Philips-HDD-1620-Service-Manual(1) 电路图 维修手册.pdf

《Philips-HDD-1620-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-HDD-1620-Service-Manual(1) 电路图 维修手册.pdf（27页珍藏版）》请在收音机爱好者资料库上搜索。

1、Micro Audio Jukebox HDD1420/1620/1630/1635/1830/1835 All version 3141 785 30705 Version 1.5 TABLE OF CONTENTS Chapter Technical Specification and Service hints.1 Safety Instructions2 Instructions for Use. 3 Mechanical Instructions. 4 Exploded view and Service parts list. 5 Troubleshooting flow. 6 Ov

2、erall Block diagram. 7 Overall Electrical diagram. 8 IRIS CODE9 Revision list 10 Service Manual Copyright 2005 Philips Consumer Electronics B.V. Eindhoven, The Netherlands All rights reserved. No part of this publication may by reproduced, stored in a retrieval system or transmitted, in any form or

3、by any means, electronics, mechanical, photocopying, or otherwise without the prior permission of Philips RadioFans.CN 收音机爱 好者资料库 1.0 TECHNICAL SPECIFICATION and SERVICE HINTS General Dimensions (WxHxD) : 53.7 X 86.0 X 16.3 mm (2.11 x 3.39 x 0.64 inch) Weight : 87 g Output power : 2 x 5 mW (16 Ohm)

4、Frequency response : 20 16 000 Hs Equalizer : 5-bands Hard disk : Capacity : 4GB 6GB Display : 128 x 128 pixels, 65K color Backlight : White Battery : 630 mAh Li-Ion rechargeable battery Battery life time: 16hrs File transfer rate using USB2.0 : 4Mbyte Battery charging current 450mA Maximum charging

5、 time : 4hr Battery cutoff voltage: 3.7V Connections: Headphone Line Out Jack Power Connector Battery level detection Detection Level Typ. 4-step to 3-step voltage 3.6 3.7V 3-step to 2-step voltage 3.53 3.6V 2-step to 1-step voltage 3.48 3.53V Force Power Off voltage 3.5V Current consumption DC-IN S

6、UPPLY (4.5V) Battery Charging Current 450mA BATT. SUPPLY (3.7V) Power Off 300uA Idle 30mA Playback without HDD reading 30mA Playback with HDD reading 345mA File transfer using USB2.0 350mA Headphone out (headphone output load 2x16 ohm) Maximum output power : 10 mW Frequency response : 45Hz 16kHz (16

7、 load) 20Hz 16kHz (15k load) SNR (A-wght) : 85dB THD (1kHz) : 0.1% Left-Right Channel Separation : 45dB typ. (1k Hz) 40dB typ. (20Hz 16kHz) Left-Right Channel Balance : 1.0dB (1k Hz) Programs- Philips Device Manager-Philips Device Manager on your PC. 5. Click Update in the dialogue box the Philips D

8、evice Manager will detect the connection of your GoGear and the application will automatically check on the server to see if an update is available and prompt user to download the updated firmware. Click YES to start the downloading. RadioFans.CN 收音机爱 好者资料库 1.0 TECHNICAL SPECIFICATION and SERVICE HI

9、NTS 6. A status bar will show the downloading progress of the firmware. Once the downloading is complete the application will prompt you to install the update onto your GoGear. Click YES to confirm 7. The application will show the status of updating and at the end you need to click OK to complete th

10、e update. (Please do not disconnect the jukebox during the upgrading process as this interruption may damage the firmware!) 8. Follow all screen instructions to complete the firmware upgrade. 9. The Device Manager will close automatically once the success message is displayed. Close all opened appli

11、cation and then unplug your GoGear. 10. Once the GoGear micro jukebox is disconnected from the computer, the display will show “Firmware Upgrading” for a couple of seconds and then start up as usual. If the message does not disappear after 2 minutes, do a soft reset by pressing and holding the Power

12、 on/off key and the volume + key for a couple of seconds. Repair the firmware with Device Manager 1. If you have not already installed the Device Manager download the latest version of the Device Manager from You may need to enter your language preference and the model number e.g.HDD1630, to access

13、the Device/Firmware Manager upgrade file. 2. Download the zip file into a temp folder in your computer. Unzip the file and then double click the Setup.exe file to start the installation of the Device Manager. 3. Once the installation is complete, connect the GoGear to the power supply with the AC/DC

14、 adapter. 4. Make sure all other applications such as Philips Device plug-in, Windows Media Player or Windows Explorer that accessing the device are closed or else Device Manager will not recognize the device. Launch the Philips Device Manager at Start-Programs- Philips Device Manager-Philips Device

15、 Manager on your PC. RadioFans.CN 收音机爱 好者资料库 1.0 TECHNICAL SPECIFICATION and SERVICE HINTS 5. Click YES to start the downloading. A status bar will show the downloading progress of the firmware. Once the downloading is complete the application will prompt you to install the update onto your GoGear.

16、6. Once the repair is complete a dialogue box will pop up; click OK and unplug the GoGear from the computer. IMPORTANT: All music fr Reparaturen sind Original-Ersatzteile zu verwenden. I Le norme di sicurezza esigono che lapparecchio venga rimesso nelle condizioni originali e che siano utilizzati i

17、pezzi di ricambio identici a quelli specificati. After servicing and before returning set to customer perform a leakage current measurement test from all exposed metal parts to earth ground to assure no shock hazard exist. The leakage current must not exceed 0.5mA. CLASS 1 LASER PRODUCT 3122 110 034

18、20 GBWarning ! Invisible laser radiation when open. Avoid direct exposure to beam. SVarning ! Osynlig laserstrlning nr apparaten r ppnad och sprren r urkopplad. Betrakta ej strlen. SFVaroitus ! Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina nkymttmlle laseristeilylle. l katso stee

19、seen! DKAdvarse ! Usynlig laserstrling ved bning nr sikkerhedsafbrydere er ude af funktion. Undg udsaettelse for strling. 2.0 SAFETY INSTRUCTIONS Battery Handling Guideline Since the battery is packed in soft package, to ensure its better performance, its very important to carefully handle the batte

20、ry 2.1 Soft Aluminium foil The soft aluminum packing foil is very easily damaged by sharp edge parts such as Ni-tabs, pins and needles. Dont strike battery with any sharp edge parts Trim your nail or wear glove before taking battery Clean worktable to make sure no any sharp particle 2.2 Sealed edge

21、Sealing edge is very flimsy Dont bend or fold sealing edge 2.3 Folding edge The folding edge is form in battery process and passed all hermetic test. Dont open or deform folding edge 2.4 Tabs The battery tabs are not so stubborn especially for aluminum tab. Dont bend tab 2.5 Mechanical shock Dont Fa

22、ll, hit, bend battery body 2.6 Short Short terminals of battery is strictly prohibited, it may damage battery. 3.0 INSTRUCTION FOR USE Power Connector 4.0 MECHANICAL INTRUCTIONS Set Disassembly 1. Add a tape over the knobs on two side before opening the set to prevent the knobs will fall out the set

23、 after open. 2. Remove the cosmetic screw on the back cover by Allen Key. 3. Finger inset the gap of the top cover assy and the housing, and then carefully lift up the top cover. 4. Generally remove the housing. 4.0 MECHANICAL INTRUCTIONS 5. Remove the 4 screws on four corners. See pointed arrows. 6

24、. Carefully pull out the mainboard assy, which include the HDD drive, LCD, battery and PCBA board. 7. Disconnect the flex cable from the front touch screen module carefully, then free the top cover assy. 8. Lift up the double side tape of the side buttons. 4.0 MECHANICAL INTRUCTIONS 9. Turn to the b

25、ottom side. 10. Open up the metal shielding and disconnect the cable connected to the battery. Carefully disassemble the mini mic as circled in the picture from the plastic audio jack holder. 11. Remove the battery part form PCBA. 12. Lift up the hard disk and disconnect the flex cable underneath fr

26、om the PCBA. 4.0 MECHANICAL INTRUCTIONS 13. After remove both battery and hard disk. 5.0 EXPLODED VIEW AND SERVICE PARTS LIST 101 114 100 105 103 102 106 107 108 109 110 111 117116 118 115 104 112113 MECHANICAL PARTS 100 994000003554 COSMETIC SREW PHOENIX 101 994000003555 BACK CABINET PHOENIX 102 99

27、4000003559 AUDIO JACK HOLDER ASSY 103 994000003556 SHIELDING PHOENIX 104 994000003572 CRADLE HOLDER PHOENIX 105 994000003558 SCREW 1.7X5 PHOENIX 106 994000003557 BATTERY PACK PHOENIX 107 282206200084 282206200079 HDD 4GB (HDD1420/00) HDD 6GB (HDD1620/00/05, HDD1630/17 47U,6.3V, +/-20%,3216,1.6H, (A

28、case),F930J476MAA,SMT MSCDRI-2D18-100MG (H=1.8mm)美磊 Use low height Cap. Place it to 1.5mm limit region 12 R37 100K/NA 0402 5% R37 100K/NA 0402 5% 12 R594 100K 0402R594 100K 0402 1 32 D S Q3 PMF780SN SOT_SC70N_1 D S Q3 PMF780SN SOT_SC70N_1 12 C81 10U 16V 1206 C81 10U 16V 1206 12 L10 3.3UH L10 3.3UH V

29、IN 1 VSS 2 CE/MODE 3 VOUT 4 LX 5 U6 XC9216 SOT25 U6 XC9216 SOT25 1 2 3 D506 1PS89SB15 SOT523N D506 1PS89SB15 SOT523N 12 JO501 SPARKGAP_6 JO501 SPARKGAP_6 1 2 3 D3 1PS89SB15 SOT523N D3 1PS89SB15 SOT523N G DS D SQ4 AO3415 SOT23_FET D SQ4 AO3415 SOT23_FET 12 C32 0.1U 0402 16V C32 0.1U 0402 16V 12 C21 0

30、.1U 0402 10V C21 0.1U 0402 10V 12 R529 100K 0402 5% R529 100K 0402 5% 12 + C28 47U 10V 3528 + C28 47U 10V 3528 12 JO4 SHORT- SMT2 JO4 SHORT- SMT2 12 JO7 SHORT- SMT3 JO7 SHORT- SMT3 12 C31 1U 0402 6.3V +/-10% C31 1U 0402 6.3V +/-10% 12 R34 10K 0402 5% R34 10K 0402 5% 12 JO6 SHORT- SMT3 JO6 SHORT- SMT

31、3 12 R531 0/NA 0402 5% R531 0/NA 0402 5% 1 32 D S Q2 PMF780SN SOT_SC70N_1 D S Q2 PMF780SN SOT_SC70N_1 12 JO502 SPARKGAP_6 JO502 SPARKGAP_6 12 F2 2A/32V F2 2A/32V VIN 1 VSS 2 CE/MODE 3 VOUT 4 LX 5 U8 XC9216 SOT25 U8 XC9216 SOT25 12 R54 100K 0402 1% R54 100K 0402 1% 12 JO3 SHORT- SMT3 JO3 SHORT- SMT3

32、12 JO2 SHORT- SMT3 JO2 SHORT- SMT3 12 R83 100K/NA 0402 R83 100K/NA 0402 12 C539 180P 0402 50V +/-10% C539 180P 0402 50V +/-10% STAT1 2 STAT2 3 AC 4 ISET2 7 PSEL/ISET3 8 CE 9 VSS 11 ISET1 10 TS 12 DPPM 13 TMR 14 ACPG 18 USBPG 19 USB 20 LDO 1 GND 21 OUT_0 15 OUT_1 16 OUT_2 17 BAT_0 5 BAT_1 6 U2 BQ2403

33、2 QFN_RHL20 U2 BQ24032 QFN_RHL20 12 C76 0.1U 0402 10V C76 0.1U 0402 10V 12 R64 0 0402 R64 0 0402 12 JO503 SHORT- SMT3 JO503 SHORT- SMT3 12 R35 2.32K 0402 1% R35 2.32K 0402 1% 12 C65 10U 6.3V 0805 10% C65 10U 6.3V 0805 10% 12 R75 33K/NA 0402 5% R75 33K/NA 0402 5% 12 C56 0.1U 0402 10V C56 0.1U 0402 10

34、V 12 + C95 47U 10V 3528 + C95 47U 10V 3528 12 R522 100K0402 1% R522 100K0402 1% 12 R44 10K 0402 5% R44 10K 0402 5% 12 L3 6.8UH SPC- 04702 30%L3 6.8UH SPC- 04702 30% 12 R57 100K/NA 0402 R57 100K/NA 0402 12 R31 100K 0402 5% R31 100K 0402 5% 1 2 GND1 GND2 3 J502 MA/3PX1/ST ACES 87212- 0300 J502 MA/3PX1

35、/ST ACES 87212- 0300 12 R33 100 0402 R33 100 0402 12 C42 10U 16V 1206 C42 10U 16V 1206 12 C24 0.1U 0402 10V C24 0.1U 0402 10V 12 C536 27P 0402 50V 5% C536 27P 0402 50V 5% 12 JO8 SHORT- SMT3 JO8 SHORT- SMT3 12 R74 0 0402 R74 0 0402 12 L8 10UH MSCDRI- 2D18C 20% L8 10UH MSCDRI- 2D18C 20% 12 R29 2M 0402

36、 1% R29 2M 0402 1% 12 R523 560K 0402 1% R523 560K 0402 1% 12 F1 2A/32V F1 2A/32V 12 C78 10U 6.3V 0805 C78 10U 6.3V 0805 12 C79 10U 6.3V 0805 C79 10U 6.3V 0805 12 R573 100K 0402 R573 100K 0402 12 R32 1M 0402 1% R32 1M 0402 1% 12 R28 10K 0402 1% R28 10K 0402 1% VI 1 FB 4 GND 2 EN 3 SW 5 U7 TPS62200 SO

37、T25 U7 TPS62200 SOT25 12 R70 47K 0402 1% R70 47K 0402 1% 12 R39 0/NA 0402_DFS 5% R39 0/NA 0402_DFS 5% 1 TP6TP6 12 R598 100K 0402 5% R598 100K 0402 5% 12 R599 1M 0402 1% R599 1M 0402 1% 12 R62 33K/NA 0402 5% R62 33K/NA 0402 5% 12 R27 0/NA 0402 R27 0/NA 0402 1 32 D S Q504 PMF780SN SOT_SC70N_1 D S Q504

38、 PMF780SN SOT_SC70N_1 12 C22 1U 0402 6.3V +80-20% C22 1U 0402 6.3V +80-20% 12 R26 20K 0402 1% R26 20K 0402 1% EN 1 VIN_0 2 VIN_1 3 GND 4 FB 5 MODE 6 SW_0 7 SW_1 8 PGND_0 9 PGND_1 10 GND1 11 U3 TPS62040 MLFP10A_05MM_GND U3 TPS62040 MLFP10A_05MM_GND 12 C34 0.1U 0402 16V +80-20% C34 0.1U 0402 16V +80-2

39、0% 12 C25 10U 0805 10V +80-20% C25 10U 0805 10V +80-20% 12 R530 0/NA 0402R530 0/NA 0402 12 L9 3.3UH L9 3.3UH 12 R48 100K 0402 R48 100K 0402 12 R361K 0402 1%R361K 0402 1% 12 R69 33K 0402 1% R69 33K 0402 1% 12 R45 40.2K 0402 1% R45 40.2K 0402 1% 12 R30 100K 0402 5% R30 100K 0402 5% 12 JO5 SHORT- SMT3

40、JO5 SHORT- SMT3 AK D5 PMEG3005AEA SOD323B D5 PMEG3005AEA SOD323B 12 R41 100K 0402 R41 100K 0402 12 C30 0.1U 0402 10V C30 0.1U 0402 10V 12 R73 100K 0402 1% R73 100K 0402 1% 12 C73 10U 16V 1206 C73 10U 16V 1206 12 C74 0.1U 0402 10V C74 0.1U 0402 10V 12 R40 36K 0402 1% R40 36K 0402 1% 12 C23 10U 16V 12

41、06 C23 10U 16V 1206 5 5 4 4 3 3 2 2 1 1 DD CC BB AA I2S_SCLK_IN BM3_KSI12 MIC_BIAS I2C.DAT BM3_KSI1 BM3_KSI6 DCVDD I2C.CLK DBVDD BM3_KSI0 BM3_KSI10 BM3_KSI8 FM_AUDIO_AC_L FM_AUDIO_AC_R BM3_KSI5 BM3_KSI11 HP_OUT_L I2S_DOUT MIC_BIAS I2S_LRC AVDD HPVDD BM3_KSI2 BM3_KSI3 MIC_IN BM3_KSI4 I2S_SCLK BM3_KSI

42、7 I2S_SDIN PWR_ON_OFF# BZZ_GND BM3_KSI12 BM3_KSI1 BM3_KSI2 PWR_ON_OFF# BM3_KSI8 BM3_KSI3 BM3_KSI0 HP_OUT_R LED_PWR AUDIO_LDO_IN BM3_KSI5 BM3_KSI4 BM3_KSI3 BM3_KSI1 BM3_KSI2 BM3_KSI0 BM3_KSI5 BM3_KSI4 BM3_KSI10 BZZ_PWM BM3_KSI9 HP_OUT_R_1 REMOTE_JACK_1 HP_OUT_R_1Cradle_R_OUT HP_OUT_L_AC REMOTE_JACK_1

43、 FM_OUT_L FM_OUT_R AUDIO_LDO_OUT PJ_In_T FM_AUDIO_DC_L HP_OUT_L_AC MIC_IN_1 FM_OUT_L FM_OUT_RFM_AUDIO_DC_R HP_OUT_L_1 PJ_In_T HP_OUT_R_AC HP_OUT_R_AC HP_OUT_L_1 HP_OUT_R_1 MIC_P_IN MIC_IN_1 +3.3V GND GND +3.3V GND GND GND GND +3.3V GND +3.3V +1.8V +3.3V +3.3V GND +3.3V GND +1.8V +1.8V GND JGNDRF_GND

44、 GND +3.3V +3.3V VCC_MEM +3.3V +3.3V GNDGND GND GND GNDGND GND Power_Out_C3,7 I2S_SDIN3 BM3_KSI43 I2C_DAT3,4,7,8 I2S_DOUT3 BM3_KSI123 BM3_KSI113 CLK_24M.CODEC3 ANT_SW1#3 BM3_KSI93,7 BM3_KSI33 BM3_KSI83 I2C_CLK3,4,7,8 BM3_KSI103 I2S_LRC3 BM3_KSI03 I2S_SCLK3 BM3_KSI53 BM3_KSI23 BM3_KSI13,7 DC- DC_STAR

45、T#4,5 BZZ_PWM3 HP_ANT8 TP_PWR#3 Cradle_R_OUT7 MUTE3 PJ_In3 REMOTE_JACK3,4 BZZ_CRL#3 FM_OUT_L8 FM_OUT_R8 Cradle_L_OUT7 Title Size Document Number Rev Date:Sheetof AUDIO / KEY MATRIXR00 C 68, 04, 2005星期四 八月 Title Size Document Number Rev Date:Sheetof AUDIO / KEY MATRIXR00 C 68, 04, 2005星期四 八月 Title Si

46、ze Document Number Rev Date:Sheetof AUDIO / KEY MATRIXR00 C 68, 04, 2005星期四 八月 I2C ADDRESS: 0011011 KEY MATRIX GPI DESCRIPTIONS MICROPHONE GPIO Touch Pad FUNCTION DESCRIPTIONS KSI0 KSI1 KSI2 KSI3 KSI4 KSI5 KSI6 KSI7 KSI8 KSI9 KSI10 KSI11 KSI12 Recording Volume up Volume down View Like Music xxxxx xx

47、xxx xxxxx HOLD xxxxx HOLD Buzzer ACK CLK DATA CLK ACK DATA No AGND=Check Solder point JGND is the Antenna using HeadPhone Cable Close to PhoneJack (J501) EMI two Cap.s removed for placement LED Current limit Check MIC_BIAS Check FPC Pin assignment Diff.with Arizona Phoenix DVT R0D 4/8 4/8 Check Size

48、 to smaller 4/14 default high Co-layout place R580 under the trace of Cradle_R_OUT; Dont out of the trace Pin E place on the trace ; No Branch Critical components PBSS2515F SOT523N PBSS2515F SOT523N only for Phoenix For Soft-star V(MICBIAS)=0.75*AVDD =0.75*1.8=1.35V Input Full Scale input to ADC: V(

49、INMIC)=1*AVDD/3.3=1.8/3.3=0.55V (max) Replace BUZZER MUX CONNECT CGND TO AGND VIA FERRITE BEAD AT THE JACK LC-CL to Swap Unuse if need to pull high or low?! 1 2 3 4 5 6 7 8 9 10 11 12GND1 GND2 J3 0.5MM/HDR/MA-12 MOLEX 54548- 1211 J3 0.5MM/HDR/MA-12 MOLEX 54548- 1211 12 R591 330 0402 5% R591 330 0402 5% 12 JO506 SPARKGAP_