Sony-STSE570-tun-sm 电路图 维修手册.pdf
《Sony-STSE570-tun-sm 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Sony-STSE570-tun-sm 电路图 维修手册.pdf(24页珍藏版)》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL FM STEREO FM-AM TUNER AEP Model UK Model SPECIFICATIONS ST-SE570 Ver 1.0 2001.04 9-873-834-11Sony Corporation 2001D0500-1Home Audio Company C 2001.4Shinagawa Tec Service Manual Production Group FM tuner section Frequency range87.5 - 108.0 MHz (50 kHz step) Aerial terminals75 , unbalan
2、ced IEC-male Intermediate frequency 10.7 MHz Sensitivityat 26 dB quieting (mono) 10.3 dBf, 0.9 V/75 at 46 dB quieting (stereo) 38.5 dBf, 23 V/75 Usable sensitivity (IHF) 10.3 dBf, 0.9 V/75 S/Nat 40 kHz deviation 74 dB (mono), 69 dB (stereo) Harmonic distortion0.09% (mono), 0.18% (stereo) Frequency r
3、esponse30 Hz - 15 kHz (+0.5/1.0 dB) Separation45 dB at 1 kHz Selectivityat 400 kHz 85 dB at 300 kHz 70 dB Outputat 40 kHz deviation 600 mV AM tuner section Frequency range MW:522 - 1,611 kHz (9 kHz step) LW:144 - 288 kHz (1 kHz step) Intermediate frequency 450 kHz Usable Sensitivity(with AM loop aer
4、ial) MW:200 V/m LW:700 V/m Signal-to-noise ratio MW:54 dB (50 mV/m, 999 kHz) LW:50 dB (50 mV/m, 216 kHz) Harmonic distortion0.3% (50 mV/m, 400 Hz) Selectivity50 dB General Power requirements230 V AC, 50/60 Hz Power consumption10 W Dimensions430 x 83 x 290 mm (w/h/d) Weight2.5 kg Supplied accessories
5、 Audio cord (1) AM loop antenna (1) FM wire antenna (1) EON connecting cord (1) Design and specifications are subject to change without notice. RadioFans.CN 收音机爱 好者资料库 2 ST-SE570 TABLE OF CONTENTS 1.GENERAL.3 2.DISASSEMBLY 2-1.Disassembly Flow .4 2-2.Case (407026) .4 2-3.MAIN Board .5 3.TEST MODE.6
6、4.ELECTRICAL ADJUSTMENTS.8 5.DIAGRAMS 5-1.Note for Printed Wiring Boards and Schematic Diagrams .9 5-2.Printed Wiring Boards MAIN Section . 10 5-3.Schematic Diagram MAIN Section . 11 5-4.Printed Wiring Boards DISPLAY Section . 12 5-5.Schematic Diagram DISPLAY Section . 13 5-6.IC Pin Function Descrip
7、tion . 14 6.EXPLODED VIEWS 6-1.Case Section . 16 6-2.Front Panel Section . 17 6-3.Chassis Section . 18 7.ELECTRICAL PARTS LIST. 19 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATI
8、ON. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY. RadioFans.CN 收音机爱 好者资料库 3 ST-SE570 SECTION 1 GENERAL This section is extracted from instruction manual. LOCATION OF CONTROLS Front Panel AUTO BETICAL SELECT qk (7, 12
9、) BAND qg (9, 10, 12) CHARACTER 7 (11) DIRECT qs (9) DISPLAY 5 (10, 11, 13) ENTER qa (9, 11, 12, 14) EON NEWS/INFO 3 (13, 14) EON TA 2 (13, 14) FM MODE qh (9, 10) MEMORY 4 (8, 11) MENU 0 (9, 11, 14) Numeric buttons qf (79) POWER 1 (7, 8, 12) PTY qj (14, 15) RETURN 9 (9) SHIFT qd (8, 11) TUNE MODE 8
10、(8, 10) TUNING/SELECT 6 (712, 14) 1234567890 12345786 90qaqsqdqfqgqhqjqk 1 FM ANTENNA terminal 2 AM ANTENNA terminals 3 LINE OUT jack 4 EON CONTROL OUT terminal Rear Panel ANTENNA LINE OUTEON CONTROL FM U 75 COAXIAL RLOUT AM 2134 RadioFans.CN 收音机爱 好者资料库 ST-SE570 4 This set can be disassembled in the
11、 order shown below. 2-1.DISASSEMBLY FLOW SECTION 2 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 2-2.CASE (407026) 2-2. CASE (407026) (Page 4) 2-3. MAIN BOARD (Page 5) SET 1two screws (case 3 TP2) 2two screws (case 3 TP2) 3screw (case 3 TP2) 4case (407026) ST-SE570
12、 5 2-3.MAIN BOARD 4MAIN board 2connector (CNP701) 2connector (CNP702) 2connector (CNP952) 1wire (flat type) (15 core) (CN101) 3two screws (BV/RING) 6 ST-SE570 NOTE : The preset data will be erased when this test mode is used. Therefore, take down the data before setting this mode and preset the data
13、 again after completing operations in this mode. 2. Display Tube Check and KEY Check mode 1. Turn OFF the power. 2. While pressing 1 and AUTO-BETICAL SELECT together, turn ON POWER . 3. While continuously pressing 1 and AUTO-BETICAL SELECT together, check the following. Indication test pattern The d
14、isplay changes every 1 sec. 4. Release 1 and AUTO-BETICAL SELECT . The KEY CHECK mode will be set. 5. All key numbers will be displayed. Key Number : 25 6. Each time the key is pressed, the key number will be counted down. Each key will be counted only once, at the first time. 7. When all keys have
15、been pressed, the process will end. NOTE : As contents of the Factory Preset will be written into memory after completing this check mode, delete contents of memory according to 4. Forced RESET. SECTION 3 TEST MODE 1. Circuit Check Mode Set to the reception frequency that the circuit can STEREO RDS
16、stations. (Set the input level to above 70 dB.) This enables circuit check to be performed in any of the reception modes-FM, AM (MW, LW). Set to a desired band before setting the test mode. 1. Turn OFF the power. 2. While pressing 4 and AUTO-BETICAL SELECT together, turn ON POWER . The items in the
17、following table will be checked automatically in order every 2 seconds. FM RDS DisplayItems Tuned IF Frq Sig Level Stereo RDS Signal AST signal =LOW IF COUNT OK SI LEVELh70dB ST signal=LOW RDS DATA OK DISPLAY OK or NG OK or NG OK or NG OK or NG OK or NG AM (MW, LW) OK or NG OK or NG NG IC201 NG, RV2
18、01 adjustments TB101, IC201 NG TB101 NG TB101 NG IC801 NG Microcomputer version indication (1 sec) t All light up “7F” t Dot area only “60” t Dot area only “7E” Dot area only “5F” T Dot area only “3D” T T 1 7F2 603 7E4 3D5 5F 7 ST-SE570 3. Entering the Factory Preset (In case perform just to write m
19、emory of the Factory Preset.) 1. Turn OFF the power. 2. While pressing 3 and AUTO-BETICAL SELECT together, turn ON POWER . 4. Forced RESET (Used to delete the contents of Factory Preset when it is written into the preset memory.) Clears all the RAMs and sets the initial state 1. Turn OFF the power.
20、2. While pressing 5 and AUTO-BETICAL SELECT together, turn ON POWER . 3. When “All clear” is indicated on the fluorescent display tube, it means that “Forced Reset” has been completed. 5. Language Change 1. Turn OFF the power. 2. While pressing 2, turn ON POWER . 8 ST-SE570 SECTION 4 ELECTRICAL ADJU
21、STMENTS FM Signal Level Adjustment Procedure: 1. Tune the set to 98 MHz. 2. Push the DISPLAY button for digital signal meter indication. 3. Adjust RV201 to the place where level and “70dB M” indica- tion lights on fluorescent indicator tube. Adjustment Location: MAIN BOARD Component Side FM RF signa
22、l generator set FM ANTENNA 75 coaxial (TB101) Carrier frequency : 98 MHz Modulation: 1 kHz, 40 kHz deviation Output level: 6.3 mV (76dB) (75 open) IC201 CN101 RV201 FM SIGNAL LEVEL Adjustment ST-SE570 99 SECTION 5 DIAGRAMS 5-1.NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to thi
23、s, the necessary note is printed in each block) Note on Printed Wiring Board: X : parts extracted from the component side. : Pattern from the side which enables seeing. Indication of transistor. B These are omitted. CE Q Note on Schematic Diagram: All capacitors are in F unless otherwise noted. pF:
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Sony-STSE570-tun-sm 电路图 维修手册 Sony STSE570 tun sm 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


