Sony-STRDA5800ES-rec-sm 电路图 维修手册.pdf

《Sony-STRDA5800ES-rec-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDA5800ES-rec-sm 电路图 维修手册.pdf（299页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL Sony Corporation Published by Sony Techno Create Corporation STR-DA5800ES SPECIFICATIONS MULTI CHANNEL AV RECEIVER 9-893-547-05 2014D33-1 2014.04 US Model Canadian Model AEP Model UK Model Taiwan Model Ver. 1.4 2014.04 Note: Be sure to keep your PC used for service and checking of thi

2、s unit always updated with the latest version of your anti-virus software. In case a virus affected unit was found during service, contact your Service Headquarters. AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL (US and Canadian models only) HARMONIC DISTORTION: With 8 ohm loads, both channels d

3、riven, from 20 20,000 Hz; rated 130 watts per channel minimum RMS power, with no more than 0.09% total harmonic distortion from 250 milliwatts to rated output. Amplifier section (US and Canadian models) (AEP, UK and Taiwan models) POWER OUTPUT1) 2) Rated Power Output at Stereo Mode (8 ohms 20 Hz 20

4、kHz, THD 0.09%): 130 W + 130 W Reference Power Output at Stereo Mode (4 ohms 20 Hz 20 kHz, THD 0.15%): 130 W + 130 W Reference Power Output (8 ohms 1 kHz, THD 0.7%) FRONT: 140 W + 140 W FRONT HIGH: 140 W + 140 W CENTER: 140 W SURROUND: 140 W + 140 W SURROUND BACK: 140 W + 140 W Reference Power Outpu

5、t (4 ohms 1 kHz, THD 0.7%) FRONT: 130 W + 130 W FRONT HIGH: 130 W + 130 W CENTER: 130 W SURROUND: 130 W + 130 W SURROUND BACK: 130 W + 130 W 1) Measured under the following conditions: Power requirements: 120 V AC, 60 Hz 2) Depending on the sound field settings and the source, there may be no sound

6、output. Frequency response3) Inputs (Analog) 3) When “A.Direct” is being used. Inputs (Digital) Outputs FM tuner section Tuning range87.5 MHz 108.0 MHz Antenna (aerial)FM wire antenna (aerial) Antenna (aerial) terminals 75 ohms, unbalanced AM tuner section (US and Canadian models) Antenna (aerial)Lo

7、op antenna (aerial) Video section Inputs/Outputs Video:1 Vp-p, 75 ohms COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms PB: 0.7 Vp-p, 75 ohms PR: 0.7 Vp-p, 75 ohms 80 MHz HD Pass Through PHONORIAA equalization curve 1.0 dB (20 Hz 20 kHz) MULTI CHANNEL INPUT, SA-CD/CD, MD/TAPE, TV, VIDEO 1/2, DVD, SAT/ CATV, GAME

8、 10 Hz 100 kHz 3 dB PHONOSensitivity: 2.5 mV Impedance: 50 kohms S/N3): 90 dB (A, 20 kHz LPF) MULTI CHANNEL INPUT, SA-CD/CD, MD/TAPE, TV, VIDEO 1/2, DVD, SAT/ CATV, GAME Sensitivity: 150 mV Impedance: 50 kohms S/N3): 105 dB (A, 20 kHz LPF. 500 mV) IN 1 (DVD), IN 2 (VIDEO 1), IN 3 (SA- CD/CD) (Coaxia

9、l) Impedance: 75 ohms S/N: 96 dB (A, 20 kHz LPF) IN 1 (GAME), IN 2 (SAT/CATV), IN 3 (TV) (Optical) S/N: 96 dB (A, 20 kHz LPF) MD/TAPE, VIDEO 1, ZONE 2, ZONE 3 (AUDIO OUT) Voltage:150 mV Impedance: 1 kohm FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK L/R, FRONT HIGH L/R, SUBWOOFER Voltage: 2 V Imped

10、ance: 1 kohm Tuning scaleTuning range 10 kHz step530 kHz 1,710 kHz 9 kHz step531 kHz 1,710 kHz HDMI Video Input/Output (HDMI Repeater block) D2tamroF 3D Frame packingSide-by-Side (Half) Over-Under (Top-and-Bottom) 4096 2160p 23.98/24 Hza 3840 2160p 29.97/30 Hza 3840 2160p 25 Hza 3840 2160p 23.98/24

11、Hza 1920 1080p 59.94/60 Hzaaa 1920 1080p 50 Hzaaa 1920 1080p 29.97/30 Hzaaaa 1920 1080p 25 Hzaaaa 1920 1080p 23.98/24 Hzaaaa 1920 1080i 59.94/60 Hzaaaa 1920 1080i 50 Hzaaaa 1280 720p 59.94/60 Hzaaaa 1280 720p 50 Hzaaaa 1280 720p 29.97/30 Hzaaaa 1280 720p 23.98/24 Hzaaaa 720 480p 59.94/60 Hza 720 576

12、p 50 Hza 640 480p 59.94/60 Hza Amplifier section POWER OUTPUT1) 2) Rated Power Output at Stereo Mode (8 ohms 20 Hz 20 kHz, THD 0.09%): 120 W + 120 W Reference Power Output at Stereo Mode (4 ohms 20 Hz 20 kHz, THD 0.15%): 120 W + 120 W Reference Power Output (8 ohms 1 kHz, THD 0.7%) FRONT: 130 W + 13

13、0 W FRONT HIGH: 130 W + 130 W CENTER: 130 W SURROUND: 130 W + 130 W SURROUND BACK: 130 W + 130 W Reference Power Output (4 ohms 1 kHz, THD 0.7%) FRONT: 120 W + 120 W FRONT HIGH: 120 W + 120 W CENTER: 120 W SURROUND: 120 W + 120 W SURROUND BACK: 120 W + 120 W 1) Measured under the following condition

14、s: Power requirements: 230 V AC, 50/60 Hz (AEP and UK models) (Taiwan model) Power requirements: 120V AC, 60 Hz 2) Depending on the sound field settings and the source, there may be no sound output. AM tuner section (AEP, UK and Taiwan models) Tuning scale9 kHz step Tuning range531 kHz 1,602 kHz Ant

15、enna (aerial)Loop antenna (aerial) Continued on next page RadioFans.CN 收音机爱 好者资料库 STR-DA5800ES 2 NOTES ON CHIP COMPONENT REPLACEMENT Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. SAFETY CHECK-OUT After correcting the original

16、service problem, perform the follow- ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal

17、part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manu

18、facturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog

19、meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth

20、 Ground Fig. A. Using an AC voltmeter to check AC leakage. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR A

21、S SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONC- TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES

22、SONY DONT LES NUMROS SONT DON- NS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS* Digital Surround System. *Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, Surround EX, and the double- D symbol

23、 are trademarks of Dolby Laboratories. * Manufactured under license under U.S. Patent Nos: 5,956,674, 5,974,380, 5,978,762, 6,487,535, 6,226,616, 7,212,872, 7,003,467, 7,272,567, 7,668,723, 7,392,195, 7,333,929, 7,548,853 1.25_16_M J-2501-347-A 1.2516 For CONTROL board (CN2781) 1.25_16_FFor A-VIDEO

24、board (CN6009) Flexible fl at cable 16PJ-2501-362-ALength 300 mm A-VIDEO BOARD SERVICE POSITION Please connect following extension jig. Connect extension jig 0 to the A-VIDEO board (CN6009) and CONTROL board (CN2781). A-VIDEO board (CN6009) insulating sheet CONTROL board (CN2781) alligator clip Note

25、: Connect altogether the metal part on the boards connected with the chassis using the alligator clip. Jig No.Jig NamePart No.Pitch (mm)CoresRemark qa 1.25_20_M J-2501-345-A 1.2520 For CONTROL board (CN2741) 1.25_20_FFor A AUDIO board (CN601) Flexible fl at cable 20PJ-2501-363-ALength 300 mm A AUDIO

26、 BOARD SERVICE POSITION Please connect following extension jig. CONTROL board (CN2741) insulating sheet A AUDIO board (CN601) Connect extension jig qa to the A AUDIO board (CN601) and CONTROL board (CN2741). alligator clip Note: Connect altogether the metal part on the boards connected with the chas

27、sis using the alligator clip. STR-DA5800ES 14 SECTION 2 DISASSEMBLY This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW 2-3. CASE BLOCK (Page 16) SET 2-16. D-AUDIO BOARD BLOCK-1 (Page 27) 2-11. D-VIDEO BOARD BLOCK-1 (Page 22) 2-12. D-VIDEO BOARD BLOCK-2 (Page 23) 2-18. NETWO

28、RK BOARD BLOCK-1 (Page 29) 2-19. NETWORK BOARD BLOCK-2 (Page 30) 2-22. CONTROL BOARD (Page 33) 2-23. A AUDIO BOARD-1 (Page 34) 2-24. A AUDIO BOARD-2 (Page 35) 2-25. BRACKET (LRG) BLOCK (Page 35) 2-21. A-VIDEO BOARD (Page 32) 2-17. D-AUDIO BOARD BLOCK-2 (Page 28) 2-13. D-VIDEO BOARD (Page 24) 2-20. N

29、ETWORK BOARD (Page 31) 2-4. SUB D-VIDEO BOARD BLOCK-1 (Page 17) 2-15. D-AU_CONNECT BOARD (Page 26) 2-33. DC FAN (M2) (Page 42) 2-36. E-VOL BOARD (Page 45) 2-5. SUB D-VIDEO BOARD BLOCK-2 (Page 18) 2-6. SUB D-VIDEO BOARD (Page 18) 2-7. HAT BOARD (Page 19) 2-8. USB-DDC BOARD (AEP, UK and Taiwan models)

30、 (Page 20) 2-9. TUNER BLOCK (Page 21) 2-10. TUNER ASSY (TU1) (Page 21) 2-14. HDMI CABLE (HDC1) (Page 25) 2-2. HOW TO BEND WIRE (FLAT TYPE) (Page 15) to page 15 A to page 15 C to page 15 B Ver. 1.2 STR-DA5800ES 15 2-2. HOW TO BEND WIRE (FLAT TYPE) 2-26. DCDC2 BOARD (Page 36) from page 14 A from page

31、14 B from page 14 C 2-31. SB-SPTM BOARD (Page 41) 2-32. SPTM BOARD (Page 41) 2-27. ACDC/DCDC BOARD BLOCK (Page 37) 2-29. STBY BOARD (Page 39) 2-28. DCDC BOARD (Page 38) 2-30. POWER TRANSFORMER (T001) (Page 40) 2-34. HEAT SINK BLOCK-1 (Page 43) 2-35. HEAT SINK BLOCK-2 (Page 44) 2-37. FRONT PANEL BLOC

32、K-1 (Page 46) 2-39. MAIN BOARD BLOCK (Page 47) 2-40. MAIN BOARD (Page 48) 2-38. FRONT PANEL BLOCK-2 (Page 47) ? D-VIDEO board (CN3510) CONTROL board (CN2861) 80 2 mm STR-DA5800ES 16 Note: Follow the disassembly procedure in the numerical order given. 2-3. CASE BLOCK 4 4 5 6 7 case block 3 screw (BTP

33、) (DIA. 3) 1 two screws (BVST4 ? 8) 2 two screws (BVTP3 ? 8) 1 two screws (BVST4 ? 8) STR-DA5800ES 17 2-4. SUB D-VIDEO BOARD BLOCK-1 1 Cut the cable tie. (See Fig. A) 1 Cut the cable tie. (See Fig. A) 1 Cut the cable tie. (See Fig. A) cable tie cable tie 3 HDMI cable (HDC2) (CN3700) (See Fig. A) HDM

34、I cable (HDC2) 5 HDMI cable (HDC1) (CN3701) 6 connector (CN7511) 2 Remove wires from clamp (L35). (See Fig. A) clamp (L35) heat sink 4 tape (See Fig. B) SUB D-VIDEO board D-VIDEO board Note 1: In reassembling, use new cable tie to fasten the clamp same as before. Note 3: The wire must not touch heat

35、 sinks. Note 3: The wire must not touch heat sinks. Note 3: The wire must not touch heat sinks. Note 2: Stuff wires into the rear panel. heat sink heat sink heat sink heat sink SUB D-VIDEO board D-VIDEO board cable tie Rear side Rear side wire (flat type) (19 core) (FFC1) tapeSUB D-VIDEO board ?Wire

36、 setting (AEP, UK, TW) (US, CND) (US, CND) (AEP, UK, TW) (AEP, UK, TW) 30 mm Abbreviation CND : Canadian model TW : Taiwan model Ver. 1.2 STR-DA5800ES 18 2-5. SUB D-VIDEO BOARD BLOCK-2 4 screw (BVTP3 ? 8) 4 screw (BVTP3 ? 8) 5 SUB D-VIDEO board block 3 four screws (B3 ? 5) 1 Push two buttons of conn

37、ector. 2 flexible flat cable (CN7001) 2-6. SUB D-VIDEO BOARD 1 screw (BVTP3 ? 8) 1 screw (BVTP3 ? 8) 1 screw (BVTP3 ? 8) 2 clamp (L35) 4 bracket (S-HDMI) 5 SUB D-VIDEO board 3 bracket (S-HDMI2) 1 screw (BVTP3 ? 8) 2 clamp (L35) (AEP, UK, TW) (AEP, UK, TW) Ver. 1.2 Abbreviation TW : Taiwan model STR-

38、DA5800ES 19 2-7. HAT BOARD 1 connector (CN2941) 4 Remove the HAT board in the direction of an arrow. 6 HAT board 2 screw (BVTP3 ? 8) 3 two nuts (supplied with J861) J861 5 wire (flat type) (19 core) (FFC1) (CN807) J861 is not slanting. J861 is slanting. OKNG colored line colored line Insert is strai

39、ght to the interior.Insert is incline wire (flat type) wire (flat type) connectorconnector OKNG Note 1: When installing the wire (flat type), ensure the colored line. No slanting after insertion. Note 2: When installing the HAT board, check that J861 is installed correctly. STR-DA5800ES 20 2-8. USB-

40、DDC BOARD (AEP, UK and Taiwan models) 1 two screws (BVTP3 ? 8) 3 Remove the USB-DDC board block in the direction of an arrow. 5 USB-CONNECT board 6 USB-DDC board 2 connector (CN102) 4 connector (CN101) (AEP, UK) Note 1: When replacing the complete USB-DDC board, refer to “NOTE OF REPLACING THE COMPL

41、ETE USB-DDC BOARD” (page 6). Note 2: The USB-CONNECT board installed in AEP and UK models has been deleted in the midway of production, and the D-AUDIO and USB-DDC boards have been changed into connection with the wire (AEP and UK models only). (Taiwan model does not use USB- CONNECT board in the fi

42、 rst time of production, and the D-AUDIO and USB-DDC boards are connection with the wire) Ver. 1.2 STR-DA5800ES 21 2-9. TUNER BLOCK 2-10. TUNER ASSY (TU1) 3 Remove the tuner block in the direction of an arrow. 4 tuner block colored line colored line Insert is straight to the interior. Insert is incl

43、ine wire (flat type) wire (flat type) connector connector OK NG Note: When installing the wire (flat type), ensure the colored line. No slanting after insertion. 2 two screws (BVTP3 ? 8) 1 wire (flat type) (9 core) (CN2692) 6 tuner assy (TU1) tuner assy (TU1) tuner assy (TU1) colored line colored li

44、ne Insert is straight to the interior. Insert is incline wire (flat type) wire (flat type) connector connector OK NG Note: When installing the wire (flat type), ensure the colored line. No slanting after insertion. 2 wire (flat type) (9 core) (FFC2) wire (flat type) (9 core) (FFC2) 3 ferrite core (F

45、C1) 4 ferrite core (FC2) ferrite core (FC1)ferrite core (FC2) 1 saranet cushion (LXWXT) saranet cushion (LXWXT) 5 spacer ? spacer guide line guide line ? Ferrite core (FC2) has not ridden on the connector. Ferrite core (FC2) has ridden on the connector. ? OKNG STR-DA5800ES 22 2-11. D-VIDEO BOARD BLO

46、CK-1 1 connector (CN3571) 6 connector (CN3509) (See Fig. C) 8 connector (CN3607) (See Fig. C) 0 connector (CN3523) (See Fig. D) 3 connector (CN3511) 2 wire (flat type) (13 core) (CN3510) 5 Remove wires from lead pin. (See Fig. C) lead pin SB-SPTM board D-VIDEO board D-VIDEO board 7 Remove the wire f

47、rom clamp (L35). (See Fig. C) clamp (L35) clamp (L35)lead pin SB-SPTM board heat sink Note 3: The wire must not touch heat sinks. Note 3: The wire must not touch heat sinks. Note 3: The wire must not touch heat sinks. Rear side Rear side D-VIDEO board heat sink heat sink ? Wire setting colored line

48、colored line Insert is straight to the interior.Insert is incline wire (flat type) wire (flat type) connectorconnector OKNG Note 2: When installing the wire (flat type), ensure the colored line. No slanting after insertion. Note 1: In reassembling, use new cable tie to fasten the clamp same as befor

49、e. (AEP, UK, TW) 9 Cut the cable tie. (See Fig. D) 4 Cut the cable tie. (See Fig. C) cable tie cable tie (US, CND) (AEP, UK, TW) Abbreviation CND : Canadian model TW : Taiwan model Ver. 1.2 STR-DA5800ES 23 2-12. D-VIDEO BOARD BLOCK-2 1 seven screws (B3 ? 5) 2 screw (BVTP3 ? 8) 2 screw (BVTP3 ? 8) 2 screw (BVTP3 ? 8) 3 clamp (L35) B A