Philips-MCD-2010-Service-Manual(1) 电路图 维修手册.pdf

《Philips-MCD-2010-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-MCD-2010-Service-Manual(1) 电路图 维修手册.pdf（44页珍藏版）》请在收音机爱好者资料库上搜索。

1、Published by Sophie-KM 1135 AVMPrinted in the Netherlands MCD2010/12/93/98 Subject to modi cationEN Micro Audio System ContentsPageContentsPage Copyright 2011 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a

2、 retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Version 1.0 1 Technical Specification and Connection Facilities 2 Laser Beam Safety Precautions. 2-1 3 Important Safety Precautions . 3-1 to 3-2

3、4 Safety Check After Servicing . 4-1 6 Standard Notes For Servicing,Lead Free Requirements Rin 22k MP3_link(front) 750mV; Rin 22k IPOD Docking 750mV; Rin 22k Output Power(*1) At THD=10%, 1kHz sinewave MCD2010 Main Operation for / all version (rms) 10W 1dB ( At Cold Condition with 10% THD ) Tuner out

4、put power(rms) 10W 1dB ( At Cold Condition with 10% THD ) Frequency Response( 3dB) 30Hz-20kHZ Loudspeaker(Boxes): Separable speaker box Refer to package document of Speaker Box Assy Speaker driver Impedance: Right/Left: 6 30 Hz 20kHz(-3db) : refoowbuS REMARKS: Electrical Parameters are to be measure

5、d at Speaker Terminals across rated impedance Load(6ohm) with Rated Input Signal in CD Mode setting in DBB/Loudness Off and Pre-eq at Flat unless specified otherwise. Technical Specification and Connection Facilities 1-8 3.2.2 Video Performance 3.2.2.1 CVBS Description Test Signal Specification NTSC

6、 PAL Amplitude output 100% White 1Vpp 10% 1Vpp 10% %01 Vm007 %01 Vm417 et i hW %001 r ab et i hW %01 Vm003 %01 Vm682 et i hW %001 edut i l pmA . cnyS Burst Amplitude 75% Color bar 286mV, +1dB / - 4dB 300mV, +1dB / - 4dB Burst / chroma ratio 100% Color bar 5% 5% S/N luminance 100% White 60 dB 60 dB S

7、/N chroma AM PM 100% Red 57 dB 57 dB 60 dB 57 dB Video Bandwidth 0.5MHz 4MHz 4.8MHz 5.8MHz Multi-burst -1.5dB -5dB +1dB/-1dB -2dB -5dB Chroma Subcarrier Frequency 75% Color bar 3.579545 MHz 25ppm 4.433618MHz 30ppm Chroma / luminance delay 2T pulse 20ns 20ns Subcarrier locked/unlocked 75% Color bar l

8、ocked locked k ca lB %0 l eveL CD 1V 1V 3.2.2.2 Component Video (Y/Pb/Pr) Description Test Signal Specification Interlace/Progressive NTSC PAL %01 Vm0001 %01 Vm0001 et i hW %001 t uptuo edut i l pmA %01 Vm007 %01 Vm417 et i hW %001 r ab et i hW PbPr peak to peak 75% Color bar 525mV 10% 535mV 10% PbP

9、r Output unbalance 75% Color bar 3% 3% %01 Vm003 Vm04 Vm682 et i hW %001 edut i l pmA . cnyS S/N on outputs Y Pb / Pr 100% White 75% Color bar 60 dB 60 dB Video Bandwidth 4.2MHz 5.8MHz Multi-burst -1.5dB -5dB -1.5dB -5dB Video Bandwidth (Progressive) 8.4MHz 9.6MHz Multi-burst -1.5dB -5dB -1.5dB -5dB

10、 k c a l B %0 l eveL CD 1V 1V Technical Specification and Connection Facilities 1-9 3.3 TUNER FM use Silicon Lab Si4704/4705(w/RDS) GENARAL PART WAVE RANGE VERSIONTOLERANCE TUNING GRID FM 87.5 108.00 MHz /12 QUARTZ PRECISION 50kHz AERIAL FM : PIG TAIL ANT WIRE 75 ELECTRICAL DATA t i nU t im i L moN

11、MF fBd 62 02 tn i oP gn i t imi L Bd 3 - 14 53 )edom oeret s ta(y t i v i t i sneS gn i nuT hcraeS Search time digital tuning system. - 60 S zHM 7.01 FI Bd 15 84 gn i te i uQ Bd 64 - oeretS 54 05 muH no i ta l udoM 54 05 o i taR N/S Bd 4- 0 esreveR no i tac i f i l pmA % 3 2 ) zHk 57 . v eD qrF ,Vm1

12、 FR ( no i t rot s iD Overall Frequency Response: 63Hz 12.5KHz - 3 dB Channel separation:400 / 1000 / 5000 Hz. RF input: 68 dBf 26/30/ 20 20/26/ 18 dB Frequency (MHz) Noise Limited Sensitivity 26 dB Image Rejection IF Rejection Large Signal Handling Selectivity S9/300 kHz 22 0001 46 03 81.moN MF )1*

13、 ( 81 005 54 52 22.m i L 0.88 22 0001 46 03 81.moN MF )1* ( 81 005 54 52 22.m i L 0.89 54 fBd 611 06 03 81.moN MF 52 fBd 801 56 52 22.m i L 0.701 Units dBf DB dB mV/m dB Susceptibility to unwanted signals(CPU,SMPS,AMP,DSP ): Limited(d B) Normal (dB) Remark -15dB -20dB Refer to selfpollution curve Te

14、chnical Specification and Connection Facilities 1-10 Laser Beam Safety Precautions This Blu-Ray player uses a pickup that emits a laser beam. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup

15、lens when the diode is turned on. Do not look directly at the laser beam. CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure. Location: Inside Top of Blu-Ray mechanism. Do not look directly at the laser beam com

16、ing from the pickup or allow it to strike against your skin. Drive Mechanism Assembly Laser Beam Radiation Laser Pickup Turntable 2-1 Electronics N.V. bears no responsibility for improper wall mounting that results in accident, injury or damage. For speakers with stands, use only the supplied stands

17、. Secure the stands to the speakers tightly. Place the assembled stands on flat, level surfaces that can support the combined weight of the speaker and stand. Never place the product or any objects on power cords or on other electrical equipment. If the product is transported in temperatures below 5

18、C, unpack the product and wait until its temperature matches room temperature before connecting it to the power outlet. Visible and invisible laser radiation when open. Avoid exposure to beam. Do not touch the disc optical lens inside the disc compartment. Risk of overheating! Never install this pro

19、duct in a confined space. Always leave a space of at least four inches around the product for ventilation. Ensure curtains or other objects never cover the ventilation slots on the product. Risk of contamination! Do not mix batteries (old and new or carbon and alkaline, etc.). Remove batteries if th

20、ey are exhausted or if the remote control is not to be used for a long time. Batteries contain chemical substances, they should be disposed of properly. Product care Do not insert any objects other than discs into the disc compartment. Do not insert warped or cracked discs into the disc compartment.

21、 Remove discs from the disc compartment if you are not using the product for an extended period of time. Only use microfiber cloth to clean the product. Important Important Safety Precautions Read and understand all instructions before you use your home theater. If damage is caused by failure to fol

22、low instructions, the warranty does not apply. Safety Riskof electricshock or fire! Never expose the product and accessories to rain or water. Never place liquid containers, such as vases, near the product. If liquids are spilt on or into the product, disconnect it from the power outlet immediately.

23、 Contact Philips Consumer Care to have the product checked before use. Never place the product and accessories near nakedames or other heat sources, including direct sunlight. Never insert objects into the ventilation slots or other openings on the product. Where the mains plug or an appliance coupl

24、er is used as the disconnect device, the disconnect device shall remain readily operable. Disconnect the product from the power outlet before lightning storms. When you disconnect the power cord, always pull the plug, never the cable. Riskof short circuit orre! Before you connect the product to the

25、power outlet, ensure that the power voltage matches the value printed on the back or bottom of the product. Never connect the product to the power outlet if the voltage is different. Risk of injury or damage to the home theater! For wall-mountable products, use only the supplied wall mount bracket.

26、Secure the wall mount to a wall that can support the combined weight of the product and the wall mount. Koninklijke Philips 3-1 Caution: These servicing instructions are for use by qualified service personnel only.To reduce the risk of electric shock do not perform any servicing other than that cont

27、ained in the operating instructions unless you are qualified to do so. Disposal of your old product and batteries Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. When this crossed-out wheeled bin symbol is attached to a product

28、it means that the product is covered by the European Directive 2002/96/EC. Please inform yourself about the local separate collection system for electrical and electronic products. Please act according to your local rules and do not dispose of your old products with your normal household waste. Corr

29、ect disposal of your old product helps to prevent potential negative consequences for the environment and human health. Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed with normal household waste. Please inform yourself about the local rules on

30、separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health. Important Safety Precautions 3-2 4-1 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that scre

31、ws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards. 1. Clearance Distance When replacing primary circuit components, confirm specified clearance distance (d) and (d) betwe

32、en soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1) Table 1: Ratings for selected area Note:This table is unofficial and for reference only. Be sure to confirm the precise values. 2. Leakage Current Test Confirm the specified (or lower) leakage current between B

33、 (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below. Measuring Method (Power ON): Insert

34、load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across the terminals of load Z. See Fig. 2 and the following table. Table 2: Leakage current ratings for selected areas Note:This table is unofficial and for reference only. Be sure t

35、o confirm the precise values. AC Line VoltageClearance Distance (d), (d) 110V220V3.2 mm (0.126 inches) AC Line VoltageLoad ZLeakage Current (i)Earth Ground (B) to: 110V220V 0.15 F CAP. when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remov

36、e (glue will be melted). (Fig. S-1-6) 4.Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) CAUTION: 1.The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC. 2.Do not supply hot air to the

37、 chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2) Fig. S-1-1 Standard Notes for Servicing, Lead Free Requirements when removing entire flat pack-IC, first apply

38、soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 4.Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) With Iron Wire: 1.Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux whic

39、h is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 2.Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. 3.While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC

40、leads from the CBA contact pads as shown in Fig. S-1-5. 4.Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 5.Release the flat pack-IC from

41、 the CBA using tweezers. (Fig. S-1-6) Note:When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied. Hot-air Flat Pack-IC Desoldering Machin

42、e CBA Flat Pack-IC Tweezers Masking Tape Fig. S-1-2 Flat Pack-IC Desoldering Braid Soldering Iron Fig. S-1-3 Fine Tip Soldering Iron Sharp Pin Fig. S-1-4 To Solid Mounting Point Soldering Iron Iron Wire or Hot Air Blower Fig. S-1-5 Fine Tip Soldering Iron CBA Flat Pack-IC Tweezers Fig. S-1-6 6-3 Sta

43、ndard Notes for Servicing, Lead Free Requirements & Handling Flat Pack IC 2. Installation 1.Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. 2.The “” mark on the flat pack-IC indicates pin 1

44、. (See Fig. S-1-7.) Be sure this mark matches the 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.) 3.Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges. Instructions for Handling Semi- conductor

45、s Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 M ) that is properly grounded to remove any static electricity that may be charged on

46、the body. 2. Ground for Workbench Be sure to place a conductive sheet or copper plate with proper grounding (1 M ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be care

47、ful to avoid contacting semi-conductors with your clothing. Example : Pin 1 of the Flat Pack-IC is indicated by a mark. Fig. S-1-7 Presolder CBA Flat Pack-IC Fig. S-1-8 CBA Grounding Band Conductive Sheet or Copper Plate 1M 1M CBA Standard Notes for Servicing, Lead Free Requirements & Handling Flat

48、Pack IC 6-4 Direction of Use 7-1 *The following excerpt of the DFU/QSG serves as an introduction to the set. The Complete Direction for Use can be download in different languages from the internet site of Philips Customer care Center : Overview of the main unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 910 11 12 13 14 SOURCE Select a source. TUNING Rotate a photo. Fast backward or forward. Start or pause play. Stop play. Erase a program. PRESET Skip to the previous/next track, title, or file. Select a programmed radio station.