Philips-EXP-411-Service-Manual(1) 电路图 维修手册.pdf

《Philips-EXP-411-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-EXP-411-Service-Manual(1) 电路图 维修手册.pdf（40页珍藏版）》请在收音机爱好者资料库上搜索。

1、Technical Specification.1-1 Instructions For Use .1-2.1-6 Service Aids.1-7 Handling Chip Components.1-7 Safety .switches the set on, starts playback and interrupts playback + +/ .MP3-CD only: selects the next/previous album or skips forward/backward # / .skips forward/backward and searches forward/b

2、ackward $ OPEN2 .opens the CD lid CONTROLS (see figure 1) % .type plate 4.5V DC .to connect the external power supply GENERAL INFORMATION Maintenance Do not touch the lens A of the set. Do not expose the set, battery or discs to humidity, rain, sand or excessive heat (caused by heating equipment or

3、direct sunlight). The lens may cloud over when the set is suddenly moved from cold to warm surroundings. Playing is not possible then. Leave the set in a warm environ- ment until the moisture evaporates. Active mobile phones in the vicinity of this set may cause malfunctions. Avoid dropping the set

4、as this may cause damage. Clean the set with a soft, lint-free cloth. Do not use any cleaning agents as they may have a corrosive effect. To clean a disc, wipe it in a straight line from the centre towards the edge using a soft, lint-free cloth. Cleaning agents may damage the disc. Environmental inf

5、ormation All redundant packing material has been omitted. We have done our utmost to make the packaging easily separable into three mono materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet). Your set consists of materials which can be recycled if disas

6、sembled by a specialized company. Please observe the local regulations regarding the disposal of packing materials, exhausted batter y and old equipment. INSTRUCTIONS FOR USE RadioFans.CN 收音机爱 好者资料库 1-3 GENERAL INFORMATION MP3 music files The music compression technology MP3 (MPEG Audio Layer 3) red

7、uce the digital data of an audio CD significantly while maintaining CD-like sound quality. With MP3, for example, you can record up to 3 hours of CD-like music on a single CD-ROM. This set plays MP3 music files. How to get music files Either download legal music files from the Internet to your compu

8、ter disk or buy pre-recorded music CD. For this, insert an audio CD into your computers CD-ROM drive and convert the music using an appropriate encoder software. To achieve a good sound quality, a bit rate of 128 kbps or higher is recommended for MP3 music files. Some encoder software offers an opti

9、on to protect music files, i. e. the files can only be played on the computer which created them. If you burn such files on a CD-ROM, you cannot play them on this set. Make sure to deactivate the protection option in the encoder software before creating the music files. In this case you are responsi

10、ble for adherence to all local or international copyrights. How to organize music files In order to easily handle the large number of music files on a CD-ROM, you can organize them in folders (“albums”). The tracks of an album will be played in alphabetical order. If you want to arrange them in a ce

11、rtain order, let the file names start with numbers. For example: 001-ONEWORLD.MP3 002-FIRESTARTER.MP3 003-DEEP.MP3 GENERAL INFORMATION This set will play all albums in alphabetical order. An album name includes all folders in which the album is located, e. g. the album VERDI in CLASSIC has the album

12、 name CLASSICVERDI. The albums in the illustration will be played in the following way: CLASSIC1 CLASSICMOZART2 CLASSICVERDI3 POPBLUR4 REGGAE5 In POP there are no MP3 files. POP is therefore skipped. There may be an album 0 which will be played before all other albums. Album 0 contains all tracks wh

13、ich you did not put into an album. How to make a CD-ROM with MP3 Record (“burn”) the music files from your hard disc on a CD-ROM with your computers CD burner. Make sure that the file names of the MP3 files end with mp3 . When burning your MP3-CDs, use either ISO 9660 disc format or UDF. CD burning

14、software like “DirectCD” or others support the UDF format. ALBUM POWER SUPPLY/HEADPHONES Average battery lifetime of 1 alkaline battery ,type AA (LR6, UM3): Playback ofAudio disc MP3-CD ESP off (power-saving mode)6 hours5 hours ESP on6 hours3 hours Notes: Power-saving mode doubles your playtime. 20

15、seconds after pressing 9, the display switches off. After 90 seconds the set switches off automatically. POWER SUPPLY Mains adapter Only use the AY 3170 mains adapter (4.5 V/300 mA direct current, positive pole to the center pin). Any other product may damage the set. 1 Make sure the local voltage c

16、orresponds to the adapters voltage. If your mains adapter is equipped with a voltage selector, set this selector to the local mains voltage if necessary. 2 Connect the mains adapter to 4.5V DC on the set and to the wall outlet. Note: Always disconnect the adapter if you are not using it. HEADPHONES

17、Headphones (SBC HE205) Connect the supplied headphones to LINE OUT/p. Note:LINE OUT/pcan also be used for connecting this set to your HiFi system.To adjust the sound and volume, use the controls on the connected audio equipment and on the CD player. 5REGGAE .mp3 4BLUR .mp3 3VERDI .mp3 POP 2MOZART .m

18、p3 1CLASSIC .mp3 .mp3 GENERAL INFORMATION Supported formats This set supports: Disc format: ISO 9660, Joliet, Multisession, UDF, Enhanced Music CD, Mixed Mode CD Music file format: MP3 MP3 bit rate (data rate): 32320 kbps and variable bit rate Total number of music files and albums: around 350 (with

19、 a typical file name length of 20 characters) Note: The number of music files that can be played depends on the length of the file names. With short file names more files will be supported. Visit the EXPANIUMhomepage All trademarks used are owned by their respective owners. POWER SUPPLY Battery (not

20、 supplied) Inserting battery Open the battery compartment and insert 1 alkaline battery of type AA (LR6, UM3). Remove battery if it is empty or if the set will not be used for a long time. Indication of empty battery Replace the battery or connect the mains adapter as soon asblinks and battis displa

21、yed. Batteries contain chemical substances, so they should be disposed of properly. A INSTRUCTIONS FOR USE 1-4 POWER SUPPLY/HEADPHONES IMPORTANT! Hearing safety : Do not play your headphones at a high volume. Hearing experts advise that continuous use at high volume can permanently damage your heari

22、ng. Traffic safety : Do not use headphones while driving a vehicle. It may create a hazard and it is illegal in many countries. Even if your headphones are an open-air type designed to let you hear outside sounds, do not turn up the volume so high that you cannot hear what is going on around you. BA

23、SIC FUNCTIONS Playing a disc With this set you can play all pre-recorded audio CDs all finalized audio CDR(W)s MP3-CDs (CD-ROMs with MP3 ) 1 Push the OPEN 2 slider to open the CD lid. 2 Insert a disc, printed side up, by pressing gently on the discs centre so that it fits onto the hub. Close the lid

24、 by pressing it down. 3Press 2;to start playback. .yCd rEAd is displayed. Playback starts. Audio disc: The current track number and the elapsed playing time are displayed. MP3-CD: MP3 is shown. The current album number, track number and the elapsed playing time are dis- played. 4Press 9 to stop play

25、back. yAudio disc: The total number of tracks and the total playing time of the disc are displayed. yMP3-CD: The total number of albums and tracks are displayed. Note : If the total number of album is more than 9, the display will show “ ”; if the total number of tracks is more than 99, the display

26、will show “ ”. BASIC FUNCTIONS 5 To remove the disc, hold it by its edge and press the hub gently while lifting the disc. Note: After pressing 2;it may take some time until the first MP3 track is played. Playing Enhanced Music CDs and Mixed Mode CDs On Enhanced Music CDs and Mixed Mode CDs there are

27、 audio CD tracks as well as computer data (e. g. text files, pictures, MP3 files,). 1 Insert the disc and press 2;to start playback. yCd rEAd is displayed. Playback starts. All audio CD tracks will be played. 2 If there are MP3 and AAC files on the disc, MP3 blinks. Keep MODE pressed for 2 seconds t

28、o select MP3 playback. yCd rEAd is displayed. Playback starts with the first track of the first album. All MP3 will be played. 3 To return to audio CD playback, keep MODE pressed for 2 seconds. Note:To protect your headphones and your Hi-Fi system from damage, you will hear no sound when a computer

29、(data) file is played. Press to skip to the next track. Pause 1 Press 2; to interrupt playback. yThe time where playback was interrupted will blink. 2 To resume playback press 2; again. TITLEALBUM TITLEMP3 BASIC FUNCTIONS Volume and sound Volume adjustment Adjust the volume by using VOL E. Sound adj

30、ustment 1 Press DBB for a moderate bass enhancement . yis shown and dbb1 is displayed. 2 Press DBB again for a strong bass enhancement. yis shown and dbb2 is displayed. 3 Press DBB again to switch the bass enhancement off. .ydisappears. REMOTE CONTROL (SUPPLIED OR OPTIONALLY AVAILABLE) Use the AY 37

31、67 or AY 3768 cord remote control.The buttons on the remote control have the same functions as the corresponding buttons on the set. 1 Press 9 twice to switch off the set. 2 Firmly connect the remote control to LINE OUT/p on the set. 3 Adjust the volume VOL E on the CD player and remote control. DBB

32、 DBB DBB TITLE DBB BASIC FUNCTIONS Selecting and searching (on all discs) Selecting a track during playback Briefly press or once or several times to skip to the beginning of the current, previous or subsequent track. yPlayback continues with the selected track . Searching for a passage during playb

33、ack 1 Keep or pressed to find a particular passage in a backward or forward direction. ySearching is started and playback continues at a low volume. After 2 sec- onds the search speeds up. 2 Release the button at the desired passage. yNormal playback continues. Notes: DuringREPEAT, SHUFFLE, SHUFFLE

34、ALL, MP3or while playing a programme, searching is only possible within the current track. Selecting an album (on MP3-CDs only) Selecting an album during playback Briefly press or + once or several times to skip to the fi rst track of the current, previous or subsequent album. yThe fi rst track of t

35、he selected album is played. Selecting a track during playback 1 Keep - or + pressed to skip quickly to previous or subsequent MP3 tracks. ySkipping starts and speeds up after 2 seconds. 2 Release the button at the desired track. yPlayback continues with the selected track. Note: To skip from track

36、to track at low speed, use or . INSTRUCTIONS FOR USE 1-5 FEATURES Programming track numbers You can select up to 50 tracks and store them in the memory in a desired sequence. You can store any track more than once. 1 Select a track with or . 2 Press PROGRAM to store the track. yPROGRAMis shown and P

37、 with the number of stored tracks is displayed. 3 Select and store all desired tracks in this way. 4 If necessary, press 9 to stop normal playback. Press 2;to start playback of the programme. .yPlayback of the programme starts. To add additional tracks to your programme, press 9 to stop playing the

38、programme and continue with step 1. You can review the programme by pressing PROGRAM for more than 3 sec- onds. yAll stored tracks are displayed in sequence. Clearing the programme 1 If necessary, press 9 to stop playback. 2 Press 9 to clear the programme. yCLr is displayed, PROGRAMdisappears and th

39、e programme is cleared. If you press PROGRAMand there is no track selected, SEL is displayed Notes: The programme will also be cleared if you interrupt the power supply or open the CD lid or if the set switches off automatically. After storing 50 tracks, FULLis displayed. PROG TITLE PROG FEATURES St

40、oring the last position played-RESUME You can store the last position played. When restarting, playback continues from where you have stopped. 1 Switch the slider to RESUME during playback to activate RESUME. yRESUMEis shown. 2 Press 9 whenever you want to stop playback. 3 Press 2; to resume playbac

41、k. yPlayback continues from where you have stopped. To deactivate RESUME, switch the slider to OFF. yRESUMEdisappears. Locking all buttons-HOLD You can lock all buttons of the set. When you press any key, no action will be executed then. Switch the slider to HOLD to activate HOLD. yHOLDis shown and

42、all buttons are locked. When pressing any key, HoLd is displayed. To deactivate HOLD, switch the slider to OFF. yHOLDdisappears. OFF RE SUME HOLD TITLE RESUME HOLD TITLE FEATURES Selecting different playback possibilities-MODE It is possible to play tracks in random order or to repeat a track, an al

43、bum or an entire disc. 1 Press MODE repeatedly during playback to select either: SHUFFLE(with MP3-CDs only): All tracks of the current album are played in random order until all of them have been played once. SHUFFLE ALL: All tracks of the disc are played in random order until all of them have been

44、played once. SHUFFLE REPEAT(with MP3-CDs only): All tracks of the current album are played repeatedly in random order. SHUFFLE REPEAT ALL: All tracks of the disc are played repeatedly in random order. REPEAT: Audio disc: The current track is played repeatedly. MP3-CD: The current album is played rep

45、eatedly. REPEAT ALL: The entire disc is played repeatedly. When playing a programme, you can select either: SHUFFLE PROGRAM: All tracks of the programme are played in random order until all of them have been played once. SHUFFLE REPEAT PROGRAM: All tracks of the programme are played repeatedly in ra

46、ndom order. REPEAT PROGRAM: All tracks of the programme are played repeatedly. 2 Playback starts in the chosen mode after 2 seconds. 3 To return to normal playback, press MODE repeatedly until the display indication disappears. SHUFFLEREPEAT ALL TITLE FEATURES ESP-Electronic Skip Protection With a c

47、onventional portable disc player the music may stop e.g. while you are jogging.The ELECTRONIC SKIP PROTECTION protects this set against loss of sound caused by light vibrations or shocks. Continuous playback is ensured. ESP does not protect the set against damage caused by dropping ! Press ESP durin

48、g playback to activate the skip protection. yESP is shown and the protection is activated. To deactivate the skip protection, press ESP again. yESP disappears and the protection is deactivated. Beep sound A beep sound accompanies various key operations. Keep DBB pressed for more than 2 seconds to select your beep option. If the beep sound has been activated : ybEEP is display If the beep sound has been deactivated : yno bEEP is display ESP TITLE INSTRUCTIONS FOR USE 1-6 TROUBLESHOOTING WARNING: U