Philips-DVP-5900-Service-Manual(1) 电路图 维修手册.pdf

《Philips-DVP-5900-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-DVP-5900-Service-Manual(1) 电路图 维修手册.pdf（30页珍藏版）》请在收音机爱好者资料库上搜索。

1、Published by BB 0549 Service Audio Printed in the Netherlands Subject to modifi cation 3139 785 31770 DVP5900/12/05/37/98/93DVD Player CLASS 1 LASER PRODUCT 1 Technical Specifi cations and Connection Facilities .2 2 Measurements Setup, Service Aid fr Reparaturen sind Original-Ersatzteile zu verwende

2、n. Sicherheitsbauteile sind durch das Symbol ! markiert. I Le norme di sicurezza esigono che lapparecchio venga rimesso nelle condizioni originali e che siano utilizzati i pezzi di ricambio identici a quelli specificati. Componenty di sicurezza sono marcati con ! GB After servicing and before return

3、ing set to customer perform a leakage current measurement test from all exposed metal parts to earth ground to assure no shock hazard exist. The leakage current must not exceed 0.5mA. EN 73139 785 31770Measurements Setup, Service Aid & Service Hints2. 2.2 Service Hints CAUTION CHARGED CAPACITORS ON

4、THE SERVO BOARD MAY DAMAGE THE DRIVE ELECTRONICS WHEN CONNECTING A NEW DRIVE.THATS WHY, BESIDES THE SAFETY MEASURES LIKE SWITCH OFF POWER SUPPLY ESD PROTECTION ADDITIONAL ACTIONS MUST BE TAKEN BY THE REPAIR TECHNICIAN. The following steps have to be done when replacing the defective loader : 1. Dism

5、antling of the loader to access the ESD protection point if necessary. 2. Solder the ESD protection point*. 3. Disconnect fl exfoil cable from the defective loader. 4. Put a paper clip on the fl exfoil to short-circuit the contacts (fi g.1) 5. Replace the defective loader with a new loader. 6. Remov

6、e paperclip from the fl exfoil and connect it to the new loader. 7. Remove solder joint on the ESD protection point. ATTENTION: The laser diode of this loader is protected against ESD by a solder joint which shortcircuits the laserdiode to ground. For proper functionality of the loader this solder j

7、oint must be remove after connection loader to the set. Type 1 Type 2 (ESD protection point is accessible from top of loader) (ESD protection point is accessible from bottom of the loader) *Only applicable for defective loader needed to be sent back to supplier for failure analysis and to support ba

8、ckcharging evidence. This is also applicable for all partnership workshops. EN 83139 785 317703.Directions For Use 3. Directions For Use The following except of the Quick Use Guide serves as an introduction to the set. The Complete Direction for the Use can be downloaded in different languages from

9、the internet site of Philips Customer care Center: DivX DVD PlayerDVP5900 See, hear, play everything with HDMI Be impressed with this Philips DVD player with HDMI digital video and audio connection. Step into another home entertainment arena as you immerse yourself with High Definition video (720p /

10、 1080i). Unrivalled video performance HDMI out for digital high-definition video and digital audio Video Upscaling for improved resolution of up to 1080i lines Displays high definition pictures (JPEG) in true resolution Enrich your movie experience Progressive Scan for razor-sharp and flicker free i

11、mages 192kHz/24-bit audio DAC delivers high-quality audio Plays it all Movies: DVD, DVD+R/RW, (S)VCD, DivX 3.11/4.x/5.x/6.x, MPEG4 Music: CD, MP3-CD, CD-R/RW & Windows Media Audio Photos: Picture CD (JPEG) EN 93139 785 31770Directions For Use3. DivX DVD Player Technical specificationsProduct highlig

12、hts Picture/Display D/A converter: 10 bit, 54 MHz Picture enhancement: Progressive Scan, Video upscaling, Video upsampling Sound D/A converter: 192kHz/24-bit Signal to noise ratio: 108 dB Distortion and Noise (1kHz): 80 dB Crosstalk (1kHz): 100 dB Dynamic Range (1kHz): 94 dB Sound System: Dolby Digi

13、tal, MPEG2, Stereo Sound Enhancement: Night Mode Video Playback Disc Playback Media: CD, CD-R/CD-RW, Video CD/SVCD, DVD, DVD-RW (Video mode), DVD-R, DVD-Video, DivX, WMA, DVD+R/ +RW Compression formats: MPEG1, MPEG2, MPEG4, XviD, DivX 3.11, DivX 4.x, DivX 5.x Audio Playback Disc Playback Media: CD,

14、MP3-CD, WMA, CD- R/RW Compression format: Dolby Digital, MP3, PCM, Windows Media (TM) Audio MP3 bit rates: 32 - 256 kbps Still Picture Playback Disc Playback Media: Picture CD Picture compression format: JPEG Picture enhancement: Rotate, Zoom, High Definition Resolution Connectivity Other connection

15、s: HDMI out Audio Output - Analog: Stereo (Red/White cinch) Audio Output - Digital: Coaxial (cinch) Video Output - Analog: Component RGB (SCART), Composite CVBS (on SCART), Component Y Pb Pr (cinch), Composite CVBS (yellow cinch) Convenience On-Screen Display languages: Danish, Dutch, English, Frenc

16、h, German, Italian, Norwegian, Portuguese, Spanish, Swedish, Turkish, Polish, Russian Power Power supply: 100-240VAC, 50/60Hz Standby power consumption: 3W Accessories Batteries: Cables: None Remote control: 3141 017 90221 User Manual: Danish, Dutch, English, Finnish, French, German, Greek, Italian,

17、 Norwegian, Portuguese, Spanish, Swedish, Turkish, Polish, Russian Included batteries: 2x Longlife AA Dimensions Packaging dimensions (W x H x D): 562 x 85 x 411 mm Weight incl. Packaging: 3.5 kg Set dimensions (W x H x D): 435 x 48 x 310 mm Set weight: 1.9 kg HDMI HDMI stands for High Definition Mu

18、ltimedia Interface. It is a direct digital connection that can carry digital HD video as well as digital multichannel audio. By eliminating the conversion to analog signals it delivers perfect picture and sound quality, completely free from noise. HDMI is fully backward-compatible with DVI. Video Up

19、scaling With Video Upscaling you can increase the resolution of SD (Standard Definition) video signals that DVD uses to HD (High Definition) so youll be able to see more details thanks to a sharper, more true-to-life picture.The resulting HD video output signal can be fed to an HD display through HD

20、MI (High-Definition Multimedia Interface). High definition pictures With High Resolution JPEG playback, you can show up to 2 Megapixel resolution on your FTV. Now you can view your digital pictures in their true resolution, without loss of quality or details. Progressive Scan Progressive Scan double

21、s the vertical resolution of the image resulting in a noticeably sharper picture. Instead of sending a field comprising the odd lines to the screen first, followed by the field with the even lines, both fields are written at one time. A full image is created instantaneously, using the maximum resolu

22、tion. At such a speed, your eye perceives a sharper picture with no line structure. 192kHz/24 bit audio DAC 192KHz sampling enables you to have an accurate representation of the original sound curves. Together with a 24-bit resolution, more information is captured from the original analogue sound wa

23、ve form, giving a much richer audio reproduction. Multi-format Movies-DivX, MP4 Multi-format playability allows you to play most disc formats for maximum compatibility and viewing pleasure. Music: Windows Media Audio Multi-format playability allows you to play most disc formats for maximum disc comp

24、atibility and listening pleasure. Picture CD (JPEG) Multi-format playability allows you to view images in the comfort of your living room and play most disc formats for maximum disc compatibility and viewing pleasure. EN 103139 785 317704.Dismantling Instructions & Service Positions 3) Loosen 5 scre

25、ws to remove the Cover Top. - 1 screw each on the left and right side - 3 screws on the rear 4) Loosen 4 screws to remove the DVD Loader as shown in Figure 3. Figure 4-3 4. Dismantling Instructions 4.1 Dismantling of the DVD Loader. 1) The tray can be manually open by inserting a minus screw driver

26、and push the lever in the direction as shown in Figure 1 to unlock the tray before sliding it out. 2) Slide out the tray and remove the Tray Front assembly as shown in Figure 2. Figure 4-1 Figure 4-2 AA EN 113139 785 317704.Dismantling Instructions & Service Positions 4.2 Dismantling of the Front Bo

27、ard, Zoran Board, PSU Board. 1) Release 2 snap hooks on the sides to remove the Front Panel. 2) Loosen 2 screws on the board and 4 screws at the rear of the set to remove the Zoran Board. Figure 4-4 Figure 4-5 B C 3) Loosen 2 screws to remove the PSU Board. Figure 4-6 D EN 123139 785 317704.Dismantl

28、ing Instructions & Service Positions 4.3 Service Positions Service Position - Front PanelService Position - Zoran Board Insulation Sheet Front Panel Board Insulation Sheet Zoran Board EN 133139 785 317705.Service Test Program 5. Service Test Program TESTActivated withACTION EEPROM FORMAT TEST to Exi

29、t Load default data. Display shows “NEW”. Caution! All presets from the customer will be lost! LEAVE SERVICE TEST PROGRAM Disconnect mains cord To start service test program hold button depressed while set is in standby and press the STANDBY button* Display shows the ROM version “SVxx-yy” * Mains po

30、wer to set must be on Hold button depressed till the Display shown “SVxx-yy” S refers to Service Mode V refers to Version xx refers to Software version number of the back uProcessor (counting up from 01 to 99) yy refers to the front uProcessor version number (00 will be displayed if there is no fron

31、t uProcessor use) Button pressed? N Y Display shows Figure 1 and switch Multichannel & Progressive Scan LEDs on N Y Display shows Figure 2 and switch Multichannel & Progressive Scan LEDs off MAIN MENU DISPLAY TEST N Y Button pressed? Button pressed? Figure 1 Figure 2 Various other Tests EN 143139 78

32、5 317705.Service Test Program 5.1.1 Reprogramming of DVD version Matrix After repair, the customer setting and region code may be lost. Reprogramming will put the set back in the state in which it has left the factory, ie. with the default setting and the allowed region code. Model Region Region Cod

33、e TV Type DVP 5900/12 Europe 2 PAL DVP 5900/98AP 3 PAL DVP 5900/93China 6 PAL DVP 5900/37Nafta 1 NTSC DVP 5900/05UK/Ireland2 PAL To reprogram do as follows: 1) Power up the set. 2) Open tray by press “OPEN/CLOSE” button on the set or press and hold “STOP” button on the RC. 3) Press the following but

34、tons on the Remote Control: .for DVP 5900/12, DVP 5900/05 .for DVP 5900/51 .for DVP 5900/98 .for DVP 5900/93 .for DVP 5900/37 4) The display shows YYYY-ZZ and the tray will close. YYYY = model number (eg. 0720, 3900, etc.) ZZ = stroke version (eg. 00, 02, 05, etc.) 5.1.2 Procedure for check Software

35、 version 1) Power up the set. 2) Open tray by press “OPEN/CLOSE” button on the set or press and hold “STOP” button on the RC. 3) Press “DISPLAY” button on the Remote control. 4) The TV screen will shows: SD6.1 Vxx YYYY-ZZ P QQ SERVO: GGGGGGGG REG:D xx = version number YYYY = model number (eg. 0720,

36、3900, etc.) ZZ = stroke version (eg. 00, 02, 05, etc.) P / D = region code QQ = version number of front uProcessor GGGGGGGG = version for servo code 5.1.3 Procedure to upgrade software 1) Power up the set. 2) Open tray by press “OPEN/CLOSE” button on the set or press and hold “STOP” button on the RC

37、. 3) Place upgrade CD-ROM onto tray and close. 4) The set will response and display the following: - LOAD After the disc is read, the tray will open for you to remove the disc - ERASE - WRITE - ERROR if upgrade is unsuccessful - UPG END - PHILIPS if upgrade is successful - DISC-CLOSE-LOAD Tray will

38、close indicating that the upgrade process is completed 5) The whole process should not take more than 5 minutes. Caution: Do not unplug the set until upgrade is completed. 5.1.4 Trade Mode Trade mode is a feature that will block all set keys when enabled. It is for dealers to prevent customers from

39、removing disc, changing source etc using the set keys. Rotary and Remote Control (RC) keys are still allowed in Trade mode. To activate Trade Mode: 1) Power up the set. 2) Open tray by press “OPEN/CLOSE” button on the set or press and hold “STOP” button on the RC. 3) Then press buttons on the RC. 4)

40、 The display shows TRA ON and the tray will close. Trade Mode is now enabled. To deactivate Trade Mode: 1) Power up the set. 2) Open tray by press and hold “STOP” button on the RC. 3) Then press buttons on the RC. 4) The display shows TRA OFF and the tray will close. Trade Mode is now disabled. EN 1

41、53139 785 317706Block Diagram, Wiring Diagram 0095PVD margaiD kcolB 87763RZ REDOCED GEPM OVRESIC 70763RZ EVIRD ROTOMR S8885MA F R O M O P U t i bM61 HSALF t i bM61 MARDS ro t cennoC o i duA 1027 0157 1157 10372027 o i duA h c - 2 1051 )no i s i vorp(1011 3011 TE5834KA IMDH ro t cennoC 1061 IMDH 1276

42、3RZ WS OEDIV BCP t r acS t r acS t u O o e d i VSBVC / r P-bP-Y 2011 7404 0167 0117 moc dna nac s - Ps t nenop REDAOL ELUDOM REWOP YLPPUS r ev i rD DFV C2I y a l p s i D t necseroulF muucaV m-yeKax i r t rev i eceR RI f Vma l ie t n r e f fuB : y l ppuS yb t sV5+ V21+ V42- DEL ybdnatS t ce t eD DRAO

43、B ONOM DRAOB TNORF S-oed iV 6. Block Diagram EN 163139 785 317706.Block Diagram, Wiring Diagram 13 A 8910 13 12345 G H I E F 9101112 G H 56 7 6 J 1 F E D C B 1112 A B C D 6 7 8 9 8 J 234 7 I 1 10 11 2 3 4 5 2 3 4 5 6 1503 B11B-PH-K 1 2 B6B-PH-K 1XXX 1 7 8 9 WH02D-1 1104 1 10 11 12 2 3 4 5 66 7 8 9 B

44、12B-EH-A CN2021106 B12B-EH-A 1 10 11 12 2 3 4 5 1 2 3 4 5 3 4 5 1011 1-D50HW 9 1-D50HW 0011 1 2 1 2 3 4 5 6 7 8 4 5 6 7 8 9 7011 1-D90HW1-D90HW 2011 1 2 3 1 2 3 4 5 WH02D-1 1XXX 1 2 B5B-PH-K 1XXX XXX1 A-KRTB-NMF42 1501 24FMN-BTRK-A 14 2 3 4 5 6 7 8 9 1 10 11 12 13 14FE-BT-VK-N 1106 2001 14FE-BT-VK-N

45、 SET WIRING DVP5900 31392493315_2005-08-26 Wiring Diagram EN 173139 785 317707 5 5 4 4 3 3 2 2 1 1 DD CC BB AA VID0 VID1 VID2 VID3 VID4 VID5 VID6 VID7 VCLKX2 TMDS_D2+ TMDS_D2- TMDS_D1+ TMDS_D1- TMDS_D0- TMDS_CLK- RESET- HD_VDDDAC HD_AVDDT33 HD_AVDDT18 HD_VDDPLL HD_CLK HD_DAT SPDIF CLOSE OPEN FS3 /AU

46、DIO_RESET TMDS_D0+ TMDS_CLK+ VSYNC HSYNC HOTPLUGHOTPLUG_F HOTPLUG DDCDAT TMDS_D0+ TMDS_D2- TMDS_D2+ TMDS_CLK- TMDS_CLK+ TMDS_D0- TMDS_D1- HDMI5V DDCCLK A+12V TMDS_D1+ GND TMDS_CLK+ TMDS_D2- TMDS_D0+ TMDS_CLK- TMDS_D1- TMDS_D1+ TMDS_D2+ TMDS_D0- HDVCC33 HDVCC18 HDVCC33 HDVCC33 HDVCC18 HDVCC18HDVCC33

47、TDMSGND HD_AVDDT33 HD_AVDDT33 DSPVCC33 TDMSGND HDMI5V A+12V HDMI5V HDMI5V A+12V TDMSGND DSPVCC33 HDVCC33 DSPVCC18 VID0 VID1 VID2 VID3 VID4 VID5 VID6 VID7 VCLKX2 RESET- HD_CLK OPEN CLOSE FS3 OSCOUT VSYNC HSYNC GCLKA HD_DAT HDVCC18HDVCC33 DDCCLK A+12V DDCDAT DSPVCC33 DSPVCC33 HDVCC33 DSPVCC18 4385CS S

48、PDIF FS1 FS2 /AUDIO_RESET CCLK CDTI ZR36721 C272 & C179 should be nearby Pin48 & Pin54 of I77 Power for I77_AVDDT33 Please Note: TDMSGND should be connected to GND at a single point. HDMI_TYPE_A Adjust pin current 3619 55 or 60uA 2.87K/1% 90uA 2.8K/1% HDMI 5V.(4.955.05V) TMDS: Transition Minimized Differential Signaling DDC signal Capacitance: 50pF 3615 4.7K 3626 1K + 2622 47uF/16V 7611 B1117-ADJ ADJ/GND 1 OUT2 2 IN 3 OUT1 4 7606 2N7002 1 32 2609 0.1uF 3609 0R 3625 2.7K 3605 75R/1% 2614 0.1uF +2608 100uF/16V 5606 FB220R 7603PSS8550 1 23 3612 4.7K 2615 0.1uF 361