS video inputs AUDIO OUT (Left/Right) connect to an amplifier, receiver or stereo system PHONES LEVEL connec

8、t to headphone / volume control for headphone LEVEL 1 ) pause playback temporarily / frame-by-frame playback REPEAT repeat chapter, track, title, disc REPEAT (A-B) repeat a specific segment SHUFFLE play tracks in random order SCAN play the first 10 seconds of each track/chapter within a disc POWER B

9、 switches DVD ON or to standby-on mode 0-9 numerical key pad select numbered items in a menu DISPLAY display bit rate indicator during playback SYSTEM MENU access or remove the players menu T search forward* / go to the next chapter or track SUBTITLE select a subtitle language ANGLE select a DVD cam

10、era angle ZOOM enlarge video image AUDIO select an audio language KARAOKE ( i ) to switch ON/OFF karaoke mode KEY changing key of vocal range VOCAL select various vocal support mode MODE select between VCD/DVD karaoke disc * Press and hold key for about two seconds Remote Control Directions For UseG

11、B 8DVD733K /691/7813. 10 English Menu Bar/Status Window As there are multiple menu bars, the items on the menu bar are arranged according to usage and availability of direct access keys. Pressing the SYSTEM MENU keys repeatedly will toggle through menu bar 1, menu bar 2, menu bar 3 and OFF. Menu bar

12、 1 Personal Preferences Subtitle Language Audio Language Color Sound Menu bar 2 Step by step playback Slow motion Fast motion Angle Zoom Menu bar 3 Title Chapter Time Search Favorite Track Selection (FTS) Temporary Feedback Field Icons Scan Repeat All Repeat Title Repeat Track Repeat Chapter Shuffle

13、 Shuffle Repeat Repeat A to end Repeat A-B Angle Child Lock On Child Safe Resume Action prohibited Personal Preferences You can set your own personal preferences on the player. General operation: Press SYSTEM MENU on the remote control. Select in the menu bar. The Personal Preferences menu appears.

14、Use the 1 2 3 4 keys to toggle through the menus, submenus and submenu options. When a menu item is selected, the cursor keys (on the remote control) to operate the item are displayed next to the item. Press OK to confirm and return to the main menu. The following items can be adapted: Picture TV Sh

15、ape If you have a wide screen (16:9) TV, select 16:9. If you have a regular (4:3) TV, select 4:3. If you have a 4:3 TV, you can also select between: Letterbox for a wide-screen picture with black bars at the top and bottom of the screen, or Pan Scan, for a full-height picture with the sides trimmed.

16、 If a disc supports the format, the picture will be shown accordingly. Black level shift (NTSC users only) Select ON for adapting the color dynamics to obtain richer contrasts. Video shift The factory centers the video on your TV screen. Use this setting to personalize the position of the picture on

17、 your TV by moving it to the left or right. PREPARATION9 English Connecting to an active subwoofer 1Connect the active subwoofer to the SUBWOOFER OUT audio out jack (C). The subwoofer reproduces just the low bass sound effect (e.g. explosions, the rumble of spaceships, etc.). Be sure to follow the i

18、nstructions supplied with the subwoofer. TV XY Z COAXIAL DIGITAL AUDIO OUT PCM-MPEG2-Dolby Digital-DTS LR(CVBS) VIDEO OUTAUDIO OUTS-VIDEO OUT (Y/C) SUBW.OPT OUT 1 2 1 2 YPB/CBPR/CR VIDEO OUT AMPLIFIER A FGC ACTIVE SUBWOOFER Note: If the audio format of the digital output does not match the capabilit

19、ies of your receiver, the receiver will produce a strong, distorted sound or no sound at all. Six Channel Digital Surround Sound via digital connection can only be obtained if your receiver has a Digital Multi- channel decoder. To see the selected audio format of the current DVD in the Status Window

20、, press SYSTEM MENU. NTSC/PAL Settings You can switch the NTSC/PAL setting of the DVD player to match the video signal of your TV. This setting only affects the televisions on-screen display that shows the stop and setup modes. You may select either NTSC or PAL. To change the DVD player setting to P

21、AL or NTSC, follow the steps below. 1Press the POWER ON/OFF button on the front panel of the DVD player to turn OFF the DVD player. 2Press and hold 9 and T on the front of the DVD player. While holding 9 and T, press POWER ON/OFF. 3After PAL or NTSC appears on the display of the DVD player, release

22、9 and T at the same time. The PAL or NTSC indicator that appears on the display indicates the current setting. 4To change the setting, press T within three seconds. The new setting (PAL or NTSC) will appear on the display. NTSC/PAL Conversion This player is equipped with a NTSC/PAL conversion featur

23、e to convert the video output of the disc to match your TV system. The conversions supported are as below: NTSCPALNTSC Not Supported PALPAL NTSCPALNTSC NTSCPALPAL DiscOutput format Type DVD VCD NTSC FormatSelected mode PAL NTSC PAL NTSCPALAUTO 1In the Preference Menu, select TV System. 2Press 3 or 4

24、 to select PAL, NTSC or AUTO. Notes: AUTO can only be selected when using a TV that has both the NTSC and PAL systems. This is applicable for CVBS output on cinch and SCART only Slight picture distortions may occur due to this conversion. This is normal. Thus, the AUTO format is most suitable for th

25、e best picture quality. General Explanation About this manual This manual gives the basic instructions for operating the DVD player. Some DVDs require specific operation or allow only limited operation during playback. When this occurs, the symbol appears on the TV screen, indicating that the operat

26、ion is not permitted by the player or the disc. Remote control operation Unless stated, all operations can be performed by the remote control. Always point the remote control directly at the player, making sure there are no obstructions between the remote and the player. Corresponding keys on the fr

27、ont panel of the player can also be used. Menu bar operation A number of operations can be done with the menu bar on the screen. The menu bar can be accessed by pressing the cursor keys on the remote control. Pressing SYSTEM MENU while the menu bar is displayed will clear the menu bar from the scree

28、n. The selected item will be highlighted, and the appropriate cursor keys to operate it will be displayed below the icon. The symbols indicate more items are available at the left/right of the menu bar. Press 1 or 2 to select these items. PREPARATION Directions For UseGB 9DVD733K /691/7813. 12 Engli

29、sh Loading Discs 1Press OPEN/CLOSE on the front of the player to open the disc tray. 2Load your chosen disc in the tray, label side up. 3Press OPEN/CLOSE again to close the tray. READ appears in the status window and on the player display, and playback starts automatically. Note: If Child Lock is se

30、t to ON and the disc inserted is not authorized, the 4-digit code must be entered and/or the disc must be authorized (see Access Control). Playing a DVD Video and Video CD Playing a disc After inserting the disc and closing the tray, playback starts automatically. The status window of the player dis

31、play shows the type of disc loaded, as well as the discs information and playing time. The disc may invite you to select an item from a menu. If the selections are numbered, press the appropriate numerical key; if not, use the 4 3 1 2 keys to highlight your selection, then press OK. The number of th

32、e current title and chapter are displayed. Playback may stop at the end of the Title and you may return to the DVD disc menu. To go to the next title, press B. To stop playback, press 9. The default screen will appear, giving information about the current status. You can resume playback from the poi

33、nt at which you stopped playback. Press B; when you see the Resume icon . on the screen, press B again. The RESUME feature applies not only to the disc in the player, but also to the last four discs you have played. Simply reload the disc and press RESUME on the remote control. Or, press B when you

34、see the Resume icon . on the screen, then press B again. Note: DVDs may have a region code. Your player will not play discs that have a region code different from the region code of your player. General Features Note: Unless stated, all operations described are based on remote control use. Some oper

35、ations can be carried out using the menu bar on the screen. Moving to another title/ chapter When a disc has more than one title or chapter, you can move to another title/chapter as follows: Press SYSTEM MENU, then select or in the menu bar. Press 3 or 4 to select a title/chapter. Slow Motion Select

36、 (SLOW MOTION) in the menu bar. Use the 4 keys to enter the SLOW MOTION menu. Playback will pause. Use the cursor keys 1 2 to select the required speed: -1, -1/2, -1/4 or -1/8 (backward), or +1/8, +1/4, +1/2 or +1 (forward). Select 1 to play the disc at normal speed again. If ; is pressed, the speed

37、 will be set to zero (PAUSE). To exit slow motion mode, press B or 3. Still Picture and Frame-by-frame playback Select (STEP) in the menu bar. Use the 4 key to enter the step by step menu. Playback will pause. Use the cursor keys 1 2 to select the previous or next picture frame. To exit step by step

38、 playback, press B or 3. You can also step forward by pressing ; repeatedly on the remote control. Scan Scanning plays the first 10 seconds of each chapter/track on the disc. Press SCAN. To continue playback at your chosen chapter/track, press SCAN again or press B. OPERATION Operation 11 English Co

39、lor settings You can select one of five predefined sets of color settings and one set (Personal) which you can define yourself. Personal color Allows you to fine-tune the selected color settings saturation, brightness and contrast. Sound Digital output Factory setting: ALL. This means coaxial output

40、 is on. If you are not connecting to equipment with a digital input, change the setting to OFF. If your equipment doesnt include a digital multi-channel decoder, set the digital output to PCM only (Pulse Code Modulation). Analog output Select Stereo, Dolby Surround or 3D Sound (TruSurround) to match

41、 your systems playback capability. Subwoofer cut-off The frequency of the subwoofer output can be set to HIGH (200Hz) or LOW (100Hz) to match your systems playback sound quality. Night Mode Optimizes the dynamics of the sound for low volume playback. Language Select the required Menu, Audio and Subt

42、itle language. Audio language and Subtitle language can also be adapted using the Menu bar. Features Access Control Access Control contains the following features: Child Lock - When Child Lock is set to ON, a 4-digit code must be entered in order to play discs. Parental control - Allows the conditio

43、nal viewing of DVDs containing Parental Control information (see Access Control). Status Window Displays the current status of the player and appears with the menu bar. When disc playback is stopped, it is displayed with the Temporary Feedback Field in the default screen. See On-Screen Display infor

44、mation. The factory setting is ON. Select OFF to suppress display of the Status Window. Bit Rate Indicator When activated, the bit rate for video and audio, as well as the total bit rate is displayed. This is only applicable during playback of DVD and SVCD discs. Help text When set to ON, help text

45、describes the icons selected. Select OFF if you no longer require the help text. PREPARATION Directions For UseGB 10DVD733K /691/7813. 14 English FTS-Video The FTS-Video function allows you to store your favorite titles and chapters (DVD) and favorite tracks and indexes (VCD) for a particular disc i

46、n the player memory. FTS program can contain 20 items (titles, chapters etc.). A programmed FTS will be placed on top of the list when playback is activated. When the list is full, a new program will replace the last program on the list. The program can be selected and played at any time. Storing an

47、 FTS-Video Program While playback is stopped, select VIDEO FTS c in the menu bar. Press 4 to open the menu. The VIDEO FTS menu appears. Press 2 or 1 to select ON or OFF. Storing titles/tracks Press 4 to select TITLES. Use 2 and 1 to select the required title. Press OK if you wish to store the entire

48、 title. The title number will be added to the list of selections. Storing chapters/indexes Press 4 on the selected title number. The title number will be marked and the highlight moves to the first available chapter number for this title. Use 2 and 1 to select the required chapter number. Press OK t

49、o confirm the selection. The title/chapter selection will be added to the list of selections. Press SYSTEM MENU to exit the VIDEO FTS c menu. Erasing an FTS-Video Program While playback is stopped, select VIDEO FTS c in the menu bar. Use 4 to select PROGRAM. Use 2 and 1 to select the required number. Press OK to erase the selection. Press SYSTEM MENU to exit. Erasing all selections While playback is stopped, select VIDEO FTS c in the menu bar. Use 4 to select CLEAR ALL. Press OK. All selections will be erased. Press SYSTE