Philips-HTS-3610-K-Service-Manual(1) 电路图 维修手册.pdf

《Philips-HTS-3610-K-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-HTS-3610-K-Service-Manual(1) 电路图 维修手册.pdf（39页珍藏版）》请在收音机爱好者资料库上搜索。

1、Published by KC-TE 0519 AV Systems Printed in the Netherlands Subject to modifi cation EN 3139 785 31630 HTS3300K/51 fr Reparaturen sind Original-Ersatzteile zu verwenden. Sicherheitsbauteile sind durch das Symbol ! markiert. I Le norme di sicurezza esigono che lapparecchio venga rimesso nelle condi

2、zioni originali e che siano utilizzati i pezzi di ricambio identici a quelli specificati. Componenty di sicurezza sono marcati con ! GB After servicing and before returning set to customer perform a leakage current measurement test from all exposed metal parts to earth ground to assure no shock haza

3、rd exist. The leakage current must not exceed 0.5mA. EN 73139 785 31630Measurements Setup, Service Aid & Lead Free Requirements2. 2.1 Lead Free Requirements Pb(Lead) Free Solder When soldering , be sure to use the pb free solder. INDENTIFICATION: Regardless of special logo (not always indicated) one

4、 must treat all sets from 1 Jan 2005 onwards, according next rules: Important note: In fact also products of year 2004 must be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this. Due to lead-free

5、technology some rules have to be respected by the workshop during a repair: Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment. In general use of solder-paste within workshops

6、should be avoided because paste is not easy to store and to handle. Use only adequate solder tools applicable for lead-free solder alloy. The solder tool must be able o To reach at least a solder-temperature of 400C, o To stabilize the adjusted temperature at the solder-tip o To exchange solder-tips

7、 for different applications. Adjust your solder tool so that a temperature around 360C 380C is reached and stabilized at the solder joint. Heating- time of the solder-joint should not exceed 4 sec. Avoid temperatures above 400C otherwise wear-out of tips will rise drastically and fl ux-fl uid will b

8、e destroyed. To avoid wear-out of tips switch off un-used equipment, or reduce heat. Mix of lead-free solder alloy / parts with leaded solder alloy / parts is possible but PHILIPS recommends strongly to avoid mixed solder alloy types (leaded and lead-free). If one cannot avoid or does not know wheth

9、er product is lead- free, clean carefully the solder-joint from old solder alloy and re-solder with new solder alloy (SAC305). Use only original spare-parts listed in the Service-Manuals. Not listed standard-material (commodities) has to be purchased at external companies. Special information for BG

10、A-ICs: - always use the 12nc-recognizable soldering temperature profi le of the specifi c BGA (for de-soldering always use the lead-free temperature profi le, in case of doubt) - lead free BGA-ICs will be delivered in so-called dry- packaging (sealed pack including a silica gel pack) to protect the

11、IC against moisture. After opening, dependent of MSL- level seen on indicator-label in the bag, the BGA-IC possibly still has to be baked dry. (MSL=Moisture Sensitivity Level). This will be communicated via AYS-website. Do not re-use BGAs at all. For sets produced before 1.1.2005 (except products of

12、 2004), containing leaded solder-alloy and components, all needed spare-parts will be available till the end of the service-period. For repair of such sets nothing changes. On our website www.atyourservice.ce.P you fi nd more information to: ? BGA-de-/soldering (+ baking instructions) ? Heating-prof

13、i les of BGAs and other ICs used in Philips-sets You will fi nd this and more technical information within the “magazine”, chapter “workshop news”. For additional questions please contact your local repair-helpdesk. EN 83139 785 316303.Directions For Use 3. Directions For Use The following except of

14、 the Quick Use Guide serves as an introduction to the set. The Complete Direction for the Use can be downloaded in different languages from the internet site of Philips Customer care Center: QUICK START GUIDE 12nc: 3139 246 19201 HTS3300K 1whats in the box 2connect TV 3connect subwoofer, speakers an

15、d antennas 3a Placement of speakers 3c Connect the FM and MW antennas REAR LREAR R FRONT L CENTER FRONT R Subwoofer TV 3b Connect the speakers and subwoofer to the DVD system (refer to the user manual for “Individual speaker volume adjustment”) 3d Connect the mains cord to the power supply Pb PrY L

16、R FRONT RFRONT L REAR RREAR L CENTER Note:For connecting to a Progressive Scan TV, refer to the user manual for proper connections and detailed set up. A Remote control includes 2x AA batteries D B GH C Subwoofer FM wire antenna MW loop antenna Main unit Front/Rear/Center speakers Video cableE Audio

17、 cable F A H G E A Y Pb Pr cables not supplied OR EN 93139 785 31630Directions For Use3. 4play a disc DISC 4a Press DISC. Point the remote control towards the DVD system. 4b Load in a disc Press OPEN CLOSE to open and close the disc tray. 4c Select correct AV In channel Switch to the correct input s

18、ource by using the TV remote control. GET PICTURE Check the connection of the DVD system to TV is in place (see 2 Connect TV). Check the AV mode on TV. It may be called FRONT, A/V IN, or VIDEO. Choose the different modes using TV remote control. Or, use the TV remote control to select Channel 1 on T

19、V, then press Channel down button until you get the picture. See your TV manual for more details. Refer to chapter “DVD Setup Menu Options” in the user manual for detailed descriptions. More settings and featuresGET SOUND To enhance the sound quality Press SOUND button to select a predefined digital

20、 sound effect. Detailed playback features and additional functions are described in the user manual. No sound from rear speakers? Press SURR button to select “Multi-Channel”. 5programme radio stations NEEDS HELP? Visit our website 5a Press TUNER. 5b Press and hold PLAY 2 until“START .” appears. It w

21、ill start to programme all available radio stations. 5c Once complete, use S / T to select a preset radio station. Note: This feature is only available for first time setup. 6connect other device (optional) AUDIO OUT Pb PrY L R Audio/Video device Note:Connect the AUDIO OUTPUT of other audio/video de

22、vice to this DVD system in order to use the Home Theatre Audio Systems surround sound capabilities. Press AUX/DI on the remote control in order to listen to the playback. EN 103139 785 316303.Directions For Use Quick Start Guide HTS 3610KHomeTheatre System DVD system Rear speakers (left & right) Rem

23、ote control and 2 batteries Quick start guideCentre speaker Subwoofer Front speakers (left & right) Whats in the Box Audio cables (red & white plugs) Video cables (yellow plug) AM/MW loop antenna FM wire antenna User manual Connect Speakers & Subwoofer to DVD System Connect the various coloured plug

24、s from the speakers and subwoofer to the same colour socket on the rear of DVD system. FixAntennas 1 Connect the FM antenna to the FM socket, extend the antenna and fix it on the wall. DVD System (back) 2 Unfold theAM/ MW loop antenna and fix the claw into the slot. 3 Push back tab and insert each w

25、ire into slot. Position Speakers & Subwoofer 1 Place centre speaker on or close to theTV. 2 Place subwoofer on the floor. 3 Place front speakers equal distance from the TV and angle them 45 degree to the listener. 4 Place rear speakers facing the listener,equal distance on the left and right. MW loo

26、p antenna DVD System (back) Rear Speaker (left) Rear Speaker (right) Front Speaker (right) Front Speaker (left) Centre Speaker DVD System (back) Sub-Woofer EN 113139 785 31630Directions For Use3. Insert Batteries in Remote Control 1 Remove batteries compartment cover. 2 Insert the provided batteries

27、 in the remote control.Take note of where the positive and negative ends should go. 3 Replace the batteries compartment cover. Remote Control (back) Find CorrectViewing Channel 1 Press STANDBY-ONon the DVD systems remote control. 2 Press DISCon the remote control until DISC appears on the front pane

28、l. 3 Switch on theTV. 4 Press0 on theTVs remote control, then repeatedly press the Channel Down button until you see the DVD background screen. This is the correct viewing channel for the home theatre system. Tip For someTVs,to find the correct viewing channel,you can keep pressing theAV or the SELE

29、CT buttons.If still unable to find the correct viewing channel,check the connections again or check yourTVs user manual. Connect DVD system toTV 1 Use the yellowVideo cable to connect the yellow CVBS socket on the rear of the DVD system and the yellowVIDEO IN jack at the rear of theTV. 2 Plug in the

30、 power cable of the DVD system to anAC outlet. Tip To connect other devices to the DVD system,refer to the use manual. To antenna or set-top box ConnectAudio fromTV to DVD System (Optional) Use the red & white audio cables to connect the red & whiteTV-IN sockets on the rear of the DVD system and the

31、 red & whiteAUDIO OUT sockets on theTV. DVD System (back) Television (back) DVD System (back) Television (back) Tip SomeTVs may not have anAUDIO OUT jack. VIDEO IN (CVBS) VIDEO IN (CVBS) VIDEO OUT (CVBS) VIDEO OUT (CVBS) AUDIO OUT AUDIO IN Need help? User Manual For more product information refer to

32、 the user manual of the home theatre system. Online Go to Koninklijie Philips N.V. All rights reserved. 12 NC 31 39 246 19171 Troubleshooting For more troubleshooting tips,see the user manual. ProblemTip No power Check if theAC power cord is properly connected. Press the STANDBY-ON on the front of t

33、he DVD system to turn on the power. No picture Press DISC on remote control. Check connection toTV and ensure the plugs are firmly in place. No sound or Adjust the volume. distorted sound Check the speaker connections and settings. Check audio connections and press SOURCE button to select the correc

34、t input source. Remote control Check that the batteries are loaded correctly or replace the batteries with new ones. does not work Select the source (DISC orTUNER,for example) before pressing the function button. Reduce the distance between the remote control and the system. Point the remote control

35、 directly toward the IR sensor. Listen to Radio 1 Press TUNER. 2 Press and hold PLAYuntilSTART appears. Tip This feature is only available for first time setup,refer to user manual if you wish to program radio stations again or for manual programming. 3 Once completed you can use NEXTor PREVIOUSto s

36、elect a radio station. Front display Play DVD 1 Press OPEN/CLOSEon the front of the DVD system to open the disc tray. 2 Place DVD in tray with the label facing up. 3 Press OPEN/CLOSEagain. 4 Press UP, DOWN,RIGHTor LEFTto scroll through the options in the DVD menu. 5 Press PLAYon the option you want.

37、 6 To stop press STOP. Tip Press PLAYto resume from where you stopped or press STOPand PLAY to start from the beginning of the title. 7 Press DISC MENUto go back to the DVD menu. DVD Player (front) Experience Surround Sound 1 Press SURRto switch between Stereo and Multi-channel. 2 Press SOUNDfor eit

38、her Concert,Drama, Action or Sci-fi preset digital sound effects. EN 123139 785 316304.Dismantling Instructions & Service Positions D Figure 4-4 C E 4.2 Dismantling of the Tuner Module, MONO Board, Front Board, PSU Module 1) Loosen 1 screw A (see Figure 4-3) to remove the Tuner Module (pos 1040). 2)

39、 Loosen 9 screws B (see Figure 4-3) and 4 screws (see Figure 4-4) to remove MONO Board. 3) Release 4 snap hooks to remove Front Board. - 1 snap hook each on the left & right side (pos 161). - 2 snap hooks on the bottom side (pos 161). 4) Loosen 4 screws E (see Figure 4-4) to remove the PSU Module. 4

40、. Dismantling Instructions 4.1 Dismantling of the DVD Loader 1) The tray can be manually open by inserting a minus screw drive and push the lever in the direction as shown in Figure 4-1 to unlock the tray before sliding it out. Figure 4-1 2) Slide out the tray and remove the Cover Tray (pos 110) as

41、shown in Figure 4-2. Figure 4-2 3) Loosen 5 screws to remove the Front Top.(pos 240) - 1 screw each on the left & right side (pos 272) - 3 screws behind 4) Loosen 4 screws C (see Figure 4-4) to remove the DVD Loader. BB B A Figure 4-3 EN 133139 785 316304.Dismantling Instructions & Service Positions

42、 4.3 Service Positions Mono Board Thick Insulation Sheet Front Board Thick Insulation Sheet PSU Board DVD Loader EN 143139 785 316305.Service Test Program 5. Service Test Program TESTActivated withACTION EEPROM FORMAT TEST to Exit Load default data. Display shows “NEW”. Caution! All presets from the

43、 customer will be lost! ROTARY ENCODER TEST Volume Knob Display shows value for 2 seconds. Volume values increases or decreases in steps of 1 until 0 (VOL MIN) or 40 (VOL MAX) is reached. LEAVE SERVICE TEST PROGRAM Disconnect mains cord LX8300SA & LX8320SA & LX8500W_Service Test Program_dd wk0429 To

44、 start service test program open the tray with remote control or front panel key, while plugging in the mains cord press 2, 5 8 on remote control, the tray will close by itself and the set will display shown “S-Vxx-yy” Display shows “SERVICE” followed by ROM version “S-Vxx-yy” S refers to Service Mo

45、de V refers to Version xx refers to Software version number of BEA (counting up from 01 to 99) yy refers to Software version number of Front uP (counting up from 01 to 99) 5.1 Display Test Purpose: This test is used to check the driving circuits, the display and whether there are any short-circuits,

46、 open-circuits or any other defects. Player: Following display patterns are used to test the display and its connections to P. Pattern 1: Default: All display control pins are ON - to check the open-circuits Pattern 2: Alternate display control pins are on (Test Pattern: 0 x55) - to check the short-

47、circuits on Data port Receiver: Following display patterns are used to test the display and its connections to P. Pattern 1: Default: All display control pins are ON - to check the open-circuits Pattern 2: Alternate display control pins are on (Test Pattern: 0 x55) - to check the short-circuits on D

48、ata port key DisplayTest triggered? n y Activate and display Pattern1 key DisplayTest triggered? n y Activate and display Pattern2 Main Menu Display Test key triggered? n y EN 153139 785 316305.Service Test Program 5.1.1 Reprogramming of DVD version Matrix After repair, the customer setting and regi

49、on code may be lost. Reprogramming will put the set back in the state in which it has left the factory, ie. with the default setting and the allowed region code. Model Region Region Code TV Type HTS 3300K Russia 5 PAL HTS 3500KRussia 5 PAL HTS 5310KRussia 5 PAL HTS 3610KRussia 5 PAL To reprogram do as follows: 1) Power up the set and select DISC source. 2) Open tray by press “OPEN/CLOSE” button on the set or press and hold “STOP” button on the