Philips-DVDR-3330-H-Service-Manual(1) 电路图 维修手册.pdf

《Philips-DVDR-3330-H-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-DVDR-3330-H-Service-Manual(1) 电路图 维修手册.pdf（161页珍藏版）》请在收音机爱好者资料库上搜索。

1、Published by KC-TE 0534 AV Systems Printed in the Netherlands Subject to modifi cation EN 3139 785 31150 DVDR3300H/02/05/19/51HDD a bar representing what is temporarily stored will appear with the recording marked in red,continue to press PREVIOUSto go back to the part of the recording you want to w

2、atch and the recorder will start playing from there. 2Press TUNERto go back to the liveTV broadcast. Tip You can pause and jump forward or backward of what you have already recorded without interfering with the recording. Recording to hard disk 1Press INFOand a bar representing what is temporarily s

3、tored will appear. 2Press PREVIOUSor NEXTto search for where you want to start recording. Tip You can also press JUMP BACK, JUMP FWDor press and hold PREVIOUS,NEXT. 3Press REC. 4Key in the time period to record or press RECagain for a 30 minutes recording. Tip Each time you press RECanother 30 minut

4、es recording time is added. Troubleshooting For more troubleshooting tips,see the user manual. ProblemTip Remote control Aim remote control at recorder (notTV) or remove any obstacles in the way. Batteries are weak;replace the batteries. Disc does not play The child lock is on.Refer to user manual t

5、o unlock it. Wrong region code.The DVD must be coded forALL regions or Region 2. Check if the disc is defective,scratched or warped.Clean the disc or try another disc. The picture is distorted The disc does not match theTV colour system standard (PAL/NTSC). When playing DVD set Record Mode to high-q

6、uality speed to improve picture quality. Recordings are not Channel you are recording is not stored or the wrong programme number is selected. occurring as scheduled. If you adjust the clock after you set a timer recording,reset the timer recording. New recordings cannot The recorder cannot duplicat

7、e copyrighted material onto a recordable DVD. be made. A finalised DVD+R has been inserted.Change disc. Need help? User Manual See the user manual that came with your hard disk/DVD recorder Online Go to Koninklijke Philips N.V. All rights reserved. 12 NC 31 39 246 17151 Quick Start Guide DVDR 3300H

8、DVDR 3330H DVDR 5330H Hard Disk/DVD Recorder User manual Hard disk/DVD recorder RF coaxial cableSCART cableQuick start guide Remote control and 2 batteries 3.Directions For Use EN 83139 785 31150 AUDIO / VIDEO OUTDIGITAL AUDIO OUT SCART IN If you have aVCR,follow the instructions forConnection withV

9、CR or similar device, if you dont have aVCR follow the instructions forConnection withoutVCR. Television (back) Hard disk/ DVD recorder (back) To antenna or set-top box Remote Control (back) Hard disk/DVD recorder (front) STANDBY-ON Please Choose Settings Audio Subtitle Menu Country TV Shape English

10、 English English Austria 4:3 PanScan Press SETUP to continue 10 :37 09:2415:24 09:2415:24 2:0 0 00:29:30 SP+ 2005-03-26 19:30:10 PAL Recorded title list TELET 2005-03-26 19:30:10 P042005-03-28 09:00:00 TELET 2005-03-28 17:20:30 P162005-03-30 17:00:00 TELET 2005-03-30 11:10:10 Pressto edit title or P

11、LAY/OK keys for playback VCR or similar device (back) AUDIO / VIDEO OUTDIGITAL AUDIO OUT SCART IN Television (back) Hard disk/ DVD recorder (back) To antenna or set-top box Finding the viewing channel 1Press STANDBY-ON on the recorder. 2Switch on theTV. Tip If connected to yourVCR,make sure theVCR i

12、s switched off or in standby mode before proceeding. 3Press0 on theTVs remote control,then press the Channel Down button repeatedly until you see the General Setup page.This is the correct viewing channel for the recorder. Tip You may press theAV or SELECT button on the TVs remote control (if availa

13、ble) to select the correct viewing channel. See yourTVs user manual. Connection withVCR or similar device Before connecting Your new Philips hard disk/DVD recorder can replace theVCR for all your recording needs, just unplug all the connections from yourVCR. Connecting 1Follow steps 1 to 4 ofConnect

14、ing under Connection withoutVCR to connect the recorder before you proceed to step 2 below. 2Connect another SCART cable (not supplied) into the EXT2AUX I/O SCART socket at the rear of the recorder. 3Connect the other end into the SCART OUT socket at the rear of yourVCR. 4Plug in the power cable fro

15、m yourVCR to an AC power outlet. Connection withoutVCR Before connecting YourTV should be connected to the cable box/set-top box,satellite receiver or aerial, unplug the antenna cable from theTV. Connecting 1Connect the antenna cable (plugged out from theVCR orTV) to theANTENNAsocket at the rear of

16、the recorder. 2Connect the supplied RF coaxial cable into theTVsocket at the rear of the recorder and into theAntenna In socket of theTV. 3Connect the SCART cable to the SCART IN socket of theTV and to the EXT1 socket at rear of the recorder. 4Plug in the power cable from the recorder to anAC power

17、outlet. Conduct installation 1Select yourAudio Language,Subtitle Language, Menu Language,Country andTV Shape. Tip Use the recorders remote control to make your choice. 2Press SETUPto save and you are now prompted to connect the antenna. 3Activate automatic Channel Search. Tip If no channels were fou

18、nd,check the antenna connection and refer to user manual to search again once installation is done. 4Check Date andTime. 5Press SETUPto finish installation. Inserting batteries Note In this setup theVCR cannot record TV programmes. Pause LiveTV Sometimes you might be interrupted while watch- ing you

19、r favourite programme.Now you can PAUSE it,as if you were in control of the broadcast. 1Press PAUSEwhile watching any liveTV programme to suspend it. 2Press PLAYto continue. Tip When the recorder is switched on,the programme you are watching is temporarily recorded.In Pause LiveTV the recorder repla

20、ys the recorded footage,which will be erased when the recorder is switched to standby. 3Press TUNERto go back to live broadcast. Record 1Press RECto record. 2Key in the amount of time to record or press RECagain for a 30 minutes recording. Tip Every time you press RECan additional 30 minutes is adde

21、d to the recording time. 3Press STOPto stop the recording. Playback from hard disk 1Press HDDto see the titles on hard disk. 2Press UPor DOWNto select a title. 3Press PLAYon the title you want. Note where the positive and negative ends go. 3.Directions For Use EN 93139 785 311504.Mechanical Instruct

22、ions 4. Mechanical Instructions Note: The position numbers given here refers to the Exploded view on chapter 10. 4.1 Dismantling of the DVD Tray cover 1) Insert a screw-driver into the slot provided at the bottom of the set and push in the direction as shown in picture 4-1 to unlock before sliding t

23、he Tray cover assembly 910 out. Figure 4-1 2) Remove the Tray cover assembly 910 as shown in Figure 4-2. Figure 4-2 4.2 Dismantling of the Front Panel assembly 1) Remove 7 screws 220+240 to loosen Top cover 196. 2) Remove the DVD Tray cover as given in step 4-1. 3) Loosen the Digital Board 1001 Wron

24、g user input 40202 Address is not dividable by 4 Example DS: 402 0 xa1000010 0 xad112222 040200: Test OK Nucleus Name DS_SDRAM_Read Nucleus Number 403 Description Read from a specific un-cached memory address Technical -Decode the user input and check the ranges -Read from the SDRAM and return this

25、info to the user Execution Time Less than 1 second User Input The location from which the data must be read (SDRAM starts at address 0 xA0000000) Error Number Description 40300 Reading from the SDRAM succeeded 40301 Reading from the SDRAM failed; Wrong user input 40302 Address is not dividable by 4

26、Example DS: 403 0 xa1000010 040300: Value read = 0 xAD112222 Test OK Nucleus Name DS_SDRAM_DmaWriteRead Nucleus Number 404 Description Write a pattern to the entire SDRAM using DMA and check the data Technical -Check if the Stack pointer is not in the write range -Clear a 64kb block and then fill it

27、 with a pattern -Initialise the DMA controller and write the data to the SDRAM -Then check if all the data was written correctly (except descriptor tables) -Repeat the process 4 times with 4 different patterns Execution Time 24 seconds User Input None. Error Number Description 40400 Writing to the S

28、DRAM succeeded 40401 Stack area definition ERROR! 40402 DMA controller could not be initialised. 40403 Not all data was transferred correctly Example DS: 404 040400: Test OK EN 263139 785 31150Firmware Upgrading Wrong user input 50202 Address is not dividable by 4 Example DS: 502 0 xb8000000 050200:

29、 Value read = 0 x3C08A000 Test OK EN 273139 785 311505.Firmware Upgrading & Diagnostic Software Nucleus Name DS_FLASH_ChecksumProgram Nucleus Number 503 Description Check the checksum of the application partitions by recalculating and comparing partition checksums Technical -Determine the number of

30、segments -Find the application in each segment and determine its checksum -Check whether the checksums stored match the newly calculated Execution Time 6 seconds User Input None Error Number Description 50300 The checksum is valid, the test succeeded 50301 The checksum is invalid Example DS: 503 050

31、300: BootCode checksum is: 0 xBABE5B6F, which is correct Diagnostics checksum is: 0 xBABEBAFF, which is correct Download checksum is: 0 xBABEEDBF, which is correct Application checksum is: 0 xBABE8EEC, which is correct Test OK Nucleus Name DS_FLASH_CalculateChecksum Nucleus Number 504 Description Ca

32、lculate the checksum over all memory addresses. Used to check entire FLASH contents Technical -Run the checksum calculation algorithm on all flash memory addresses Execution Time 6 seconds User Input None Error Number Description 50400 Calculating the checksum over all addresses succeeded Example DS

33、: 504 050400: The Checksum = 0 xBABE30A4 Test OK Nucleus Name DS_FLASH_CalculateChecksumFast Nucleus Number 505 Description Calculate a checksum over a selected number of address locations Technical -Run the checksum calculation algorithm on a selected number of flash memory addresses Execution Time

34、 6 seconds User Input None Error Number Description 50500 Calculating the checksum over selected addresses succeeded Example DS: 505 050500: The Checksum = 0 xBABEB064 Test OK Video Input Processor (VIP) Nucleus Name DS_VIP_DevTypeGet Nucleus Number 600 Description Get the device (revision) type inf

35、ormation of the VIP IC Technical -Initialise IIC -Read out the device (revision) type information of the VIP IC Execution Time Less than 1 second User Input None Error Number Description 60000 Getting the information from the VIP succeeded 60001 The IIC bus initialisation failed 60002 The was an err

36、or getting the information from the VIP 60003 Type not according to type stored in HW diversity string Example DS: 600 060000: Found SAA7118 Test OK EN 283139 785 31150Firmware Upgrading & Diagnostic Software5. Nucleus Name DS_VIP_Communication Nucleus Number 601 Description Check the communication

37、between the IIC controller of the Codec and the VIP IC Technical -Initialise IIC -Read data from a location in the VIP Execution Time Less than 1 second User Input None Error Number Description 60100 Communicating with the VIP succeeded 60101 The IIC bus was not accessible 60102 There was a timeout

38、reading the device 60103 The IIC acknowledge was not received 60104 The communication with the device failed 60105 The IIC bus initialisation failed Example DS: 601 060100: Test OK Nucleus Name DS_VIP_ClockOutputOn Nucleus Number 602 Description Switch the clock output on Technical -Initialise IIC -

39、Set the clock output through IIC Execution Time Less than 1 second User Input None Error Number Description 60200 Switching the clock output on succeeded 60201 Switching the clock output on failed Example DS: 602 060200: Test OK Nucleus Name DS_VIP_ClockOutputOff Nucleus Number 603 Description Switc

40、h the clock output off Technical -Initialise IIC -Reset the clock output through IIC Execution Time Less than 1 second User Input None Error Number Description 60300 Switching the clock output off succeeded 60301 Switching the clock output off failed Example DS: 603 060300: Test OK EN 293139 785 311

41、505.Firmware Upgrading & Diagnostic Software Nucleus Name DS_VIP_SelectInput Nucleus Number 604 Description Select an input video path to be switched to the analogue output pin (AOUT) of the VIP Technical -Check the user input -Initialise IIC -Read out the VIP id -Write the set of registers required

42、 for the input specified Execution Time Less than 1 second User Input The input to select, see table below. Available channels for input of the 7118 and their description: Channel number Description 1 CVBS_Y_IN_A 2 CVBS_OUT_B 3 CVBS_Y_IN_B 4 CVBS_Y_IN_C 6 C_IN 8 G_IN 9 Y_IN 13 B_IN 14 U_IN 18 R_IN 1

43、9 V_IN Available channels for input of the 7115 and their description: Channel number Description 1 CVBS_Y_IN_B 2 CVBS_OUT_B_VIP 4 C_IN_VIP 7 CVBS_Y_IN_B Available channels for input of the 7119 and their description: Channel number Description 1 Y / CVBS 3 CVBS 4 Y3 6 C / CVBS 8 G 9 Y 12 Y2 13 B 14

44、 U 17 C 18 R 19 V Available channels for input of the 7173 and their description: Channel number Description 1 CVBS_TUNER_IN 2 CVBS_REAR_IN 3 CVBS_FRONT_IN 4 C_REAR_IN 5 Y_REAR_IN 6 Y_FRONT_IN 7 C_FRONT_IN 8 AL_REAR_IN 9 AL_FRONT_IN 10 AR_FRONT_IN 11 AR_REAR_IN 12 SIF_TUNER_IN EN 303139 785 31150Fir

45、mware Upgrading & Diagnostic Software5. Error Number Description 60400 Selecting the input of the VIP succeeded 60401 The user provided wrong input 60402 The VIP was not accessible 60403 An unsupported VIP was found Example DS: 604 1 060400: Test OK Digital Video Input Output Circuit (DVIO) Nucleus

46、Name DS_DVIO_LinkDevTypeGet Nucleus Number 700 Description Get the device (revision) type information of the 1394 Link layer IC Technical -Initialise the PIO pins on the Codec -Read out the ID register Execution Time Less than 1 second User Input None Error Number Description 70000 Getting the infor

47、mation from the link layer IC succeeded 70001 Getting the information from the link layer IC failed 70002 Type not according to type stored in HW diversity string Example DS: 700 070000: Device type of the link layer IC: ffc00301 Test OK Nucleus Name DS_DVIO_PhyDevTypeGet Nucleus Number 701 Descript

48、ion Get the device (revision) type information of the 1394 Physical layer IC Technical -Initialise the PIO pins of the Codec -Write the PHY-access register in the Link chip to indicate phy read access -Wait until the link chip has obtained the value from the phy-chip -Read this out and filter the da

49、ta to be returned to the user Execution Time Less than 1 second User Input None Error Number Description 70100 Getting the information from the physical layer IC succeeded 70101 The physical layer IC was not accessible 70102 Getting the information from the physical layer IC failed 70103 Type not according to type stored in HW diversity Example DS: 701 070100: Physical layer IC: VendorID: 0 x006037, ProductID: 0 x412801 Test OK Nucleus Name DS_DVIO_LinkCommunication Nucleus Number