Sony-STRDA80ES-rec-sm 电路图维修手册.pdf

上传人：cc518

文档编号：238026

上传时间：2025-10-12

格式：PDF

页数：66

大小：11.34MB

《Sony-STRDA80ES-rec-sm 电路图维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDA80ES-rec-sm 电路图维修手册.pdf（66页珍藏版）》请在收音机爱好者资料库上搜索。

1、1) Depending on the sound field settings and the source, sound will not be output. Dynamic power output 155 W + 155 W, 8 ohms 220 W + 220 W, 4 ohms (STR-DA80ES: US, Canadian) Harmonic distortion at rated output STR-DA80ES: Less than 0.05 % (with DIRECT PASS on) TA-V88ES/TA-VA80ES: Less than 0.7 % (w

2、ith DIRECT PASS on) Frequency response PHONO: RIAA equalization curve 0.5 dB CD, TAPE, DAT/MD, VIDEO 1, 2, 3, LD/DVD, TV (/DBS): 10 Hz-50 kHz dB (with DIRECT PASS on) +0.5 2 MICROFILM US Model Canadian Model STR-DA80ES AEP Model UK Model TA-VA80ES E Model STR-DA80ES/TA-VA80ES Australian Model PX Mod

3、el STR-DA80ES Chinese Model TA-V88ES SPECIFICATIONS SERVICE MANUAL STR-DA80ES/TA-V88ES/TA-VA80ES Manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby,” the double-D symbol a, “AC-3” and “Pro Logic” are trademarks of Dolby Laboratories Licensing Corporation. Photo: STR-DA8

4、0ES STR-DA80ES FM STEREO/FM-AM RECEIVER TA-V88ES/TA-VA80ES INTEGRATED AV AMPLIFIER AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 8-ohm load, both channels driven, from 20-20,000 Hz, rated 100 watts per channel, minimum RMS power, with no more than 0.09 % total harmonic d

5、istorition from 250 milliwatts to rated output (US model). Amplifier section POWER OUTPUT Stereo modeSTR-DA80ES: (8 ohms 20 Hz-20 kHz, THD 0.05 %) 100 W + 100 W TA-V88ES: (6 ohms at 1 kHz, THD 0.7%) 100 W + 100 W TA-VA80ES: (4 ohms at 1 kHz, THD 0.7%) 100 W + 100 W Surround modeSTR-DA80ES: (8 ohms a

6、t 1 kHz, THD 0.05 %) Front: 100 W + 100 W Center1): 100 W Rear1): 100 W + 100 W TA-V88ES: (6 ohms at 1 kHz, THD 0.7%) Front: 100 W + 100 W Center1): 100 W Rear1): 100 W + 100 W TA-VA80ES: (4 ohms at 1 kHz, THD 0.7%) Front: 100 W + 100 W Center1): 100 W Rear1): 100 W + 100 W Inputs S/N Sensitivity Im

7、pedance (weighting network, input level) PHONO2.5 mV 5075 dB kilohms(A, 2.5 mV) 200 mV CD (STR-DA80ES) 150 mV (TA-V88ES/VA80ES) TAPE, DAT/200 mV5082 dB MD, VIDEO(STR-DA80ES)kilohms(A, 150 mV) 1, 2, 3150 mV LD, TV/DBS(TA-V88ES/VA80ES) TUNER150 mV (TA-V88ES/VA80ES) LD DVD 75 100 dB AC-3 RF IN(A, 20 kH

8、z, LPF) LD DVD COAXIAL0.5 Vp-p75 100 dB IN (A, 20 kHz, LPF) LD DVD/TV (DBS)/CD/ 100 dB DAT MD(A, 20 kHz, LPF) OPTICAL IN RadioFans.CN 收音机爱好者资料库 2 +0.5 2 OutputsREC OUT: DAT/MD, TAPE Voltage: 200 mV (STR-DA80ES) 150 mV (TA-V88ES/VA80ES) Impedance: 1 kilohm AUDIO OUT: VIDEO 1, 2 Voltage: 200 mV (STR-

9、DA80ES) 150 mV (TA-V88ES/VA80ES) Inpedance: 1 kilohm PRE OUT: Voltage: 2 Vrms Impedance: 1 kilohm PHONES: Accepts low and high impedance headphones BASS BOOST+6 dB at 70 Hz (STR-DA80ES) +10 dB at 70 Hz (TA-V88ES/VA80ES) Digital signal processor section Modulation (A/D conversion) High Density Linear

10、 Converter Demodulation (D/A conversion) High Density Linear Converter (Advanced pulse D/A converter) Sampling frequency 48 kHz SurroundLFE MIX: MUTE, 20 - 0 dB, 0.5 dB step D.RANGE COMP: OFF, 0.1 - 0.9, STD, MAX REAR level: 20 - +10 dB, 0.5 dB step CENTER level: 20 - +10 dB, 0.5 dB step SUB WOOFER

11、level: 20 - +10 dB, 0.5 dB step EFFECT: 21-step adjustable WALL: 17-step adjustable SEAT F/R: 17-step adjustable L/R: 17-step adjustable REBERB time: 17-step adjustable EqualizerBAND: BASS/TREBLE Turnover frequency: Bass: 99 Hz-992 Hz Treble: 1.0 kHz-8.6 kHz Level: 10 dB, 0.5 dB step FM tuner sectio

12、n (STR-DA80ES) Tuning range 87.5-108.0 MHz Antenna terminals 75 ohms, unbalanced SensitivityMono: 18.3 dBf, 4.5 V Stereo: 38.3 dBf, 45 V Usable sensitivity 11.2 dBf, 2 V (IHF) S/NMono: 76 dB Stereo: 70 dB Harmonic distortion at 1 kHz Mono: 0.3 % Stereo: 0.5 % Separation45 dB at 1 kHz Frequency respo

13、nse 30 Hz-15 kHz dB Selectivity60 dB at 400 kHz AM tuner section (STR-DA80ES) Tuning range With 10 kHz interval: 530-1710 kHz (US and Canadian models3) 530-1610 kHz (models for all other countries except for Australia) With 9 kHz interval: 531-1710 kHz (US and Canadian models) 531-1602 kHz (Australi

14、an model and models for all other countries3) AntennaLoop antenna Usable sensitivity 50 dB/m (at 1,000 kHz or 999 kHz) S/N54 dB (at 50 mV/m) Harmonic distortion 0.5 % (50 mV/m, 400 kHz) SelectivityAt 9 kHz: 35 dB At 10 kHz: 40 db 3) You can change the AM tuning interval to 9 kHz (US and Canadian mod

15、els) or to 10 kHz (models for all other countries except for Australia). After tuning in any AM station, turn off the receiver. Hold down the PRE- SET TUNING + button and press the POWER button. All preset stations will be erased when you change the interval. To re- set the interval to 10 kHz (or 9

16、kHz), repeat the procedure. Video section InputsVIDEO: 1 Vp-p 75 ohms S VIDEO: Y: 1 Vp-; 75 ohms C: 0.286 Vp-p 75 ohms OutputsVIDEO: 1 Vp-p 75 ohms S VIDEO: Y: 1 Vp-p 75 ohms C: 0.286 Vp-p 75 ohms General SystemTuner section: PLL quartz-locked digital synthesizer system (STR-DA80ES) Preamplifier sec

17、tion: Low-noise NF type equalizer Power amplifier section: Pure-complementary parallel P.P. Power requirements US and Canadian models: 120 V AC, 60 Hz Australian model: 240 V AC, 50 Hz European models: 230 V AC, 50 Hz Other models: 120/220/240 V AC selectable, 50/60 Hz Power consumption STR-DA80ES:

18、US model: 340 W Canadian model: 500 VA Australian model: 380 W Other models: 380 W TA-V88ES: 370 W TA-VA80ES: 380 W AC outletsSTR-DA80ES: US and Canadian models: 2 switched, total 120 W Australian model: 1 switched, maximum 100 W Other models: 2 switched, total 100 W TA-V88ES/VA80ES: 1 switched, max

19、imum 100 W Dimensions430 160 435 (4404) mm (17 63/8 17 1/4 (17 3/8) inches) including projecting parts and controls 4) When the front cover is open Mass (Approx.) 15.9 kg (35 Ib 1 oz) (STR-DA80ES) 15.6 kg (TA-V88ES/VA80ES) Supplied accessories FM wire antenna (1) (STR-DA80ES) AM loop antenna (1) (ST

20、R-DA80ES) Remote commander RM-P501 (remote) (1) Size AA (R6) batteries (2) Design and specifications are sbuject to change without notice. RadioFans.CN 收音机爱好者资料库 3 TABLE OF CONTENTS 1.GENERAL. 4 2.DISASSEMBLY. 7 3.ELECTRICAL ADJUSTMENTS.9 4.DIAGRAMS 4-1.IC Pin Function Description. 10 4-2.Schematic

21、 Diagram DISPLAY Section . 24 4-3.Printed Wiring Boards DISPLAY Section . 29 4-4.Schematic Diagram VIDEO Section . 33 4-5.Printed Wiring Boards VIDEO Section . 37 4-6.Schematic Diagram INPUT/TUNER/POWER Section . 41 4-7.Printed Wiring Boards INPUT/TUNER/POWER Section . 45 4-8.Schematic Diagram DIGIT

22、AL Section . 50 4-9.Printed Wiring Boards DIGITAL Section . 55 4-10. Schematic Diagram AMP/OUTPUT Section . 59 4-11. Printed Wiring Boards AMP/OUTPUT Section . 63 5.EXPLODED VIEWS. 69 6.ELECTRICAL PARTS LIST. 74 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MA

23、RK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE

24、 ! SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. MODEL IDENTIFICATION BACK PANEL STR-DA80ES US Model: 373-3 S

25、TR-DA80ES Canadian Model : 373-4 STR-DA80ES Australian Model : 373-5 STR-DA80ES E, PX Model: 373-6 TA-V88ESChinese Model: 374-4 TA-VA80ESAEP, UK, German, EE, CIS Model: 374-0 TA-VA80ESE, Malaysia, Singapore Model : 374-3 SAFETY CHECK-OUT After correcting the original service problem, perform the fol

26、low- ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from al

27、l exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use thes

28、e instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indica- tion is 0.75 V, so analog meters must have an accurate low-

29、voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex- amples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suit- able. (See Fig. A) Fig. A.Using an AC voltmeter to check AC leakage. 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Met

30、al Parts on Set Earth Ground 4-991- RadioFans.CN 收音机爱好者资料库 4 This section is extracted from instruction manual. SECTION 1 GENERAL STR-DA80ES Front Panel Description 5 TA-V88ES Front Panel Description 6 TA-VA80ES Front Panel Description 7 Note: Follow the disassembly procedure in the numerical order

31、 given. CASE SECTION 2 DISASSEMBLY REAR PANEL SECTION 1 two screws (M 3 8) 3 case 1 three screws (M 3 8) 1 three screws (M 3 8) 1 two screws (M 3 8) 2 2 1 connector (CNE910) 1 connector (CNV903) 1 connector (CNV902) 3 two screws (BVTP 3 6) 4 back panel section 2 seven screws (BVTP 3 8) 1 connector (

32、CNE807) 2 two screws (BVTP 3 8) (STR-DA80ES) 2 eight screws (BVTP 3 8) 2 seven screws (BVTP 3 8) 1 connector (CND3503) 2 four screws (BVTP 3 8) 2 screw (BVTP 3 8) 8 TUNER/AUDIO/SPTM BOARD, FRONT PANEL SECTION INPUT BOARD 1 connector (CNV613) 2 five screws (BVTP 3 8) 1 connector (CNE939) 2 two screws

33、 (BVTP 3 8) 4 INPUT board 3 claw 1 five connectors (CNE601, 620, 622, 3501, ) CNP202 1 five connectors (CND621, CNE601, 602, ) CNV615, 616 1 connector (CNE211) 1 connector (CNS210) 1 connector (CNS623) 7 four screws (BVTP 3 8) 8 front panel section 2 SPTM board 5 connector (CNS201) 6 TUNER board 7 t

34、hree screws (BVTP 3 8) 4 flat wire (CNS3503) 3 AUDIO board STR-DA80ES 9 DC BIAS CURRENT Adjustment (with no signal input) Note: 1.DC BIAS CURRENT adjustments should be made 30 seconds after the POWER switch is turned on (POWER ON). 2.After replacing the power transistors, DC BIAS CURRENT adjustments

35、 should be perfomed. Procedure: Digital volt meter + 1 2 3 R615 R665 R016 R715 R765 AMP BOARD AMP BOARD (COMPONENT SIDE) R665 RV651 1 2 3 D973 D971 D972 C987 C988 C985 C986 1 2 3 R668 R765 RV751 R017 R768 RV001 R016 R715 RV701 R718 R615 RV601 R618 3 2 1 32 1 1 2 3 FRONT Rch REAR Rch FRONT Lch REAR L

36、ch CENTER ConnectingAdjustmentReading on pointpartDigital volt meter FRONT LchR615RV60120 mV FRONT RchR665RV65120 mV CENTERR016RV00120 mV REAR LchR715RV70120 mV REAR RchR765RV75120 mV SECTION 3 ELECTRICAL ADJUSTMENTS 10 1MBUS (VZ)INot used (fixed at “L”) 2MBUS (MON)INot used (fixed at “L”) 3MBUS (ST

37、U)ONot used (open) 4LED-V3OLED drive signal output terminal“H”: LED on(for function VIDEO 3 indicator) 5LED-V2OLED drive signal output terminal“H”: LED on(for function VIDEO 2 indicator) 6LED-V1OLED drive signal output terminal“H”: LED on(for function VIDEO 1 indicator) 7STANDBYOLED drive signal out

38、put terminal“H”: LED on(for function STANDBY indicator) 8DPC (SURR)OLED drive signal output terminal“H”: LED on(for function SUR indicator) 9DPC (EQ)OLED drive signal output terminal“H”: LED on(for function EQ indicator) 10DPC (INDEX)OLED drive signal output terminal“H”: LED on(for function INDEX in

39、dicator) 11DVSSGround terminal 12LED-CEOLED drive signal output terminal “H”: LED on(for function CD indicator) 13LED-DAT/MDOLED drive signal output terminal“H”: LED on(for function DAT/MD indicator) 14LED-TAPEOLED drive signal output terminal“H”: LED on(for function TAPE indicator) 15LED-TVO LED dr

40、ive signal output terminal“H”: LED on (for function TV/DBS (STR-DA80ES) or TV (TA-V88ES/VA80ES) indicator) 16LED-LDOLED drive signal output terminal“H”: LED on(for function LD/DVD indicator) 17LED-V3OLED drive signal output terminal“H”: LED on(for function VIDEO 3 indicator) 18LED-V2OLED drive signa

41、l output terminal“H”: LED on(for function VIDEO 2 indicator) 19LED-V1OLED drive signal output terminal“H”: LED on(for function VIDEO 1 indicator) 20RX (SIN)IReceive data input from the on screen display controllerNot used (fixed at “L”) 21TX (SOUT)OTransmit data output to the on screen display contr

42、ollerNot used (open) 22BUSYIBusy signal input from the on screen display controllerNot used (fixed at “L”) 23FL CLEARO“Display clear signal output to the fluorescent indicator tube driver (IC101, 102)” 24FL DATAOSerial data output to the fluorescent indicator tube driver (IC102) 25FL CLKO“Serial dat

43、a transfer clock signal output to the fluorescent indicator tube driver (IC101, 102)” 26LAT (OSD)O“Serial data latch pulse signal output to the fluorescent indicator tube driver (IC101, 102)” 27SIRCS1ISircs signal input from the remote control receiver (IC104) 28AVCCPower supply terminal (+5V) 29AVR

44、+IReference voltage input terminal (+5V) 30AVRIReference voltage input terminal (+0V) 31GNDGround terminal 32AD KEY IN 1I Key input terminal (A/D input) S132 to 134 (INPUT MODE, DIRECT PASS, BASS BOOST keys) Key input terminal (A/D input) 33AD KEY IN 2IS116 to 119 (FM/AM, SHIFT, PRESET TUNING +/ key

45、s) (STR-DA80ES). Not used (open) (TA-V88ES/VA80ES) 34DVSSGround terminal Key input terminal (A/D input) 35AD KEY IN 3I S109 to 114 (STR-DA80ES: EQUALIZER BAND, TUNING +/, FM MODE, MEMORY, DISPLAY keys) (TA-V88ES/VA80ES: EQUALIZER BAND, EQUALIZER ON/OFF, SOUND FIELD STANDARD, SLEEP, DIMMER) 36AD KEY

46、IN 4I Key input terminal (A/D input) S101 to 108 (EQUALIZER CH, DPC MODE, cursor /, SET UP, OPEN/CLOSE keys) 37AD KEY IN 5I Key input terminal (A/D input) S129 to 131 (MODE, SOUND FIELD ON/OFF, GENRE keys) 38AD VERSIONISetting terminal for the destination (A/D input) 39VOL-UPIMotor drive signal inpu

47、t for the master volume 40VOL-DOWNIMotor drive signal input for the master volume DISPLAY BOARD IC105 MB90673PF-G-206-BND (FLUORESCENT INDICATOR TUBE DRIVE CONTROLLER, KEY CONTROL) Pin No.Pin NameI/OFunction SECTION 4 DIAGRAMS 4-1.IC Pin Function Description 11 Pin No.Pin NameI/OFunction 41MODE0IMod

48、e selection terminal (fixed at “H”) 42MODE1IMode selection terminal (fixed at “H”) 43MODE2IMode selection terminal (fixed at “L”) 44STANDBYIHardware standby signal input terminal (fixed at “H”) 45STOPIStop signal input terminal 46U-RESETISystem reset signal input from the master controller (IC3413) “L”: reset 47U-SREQOCommunication request signa