Sony-BDVE385-hts-sm 电路图 维修手册.pdf

《Sony-BDVE385-hts-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-BDVE385-hts-sm 电路图 维修手册.pdf（102页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL Published by Sony EMCS (Malaysia) PG Tec Sony Corporation BLU-RAY DISC/DVD HOME THEATRE SYSTEM 9-890-583-01 2012C80-1 2012.03 US Model BDV-E385/E390/T39 Canadian Model BDV-E390 Ver. 1.0 2012.03 BDV-E385/E390/T39 are composed of following models. As service manuals are issued for each

2、component model, please refer to them. SPECIFICATIONS COMPONENT MODEL NAME BDV-E385BDV-E390BDV-T39 BLU-RAY DISC/ DVD receiver HBD-E385HBD-E390HBD-T39 Front speakerSS-TSB118SS-TSB118SS-TSB118 Center speakerSS-CTB113SS-CTB113SS-CTB113 Surround speakerSS-TSB118SS-TSB118SS-TSB118 SubwooferSS-WSB114SS-WS

3、B114SS-WSB114 Refer to next page for accessories list Unpacking Front speakers (2) Surround speakers (2) Center speakers (1) Subwoofer (1) FM wire antenna (aerial) (1) Remote commander (remote) (1) R6 (size AA) batteries (2) Dock for iPod/iPhone (TDM-iP30) (1) (BDV-E390/BDV-T39) USB cable (1) (BDV-E

4、390/BDV-T39) Video cord (1) High Speed HDMI cable (1) (BDV-T39) Operating Instructions Quick Setup Guide Speaker Installation Guide BDV-E385/E390/T39 ? iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Power requirements 1

5、20 V AC, 60 Hz Power consumption BDV-E385/BDV-E390/ BDV-T39 On: 130 W Standby: 0.3 W (at the Power Saving mode) Dimensions (approx.)430 mm 50 mm 275 mm (17 in 2 in 10 7/8 in) (w/h/d) incl. projecting parts Mass (approx.)2.8 kg (6 lb 2 3/4 oz) Design and specifications are subject to change without n

6、otice. ? Standby power consumption 0.3W. ? Over 85% power efficiency of amplifier block is achieved with the full digital amplifier, S-Master. RadioFans.CN 收音机爱 好者资料库 BDV-E385/E390/T39 2 ACCESSORIES 4-418-859-12 MANUAL, INSTRUCTION (ENGLISH (US) 4-418-859-22 MANUAL, INSTRUCTION (FRENCH) (CND) 4-418-

7、859-32 MANUAL, INSTRUCTION (SPANISH) (E385) 1 A-1797-336-A OVERALL ASSY (Dock for iPod/iPhone: TDM-iP30) (E390/T39) 2 1-489-949-11 REMOTE COMMANDER (including BATTERY LID) (RM-ADP072) 3 1-793-184-41 CONNECTOR (F TYPE ADAPTOR) (FM wire antenna (aerial) 4 1-756-988-21 BATTERY, MANGANESE (R6) 5 1-835-8

8、55-31 CORD WITH CONNECTOR (1.5m) (HDMI CAB (High Speed HDMI cable) (T39) 6 1-838-669-11 CORD, CONNECTION (1.2m) (Video cord) 7 1-839-590-11 CORD, CONNECTION (USB5P) (0.5m) (USB cable) (E390/T39) Ref. No. Part No. Description Remark Abbreviation CND : Canadian model 2 Remote commander (remote) (1) 5

9、High Speed HDMI cable (1) (T39) 4 R6 (size AA) batteries (2) 6 Video cord (1) 3 FM wire antenna (aerial) (1) or 1 Dock for iPod/iPhone (TDM-iP30) (1) (E390/T39) 7 USB cable (1) (E390/T39) RadioFans.CN 收音机爱 好者资料库 MEMO BDV-E385/E390/T39 3 RadioFans.CN 收音机爱 好者资料库 BDV-E385/E390/T39 REVISION HISTORY Chec

10、king the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver.DateDescription of Revision 1.02012.03New SERVICE MANUAL Sony Corporation Published by Sony EMCS (Malaysia) PG Tec SPECIFICATIONS BLU-RA

11、Y DISC/DVD RECEIVER 9-890-584-01 2012C80-1 2012.03 US Model HBD-E385/E390/T39 Canadian Model HBD-E390 Ver. 1.0 2012.03 HBD-E385 is the amplifi er, video, HDMI, BD/DVD/CD system, USB, LAN, wireless LAN and FM tuner section in BDV-E385. HBD-E390 is the amplifi er, video, HDMI, BD/DVD/CD system, USB, L

12、AN, wireless LAN and FM tuner section in BDV-E390. HBD-T39 is the amplifi er, video, HDMI, BD/DVD/CD system, USB, LAN, wireless LAN and FM tuner section in BDV-T39. Model Name Using Similar MechanismBDP-S390 Mechanism TypeBPX-7 Optical Pick-up Block NameKEM480AAA HBD-E385/E390/T39 Amplifier Section

13、BDV-E385/BDV-E390/BDV-T39 US models: AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (FTC) Front L + Front R:With 3 ohms loads, both channels driven, from 180 Hz - 20 kHz; rated 50 watts per channel minimum RMS power, with no more than 1% total harmonic distortion from 250 mil

14、li watts to rated output. Other models: POWER OUTPUT (rated) Front L/Front R:75 W + 75 W (at 3 ohms, 1 kHz, 1% THD) POWER OUTPUT (reference) Front L/Front R/Surround L/Surround R: 125 W (per channel at 3 ohms, 1 kHz) Center:250 W (at 6 ohms, 1 kHz) Subwoofer:250 W (at 6 ohms, 80 Hz) Inputs (Analog)

15、AUDIO (AUDIO IN)Sensitivity: 1 V/400 mV Inputs (Digital) TV (Audio Return Channel/OPTICAL) Supported formats: LPCM 2CH (up to 48 kHz), Dolby Digital, DTS Video Section OutputsVIDEO: 1 Vp-p 75 ohms HDMI Section ConnectorType A (19pin) BD/DVD/Super Audio CD/CD System Signal format systemNTSC USB Secti

16、on (USB) port:Type A (For connecting USB memory, memory card reader, digital still camera, and digital video camera) LAN Section LAN (100) terminal100BASE-TX Terminal Wireless LAN Section Blu-ray Disc/DVD receiver (HBD-E390/HBD- E385/HBD-T39) Standards ComplianceIEEE 802.11 b/g/n Frequency and Chann

17、el2.4 GHz - 2.4835 GHz CH1 -11 FM Tuner Section SystemPLL quartz-locked digital synthesizer Tuning range87.5 MHz - 108.0 MHz (100 kHz step) Antenna (aerial)FM wire antenna (aerial) Antenna (aerial) terminals 75 ohms, unbalanced General Power requirements 120 V AC, 60 Hz Power consumption BDV-E385/BD

18、V-E390/ BDV-T39 On: 130 W Standby: 0.3 W (at the Power Saving mode) Dimensions (approx.)430 mm 50 mm 275 mm (17 in 2 in 10 7/8 in) (w/h/d) incl. projecting parts Mass (approx.)2.8 kg (6 lb 2 3/4 oz) Design and specifications are subject to change without notice. ? Standby power consumption 0.3W. ? O

19、ver 85% power efficiency of amplifier block is achieved with the full digital amplifier, S-Master. Photo: HBD-E390 HBD-E385/E390/T39 2 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPE

20、RATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. This system incorporates with Dolby* Digital and Dolby Pro Logic adaptive matrix surround decoder and the DTS* Digital Surround System. * Manufactured under license

21、 from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories. * Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 LPCM 48kHz 2ch) 7. Diag (Wireless LAN Test) This screen

22、 performs wireless LAN test. Note: This mode doesnt operate correctly. Never use this mode. Refer to “CHECKING METHOD OF NETWORK OPERATION” on page 10 when you confi rm the wireless LAN operation. 8. Diag (MIC Input Test) This screen performs MIC input test. Note: Not used for the servicing. 9. Diag

23、 (HDMI Input Test) This screen performs HDMI input test. Note: Not used for the servicing. 10. Diag (Transcoder Test) Note: Not used for the servicing. 11. Log: Error Log (Output of each Log) This screen displays the contents of each log. Note: Do not refer to the displayed date. Screen 1: Selects l

24、og Operation: 1/ Moves to the Error Log output screen RETURN Returns to the top menu of the service mode Screen 2: Displays the Error Log Operation: Returns to the previous page , Moves to the next page RETURN Returns to the screen (Screen 1) that selects the log type RED Writes the log contents to

25、an USB memory device Viewing the log display Error Log: 174 2010/01/01 00:00:08: ErrCode:0902A4053002 Index number Date Time Error code About copying log to USB memory device: Press the RED button in each log display screen with the USB memory device inserted into the unit. Note: Please do not press

26、 the RED button immediately after USB mem- ory is inserted. Please do not pull out USB memory immediately after the RED button was pressed. Error Log: When “getErrLogFile.trm fi le” exists in the USB memory de- vice, errlog.log fi le is output. ? Diag Category: ? Diag Category: Audio Input Test Devi

27、ce: ENT Start Input Sound HELP: LEFT RIGHT UP DOWN ENT RET Audio Input Test Digital Input 1 Digital Input 2 Analog Input (Screen 1) (Screen 2) ? Diag Category: Audio Input Test Device: ENT Stop Input Sound HELP: LEFT RIGHT UP DOWN ENT RET Digital Input 1 Digital Input 2 Analog Input ? Select Log HEL

28、P : DOWNENT(NUM) ? Error Log 02 174 2010/01/01 00:00:08 ErrCode:0902A4053002 175 2010/01/01 00:00:08 ErrCode:0902A4053002 176 2010/01/01 00:00:08 ErrCode:0902A4053002 177 2010/01/01 00:00:08 ErrCode:0902A4053002 178 2010/01/01 00:00:08 ErrCode:0902A4053002 179 2010/01/01 00:00:08 ErrCode:0902A405300

29、2 180 2010/01/01 00:00:08 ErrCode:0902A4053002 181 2010/01/01 00:00:08 ErrCode:0902A4053002 182 2010/01/01 00:00:08 ErrCode:0902A4053002 183 2010/01/01 00:00:08 ErrCode:0902A4053002 184 2010/01/01 00:00:07 ErrCode:0902A4053002 185 2010/01/01 00:00:08 ErrCode:0902A4053002 186 2010/01/01 00:00:08 ErrC

30、ode:0902A4053002 HELP : Press RED key to store log to Udisc. 1 Error Log (Screen 1) (Screen 2) HBD-E385/E390/T39 25 12. Factory Initialize (Factory Settings) There is a possibility that this mode cannot be correctly executed. Never use this mode. 13. Network (Network Test Diagnosis Screen: Ifconfi g

31、) Network menu for the wired ethernet. Screen 1: Ifconfi g Test Operation: Activate Ifconfi g (Display network setting) , Select ping test RETURN Returns to the top menu of the service mode Screen 2: Ping Test Operation: Select Ifconfi g test RETURN Returns to the top menu of the service mode (The d

32、etails of a Ping test are “14. Network (Network Test Diagno- sis Screen: Ping)”) Screen 3: Ifconfi g Test Active Display Ifconfi g command results. Operation: Ifconfi g retry , Select Ping Test RETURN Returns to the top menu of the service mode 14. Network (Network Test Diagnosis Screen: Ping) Ping

33、test for the wired ethernet. Screen 1: Ping Test Operation: ” is reversed, the button is pressed and IP is inputted. Operation: Finish to input RETURN Finish to input Finish to input and Select Ifconfi g Test 0 to 9 Input Character sting 0-9 TIME Input Character sting . CLEAR Backspace Screen 3: Pin

34、g Test Active When START is reversed, the button is pressed and execute ping. Operation: Activate ping test M The IP address of the ping point is set up RETURN Returns to the top menu of the service mode 15. System Information (System Information Display) This screen displays system information. Scr

35、een 1: Basic Information Operation: , Drive information (delta IOP of a drive is measured) and wireless device information (E385/E390/T39) dis- played (go to Screen 2) RETURN Returns to the top menu of the service mode Screen 2: Drive and Wireless Information Menu Operation: 192. 168. 200. 13 ENT :

36、Release RET : Release (Screen 3) ? Network Ping to : 192. 168. 200. 13 START HELP: ENT : Start UP LEFT Ping Ifconfig Ping To : START ? Network Test: Ifconfig PING 192. 168. 200. 13 OK! Ping HBD-E385/E390/T39 26 Contents List: Main LSIname Model Destination Sequence Number MAC IP IFCON IFCON Version

37、Bootloader Bootloader Version Host Main Host Main Version MicroBE MicroBE Version Host Sub Host Sub Version Middleware Middleware Version ADSP ADSP Version ADSP Coeff ADSP Coeff Version 2nd DSP 2nd DSP Version (not used) IF Model IF Dest WLAN module Serial WLAN module hw Version WLAN module MAC Addr

38、ess Drive Firm Revision CD DIOP Delta IOP DVD DIOP Delta IOP BD DIOP Delta IOP CD LD TIME LD Time DVD LD TIME LD Time BD LD TIME LD Time 16. Drive This menu is used to operate the drive using drive-related diagnos- tic and tools. Screen 1: Selecting items under *Drive Operation: FUNCTION N 1 2 3 4 5

39、 6 7 8 9 PANEL BOARD 1-885-162- 11 (11) B MB148 BOARD CN602 (Page 35) C MB148 BOARD CN6303 (Page 35) T01 DC-DC CONVERTER TRANSFORMER DQSU corresponds to the data on DQU0-DQU7. The data strobe DQS, DQSL and DQSU are paired with differential signals DQS, DQSL and DQSU, respectively, to provide differe

40、ntial pair signaling to the system during reads and writes. DDR3 SDRAM supports differential data strobe only and does not support single-ended. B8DQU6I/OData Input/output: Bi-directional data bus. B9VSSQ-DQ Ground C1VDDQ-DQ Power Supply: 1.5V +/-0.075V C2DQU3I/OData Input/output: Bi-directional dat

41、a bus. C3DQU1I/OData Input/output: Bi-directional data bus. C4NO_USE-Not used C5NO_USE-Not used C6NO_USE-Not used C7DQSUI/O Data Strobe: Output with read data, input with write data. Edge-aligned with read data, centered in write data. For the x16, DQSL: corresponds to the data on DQL0-DQL7; DQSU co

42、rresponds to the data on DQU0-DQU7. The data strobe DQS, DQSL and DQSU are paired with differential signals DQS, DQSL and DQSU, respectively, to provide differential pair signaling to the system during reads and writes. DDR3 SDRAM supports differential data strobe only and does not support single-en

43、ded. C8DQU2I/OData Input/output: Bi-directional data bus. C9VDDQ-DQ Power Supply: 1.5V +/-0.075V D1VSSQ-DQ Ground D2VDDQ-DQ Power Supply: 1.5V +/-0.075V D3DMUI Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM is sampled HIGH coincident with that input data dur

44、ing a Write access. DM is sampled on both edges of DQS. For x8 device, the function of DM or TDQS/ TDQS is enabled by Mode Register A11 setting in MR1. D4NO_USE-Not used D5NO_USE-Not used D6NO_USE-Not used D7DQU0I/OData Input/output: Bi-directional data bus. D8VSSQ-DQ Ground D9VDD-Power Supply: 1.5V

45、 +/-0.075 E1VSS-Ground E2VSSQ-DQ Ground E3DQL0I/OData Input/output: Bi-directional data bus. E4NO_USE-Not used E5NO_USE-Not used E6NO_USE-Not used E7DMLI Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM is sampled HIGH coincident with that input data during a

46、Write access. DM is sampled on both edges of DQS. For x8 device, the function of DM or TDQS/ TDQS is enabled by Mode Register A11 setting in MR1. E8VSSQ-DQ Ground HBD-E385/E390/T39 74 Pin No.Pin NameI/ODescription E9VDDQ-DQ Power Supply: 1.5V +/-0.075V F1VDDQ-DQ Power Supply: 1.5V +/-0.075V F2DQL2I/

47、OData Input/output: Bi-directional data bus. F3DQSLI/O Data Strobe: Output with read data, input with write data. Edge-aligned with read data, centered in write data. For the x16, DQSL: corresponds to the data on DQL0-DQL7; DQSU corresponds to the data on DQU0-DQU7. The data strobe DQS, DQSL and DQS

48、U are paired with differential signals DQS, DQSL and DQSU, respectively, to provide differential pair signaling to the system during reads and writes. DDR3 SDRAM supports differential data strobe only and does not support single-ended. F4NO_USE-Not used F5NO_USE-Not used F6NO_USE-Not used F7DQL1I/OD

49、ata Input/output: Bi-directional data bus. F8DQL3I/OData Input/output: Bi-directional data bus. F9VSSQ-DQ Ground G1VSSQ-DQ Ground G2DQL6I/OData Input/output: Bi-directional data bus. G3DQSLI/O Data Strobe: Output with read data, input with write data. Edge-aligned with read data, centered in write data. For the x16, DQSL: corresponds to the data on DQL0-DQL7; DQSU corresponds to the data on DQU0-DQU7. The data strobe DQS, DQSL and DQSU ar