Philips-HTD-5540-Service-Manual(1) 电路图 维修手册.pdf

《Philips-HTD-5540-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-HTD-5540-Service-Manual(1) 电路图 维修手册.pdf（56页珍藏版）》请在收音机爱好者资料库上搜索。

1、TABLE OF CONTENTS Page Service Manual . Mechanical and Dismantling Instructions.3-1 . Software Upgrades .4-1 . Trouble Shooting Chart.5-1 . Wiring Diagram.6-1 . Electrical Diagrams and Print-layouts.7-1 . Set Mechanical Exploded view 247 x 1090 x 242 mm (rear) ? HTD5570: 247 x 1090 x 242 mm (front/r

2、ear) ?Weight (front): ? HTD5510: 0.53 kg/each ? HTD5540: 0.53 kg/each ? HTD5570: 2.66 kg/each ?Weight (rear): ? HTD5510: 0.56 kg/each ? HTD5540/HTD5570: 2.72 kg/each ?Cable length (front): 3.25 m ?Cable length (rear): 10.25 m Remote control batteries ?1 x AAA-R03-1.5 V Laser ?Type: Semiconductor las

3、er GaAIAs (CD) ?Wave length: 650-662 nm (DVD), 785-795 nm (CD) ?Output power: 6 mW (DVD), 7 mW (VCD/CD) ?Beam divergence: 60 degrees. 1-4 Safety instruction 1. General safety Safety regulations require that during a repair: . Connect the unit to the mains via an isolation transformer. . Replace safe

4、ty components indicated by the symbol , only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard. Safety regulations require that after a repair, you must return the unit in its original condit

5、ion. Pay, in particular, attention to the following points: . Route the wires/cables correctly, and fix them with the mounted cable clamps. . Check the insulation of the mains lead for external damage. . Check the electrical DC resistance between the mains plug and the secondary side: 1) Unplug the

6、mains cord, and connect a wire between the two pins of the mains plug. 2) Set the mains switch the “on” position (keep the mains cord unplug). 3) Measure the resistance value between the mains plug and the front panel, controls, and chassis bottom. 4) Repair or correct unit when the resistance measu

7、rement is less than 1M?. 5) Verify this, before you return the unit to the customer/user (ref. UL-standard no. 1492). 6) Switch the unit “off”, and remove the wire between the two pins of the mains plug. 2.Laser safety This unit employs a laser. Only qualified service personnel may remove the cover,

8、 or attempt to service this device (due to possible eye injury). Laser device unit Type : Semiconductor laser GaAlAs Wavelength : 650nm (DVD) : 780nm (VCD/CD) Output power : 7mW (DVD) : 10mW (DVD /CD) Beam divergence: 60 degree Note: Use of controls or adjustments or performance of procedure other t

9、han those specified herein, may result in hazardous radiation exposure. Avoid direct exposure to beam. Safety instruction, Warning press up or down to slow forward or slow backward (for DVD video only). ? In radio mode, press left or right to search a radio station; press up or ? d OK ? e BACK Retur

10、n to a previous menu screen. f +/- Increase or decrease volume. g (Mute) Mute or restore volume. h / (Previous/Next) ? Skip to the previous or next track, ? ? In radio mode, select a preset radio station. i Numeric buttons Select an item to play. j SOUND Select a sound mode. k SURR Select surround s

11、ound or stereo sound. l (Play/Pause) Start, pause or resume play. m (Stop) Stop play. n OPTIONS Access more play options while playing a disc or a USB storage device. o (Open/Close) Open or close the disc compartment. p (Home) Access or exit the home menu. q AUDIO SYNC ? Select an audio language or

12、channel. ? Press and hold to access audio delay setting, then press Navigation buttons (left/right) to delay the audio to match the video. Connectors This section includes an overview of the connectors available on your home theater. Front a (USB) Audio, video or picture input from a USB storage dev

13、ice. b AUDIO IN Audio input from an MP3 player (3.5mm jack). Back connectors a AC MAINS Fixed AC power cable. 2-2 b SPEAKERS Connect to the supplied speakers and subwoofer. c VIDEO OUT Connect to the composite video input on the TV. d AUDIO IN-AUX Connect to an analog audio output on the TV or an an

14、alog device. e DIGITAL IN-OPTICAL Connect to an optical audio output on the TV or a digital device. f HDMI OUT (ARC) Connect to the HDMI input on the TV. g FM ANTENNA Connect the supplied antenna for radio reception. 2-3 Connect and set up This section helps you connect your home theater to a TV and

15、 other devices, and then set it up. For information about the basic connections of your home theater and accessories, see the quick start guide. Note ? at the back or bottom of the product. ?Before you make or change any connections, make sure that all devices are disconnected from the power outlet.

16、 Connect speakers The speaker cables are color-coded for easy connection. To connect a speaker to your home theater, match the color on the speaker cable to the color on the connector. Speaker position plays a critical role in setting up a surround sound effect. For best effect, position all the spe

17、akers towards the seating position and place them close to your ear level (seated). * The actual speaker shapes may vary from the illustration above. Note ?Surround sound depends on factors such as room shape and size, type of wall and ceiling, windows and ? ? for you. Follow these general guideline

18、s for speakers placement. 1Seating position: This is the center of your listening area. 2FRONT CENTER (front center) speaker: Place the center speaker directly in front of the seating position, either above or below your TV. 3FRONT LEFT (front left) and FRONT RIGHT (front right) speakers: Place the

19、left and right speakers in the front, and at equal distance from the center speaker. Make sure that the left, right, and the center speakers are at equal distance from your seating position. 4REAR LEFT (rear left) and REAR RIGHT (rear right) speakers: Place the rear surround speakers to the left and

20、 right side of your seating position, either in line with it or slightly behind it. REAR RIGHT FRONT LEFT FRONT CENTER FRONT RIGHT REAR LEFT SUB WOOFER 2-4 5SUBWOOFER (subwoofer): Place the subwoofer at least one meter to the left or right of the TV. Leave about 10-centimeter clearance from the wall

21、. Connect to TV Connect your home theater to a TV to watch videos. You can listen to the TV audio through your home theater speakers. Use the best quality connection available on your home theater and TV. Option 1: Connect to TV through HDMI (ARC) Best quality video Your home theater supports HDMI v

22、ersion with Audio Return Channel (ARC). If your TV is HDMI ARC compliant, you can hear the TV audio through your home theater by using a single HDMI cable. 1Using a High Speed HDMI cable, connect the HDMI OUT (ARC) connector on your home theater to the HDMI ARC connector on the TV. ? The HDMI ARC co

23、nnector on the TV might be labeled differently. For details, see the TV user manual. 2On your TV, turn on HDMI-CEC operations. For details, see the TV user manual. ? HDMI-CEC is a feature that enables CEC compliant devices that are connected through HDMI to be controlled by a single remote control,

24、TV such as volume control for both the TV and the home theater. (see Set up EasyLink (HDMI-CEC control) on page 10) 3If you cannot hear the TV audio through your home theater, set up the audio manually. Option 2: Connect to TV through standard HDMI Best quality video If your TV is not HDMI ARC compl

25、iant, connect your home theater to the TV through a standard HDMI connection. 1Using a High Speed HDMI cable, connect the HDMI OUT (ARC) connector on your home theater to the HDMI connector on the TV. 2Connect an audio cable to hear the TV audio through your home theater (see Connect audio from TV a

26、nd other devices on page 9). 3On your TV, turn on HDMI-CEC operations. For details, see the TV user manual. ? HDMI-CEC is a feature that enables CEC compliant devices that are connected through HDMI to be controlled by a single remote control, such as volume control for both the TV and the home thea

27、ter. (see Set up EasyLink (HDMI-CEC control) on page 10) TV 2-5 4If you cannot hear the TV audio through your home theater, set up the audio manually. Note ?If your TV has a DVI connector, you can use an HDMI/ DVI adapter to connect to TV. However, some of the features may not be available. Option 3

28、: Connect to the TV through composite video Basic quality video If your TV does not have HDMI connectors, use a composite video connection. A composite ? video. 1Using a composite video cable, connect the VIDEO OUT connector on your home theater to the VIDEO IN connector on the TV. ? The composite v

29、ideo connector might be labeled AV IN,COMPOSITE, or BASEBAND. 2Connect an audio cable to hear the TV audio through your home theater (see Connect audio from TV and other devices on page 9). 3When you watch TV programs, press SOURCE on your home theater repeatedly to select the correct audio input. 4

30、When you watch videos, switch your TV to the correct video input. For details, see the TV user manual. TV Connect audio from TV and other devices Play audio from TV or other devices through your home theater speakers. Use the best quality connection available on your TV, home theater, and other devi

31、ces. Note ?When your home theater and TV are connected through HDMI ARC, an audio connection is not required (see Option 1: Connect to TV through HDMI (ARC) on page 8). Option 1: Connect audio through a digital optical cable Best quality audio 1Using an optical cable, connect the OPTICAL connector o

32、n your home theater to the OPTICAL OUT connector on the TV or other device. ? The digital optical connector might be labeled SPDIF or SPDIF OUT. TV 2-6 Option 2: Connect audio through analog audio cables Basic quality audio 1Using an analog cable, connect the AUX connectors on your home theater to t

33、he AUDIO OUT connectors on the TV or other device. Set up speakers Set up the speakers manually to experience customized surround sound. Before you start Make the necessary connections described in the quick start guide, and then switch the TV to the correct source for your home theater. 1Press (Hom

34、e). 2Select Setup, and then press OK. 3Select Audio Speaker Setup. 4Press the Navigation buttons and OK to select and change: ? Speakers Volume: Set the volume level of each speaker. ? Speakers Delay: Set the delay time for speakers which are placed closer to the seating position in order to obtain

35、equal audio transmission from all the speakers. VCR AUDIO IN- AUX Set up EasyLink (HDMI-CEC control) This home theater supports Philips EasyLink, which uses the HDMI-CEC (Consumer Electronics Control) protocol. EasyLink- compliant devices that are connected through HDMI can be controlled by a single

36、 remote control. Note ?Depending on the manufacturer, HDMI-CEC is known by many names. For information on your device, see the user manual of the device. ?Philips does not guarantee 100% interoperability with all HDMI-CEC devices. Before you start ?Connect your home theater to the HDMI- CEC complian

37、t device through HDMI connection. ?Make the necessary connections described in the quick start guide, and then switch the TV to the correct source for your home theater. Enable EasyLink 1Press (Home). 2Select Setup, and then press OK. 3Select Video, and then press OK. 4Select HDMI Setup EasyLink Set

38、up EasyLink On. 5On your TV and other connected devices, turn on HDMI-CEC control. For details, see the user manual of the TV or other devices. ? On your TV, set the audio output to ? For details, see the TV user manual. 2-7 EasyLink controls With EasyLink, you can control your home theater, TV, and

39、 other connected HDMI-CEC compliant devices with a single remote control. ?One Touch Play (One-touch play): If one- touch play is enabled, press (Standby- On) on the remote control of your home theater to wake up the TV from standby. ?One Touch Standby (One-touch standby): If one-touch standby is en

40、abled, your home theater can switch to standby with the remote control of the TV or other HDMI-CEC devices. ?Sys Audio Control (System audio control): If system audio control is enabled, the audio of the connected device is output through your home theater speakers automatically when you play the de

41、vice. ?Audio Mapping (Audio input mapping):If system audio control does not work, map the connected device to the correct audio input connector on your home theater. Note ?To change the EasyLink control settings, press (Home), select Setup Video HDMI Setup EasyLink Setup EasyLink. Set up the audio I

42、f you cannot hear the audio output of a connected device through your home theater speakers, do the following: ?Check that you have enabled EasyLink on all the devices (see Set up EasyLink (HDMI-CEC control) on page 10). 1Press (Home). 2Select Setup, and then press OK. 3Select Video, and then press

43、OK. 4Select HDMI Setup EasyLink Setup Sys Audio Control On. ? To play the audio from the TV speakers, select Off, and skip the following steps. 5Select HDMI Setup EasyLink Setup Audio Mapping. 6Follow the onscreen instructions to map the connected device to the audio inputs on your home theater. ? I

44、f you connect your home theater to the TV through an HDMI ARC connection, make sure that the TV audio is mapped to the ARC input on your home theater. 2-8 Mechanical and Dismantling Instructions Dismantling Instruction The following guidelines show how to dismantle the player. 3-1 Detailed informati

45、on please refer to the model set. Step1: Open the top cover. Remove 2 screws on both sides and 4 screws on back panel,then open the cover. (Figure 1) Figure 1 Figure 2 Step2:Dismantle the loader.Open the tray,dismantle the CD door,remove 2 screws beside the loader. disconnect connectors(XP100,XP135,

46、XP136),then pull up the loader.(Figure 2) XP100 XP135 XP136 Mechanical and Dismantling Instructions Dismantling Instruction The following guidelines show how to dismantle the player. 3-2 Detailed information please refer to the model set. Step3:Dismantle the main board.Disconnect connectors(XP221,XP

47、82,XS751),remove 2 screws on the board and 6 screws on back panel.(Figure 3) Figure 3 Step4:Dismantle the power board.Remove 4 screws on the board.(Figure 3) Step5:Dismantle the front panel and the front control board.Loosen the 2 buckles on both sides and 2 buckles under bottom cover,then remove 5 screws on the front control board(Figure 4) Figure 4 XP221 XP82 XS751 Software Upgrade 1. There are 2 ways to software upgrade: First: Upgrade from USB: Copy the upgrade file HTD5510_X X.BIN to USB then press the USB key on RC or SOURCE key on front panel. When upgrade file