Sony-STRV5500-rec-sm 电路图 维修手册.pdf

《Sony-STRV5500-rec-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-STRV5500-rec-sm 电路图 维修手册.pdf（22页珍藏版）》请在收音机爱好者资料库上搜索。

1、STR-V5500 E Model Chinese Model SERVICE MANUAL FM STEREO/FM-AM RECEIVER MICROFILM STR-V5500 is RECEIVER section in MHC-V5500. SPECIFICATIONS Manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY”, “PRO LOGIC” and the double-D symbol a are trademarks of Dolby Laboratories L

2、icensing Corporation. Amplifier section Continuous RMS power output China model100+100 watts 6 ohms at 1 kHz, 10% THD (240V AC supply) 85+85 watts 6 ohms at 1 kHz, 10% THD (220V AC supply) Other models100+100 watts (6 ohms at 1 kHz,10% THD) Peak music power output 1500 watts (reference) InputsMD/VID

3、EO 1 IN (phono jacks): voltage 250 mV, impedance 47 kilo ohms AV INPUT AUDIO (phono jacks): voltage 250 mV, impedance 47 kilo ohms MIX MIc 1/2 (phone jack): sensitivity 1 mVm, impedance 10 kilo ohms OutputsMD/VIDEO OUT (phono jacks): voltage 250 mV, impedance 1 kilo ohm PHONES (stereo phone jack): a

4、ccepts headphones of 8 ohms or more. SPEAKER: accepts impedance of 6 to 16 ohms SUPER WOOFER: Voltage 1 V, impedance 1 kilo ohm Video section InputsAV INPUT VIDEO (phono jack): 1 Vp-p, 75 ohms VIDEO IN (phono jack): 1 Vp-p, 75 ohms OutputsMONITOR OUT (phono jack): 1 Vp-p, 75 ohms VIDEO OUT (phono ja

5、ck): 1 Vp-p, 75 ohms S-VIDEO (4-pin/mini- DIN jack): Y: 1 Vp-p, unbalanced, sync negative C: 0.286 Vp-p, load impedance 75 ohms Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Tuning range87.5-108.0 MHz Antenna terminals75 ohm unbalanced Intermediate frequency10.7 MHz AM tuner

6、section Tuning range Thai models:531-1,602 kHz (with the AM tuning interval set at 9 kHz) 530-1,710 kHz (with the AM tuning interval set at 10 kHz) Other models:MW 531-1,602 kHz (with the MW tuning interval set at 9 kHz) 530-1,710 kHz (with the MW tuning interval set at 10 kHz) SW 5.95-17.90 MHz (wi

7、th the SW tuning interval set at 5 kHz) Intermediate frequency450 kHz AntennaAM loop antenna External antenna terminal Design and specifications are subject to change withouto notice. RadioFans.CN 收音机爱 好者资料库 2 Notes on chip component replacement Never reuse a disconnected chip component. Notice that

8、 the minus side of a tentalum capacitor may be damaged by heat. TABLE OF CONTENTS 1.GENERAL 3 2.TEST MODE 5 3.DIAGRAMS 3-1.Circuit Boards Location 6 3-2.Printed Wiring Board Panel Section 7 3-3.Schematic Diagram Panel Section 9 3-4.Printed Wiring Board Main Section 12 3-5.Schematic Diagram Main Sect

9、ion 15 3-6.Printed Wiring Board and Schematic Diagram Power Section 19 3-7.IC Pin Function 23 3-8.IC Block Diagrams 24 4.EXPLODED VIEWS 4-1.Main Section 25 4-2.Panel Section 26 5.ELECTRICAL PARTS LIST 27 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON

10、THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. RadioFans.CN 收音机爱 好者资料库 3 SECTION 1 GENERAL FRONT PANEL 1KARAOKE PON/MPX button 2SURROUND butto

11、n 3EFFECT ON/OFF button 4MUSIC button 5MOVIE button 6GAME button 7P FILE button 8MEMO button 9DBFB button !VOLUME !GROOVE button !TUNER BAND button !STEREO/MONO button !FUNCTION button !MIC LEVEL/ECHO VOL !MIX MIC 1 jack !MIX MIC 2 jack !PHONES jack !EDIT button PLAY MODE button 1/ALL DISCS button R

12、EPEAT button HIGH FREQ button ENTER/NEXT button MULTI JOG STATION dial LOW FREQ button MEMORY button TUNING MODE button FLASH button #LOOP button #WAVE button #AV INPUT jack #CLOCK TIMER SET button #TIMER SELECT button #KEY CONTROL button #KEY CONTROL n button #DISPLAY/DEMO button #POWER button 1 2

13、3 4 5 6 7 8 9 ! ! ! ! ! ! ! ! ! !# # # # # # # # RadioFans.CN 收音机爱 好者资料库 4 BACK PANEL #ANTENNA terminal $SYSTEM CONTROL $MD/VIDEO 1 jack $FRONT SPEAKER terminal $SUPER WOOFER jack $VIDEO OUT jack $VOLTAGE SELECTOR switch # $ $ $ $ $ $ 5 FL DISPLAY/KEY LED TEST MODE Press the REPEAT, ENTER/NEXT and S

14、URROUND buttons simultaneously. 1.All FL segments and all LEDs turn on. 2.To access the microprocessor information, press the P FILE key. Each pressing of the P FILE key advances the display on the FL tube in the following sequence. 3. To check the encoder, press the MUSIC key. The following display

15、 appears on the FL tube. K0J0V0 The number after K indicates the number of times that the key is pressed. The key which was pressed in the past, is not counted. The key which is pressed hereafter is counted. Pressing any key increases the number after K. The number after J indicates the number of ro

16、tations that the JOG dial is rotated. Turning the JOG dial clockwise increases the number after J. Turning the JOG dial counter-clockwise decreases the number after J. The number after V indicates the number of rotations that the VOLUME dial is rotated. Turning the VOLUME dial clockwise increases th

17、e number after V. Turning the VOLUME dial counter- clockwise decreases the number after V. To exit this mode, perform the Cold Reset (reset clearing memory) as described below. GENERAL TEST MODE (INCLUDING AMPLIFIER AND TUNER) Press the REPEAT, ENTER/NEXT and CLOCK TIMER SET buttons simultaneously w

18、hile the main power is on. 1.Sound volume display segment starts blinking. 2.The tuning enters the PRESET mode. 3.Rotating the VOLUME control clockwise increases the volume level to maximum. Rotating the VOLUME control counter-clockwise decreases the volume level to minimum. 4.Pressing the MUSIC key

19、 decreases the equalizer curve to minimum and EQ CHECK appears on the display. Pressing the MOVIE key increases the equalizer curve to maximum. Pressing the GAME key makes the equalizer curve flat. 5.Pressing any of the DBFB, GROOVE or SURROUND key disappears EQ CHECK on the display. To exit this mo

20、de, perform the Cold Reset (reset clearing memory) as described below. SECTION 2 TEST MODE AGING MODE 1.CD aging mode To execute the CD aging, set the three discs to the CD tray and set the function to CD. REPEAT, ENTER/NEXT and LOOP buttons simultaneously. The CD aging mode starts and the disc cale

21、ndar starts blinking. 2.Tape aging mode To execute the tape aging, set the two tapes to the tape A and B drives. Set the function to TAPE. Press the REPEAT, ENTER/ NEXT and LOOP buttons simultaneously. Press the A forward key to start the tape aging mode. AGING appears on the display. CD SERVICE MOD

22、E Turn on the main power. Press the REPEAT, ENTER/NEXT and KARAOKE PON/MPX buttons simultaneously. VACS toggles between ON and OFF. VACS LEVEL DISPLAY Turn on the main power. Press the EDIT, ENTER/NEXT and KARAOKE PON/MPX buttons simultaneously. VACS level appears on the display. CD SHIP MODE Turn o

23、n the main power. Press the PLAY MODE and POWER buttons simultaneously. The main power is turned off and LOCK appears on the display. TUNER STEP CHANGE Turn on the main power. Set the function to TUNER. Select MW band from the present tuning. Turn off the main power. Press the ENTER/NEXT and POWER b

24、uttons simultaneously. The main power is turned on and the changed step appears on the display. MD/VIDEO 1 FUNCTION CHANGE Press the FUNCTION and POWER buttons simultaneously while the main power is off. When the function is set to VIDEO 1, the function is changed to MD and MD appears on the display

25、. When the function is set to MD, the function is changed to VIDEO 1 and VIDEO 1 appears on the display. COLD RESET (Reset which clears memory.) Press the REPEAT, ENTER/NEXT and DISPLAY buttons simultaneously at any time. The system is reset while clearing memory. HOT RESET (Reset which does not cle

26、ar memory.) Press the REPEAT, ENTER/NEXT and TIMER SELECT buttons simultaneously at any time. The system is reset without clearing memory. STR microprocessor version number HCD microprocessor version number VCD microprocessor version number (VCD model only) Model name Destination 3-1.CIRCUIT BOARDS

27、LOCATION SECTION 3 DIAGRAMS 6 SEC BOARD PANEL BOARD AVIN BOARD JOG BOARD VOLUME BOARD MIC ECHO BOARD AMP BOARD MAIN BOARD ENCAPSULATED COMPONENT DUMMY BOARD PRI BOARD 23 3-7.IC PIN FUNCTION IC501 TMP87CM75F-6608 (DISPLAY CONTROL) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

28、 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 to 42 43 to 46 47 48 49 50 51 to 64 65 to 98 99 100 I/O O I O O O O I I O I I O I I I I I I I I I I/O I/O O O O O O O O I I I O O O Description Not used POWER SUPPLY FOR VFT DRIVER Transfer clock output serial data Serial data input Serial data output

29、 Chip enable output Latch output to IC504 H : D542, D543 ON Stereo signal input Tuned signal input Power supply (Ground) Oscillator connection terminal (8MHz) Oscillator connection terminal (8MHz) Reset signal input terminal Oscillator connection terminal (32.768kHz) Oscillator connection terminal (

30、32.768kHz) Not used (Ground) AC Power supply off RDS DATA input (European model only) RDS clock input (European model only) SIRCS signal input JOG dial encoder input Volum encoder input Volum encoder input JOG dial encoder input Not used 12C clock I/O 12C data I/O Not used Power supply (5V) Power su

31、pply (Ground) Latch output to IC105 Latch output to IC2002 Mute output to transistorL : Mute ON DBFB level control outputL : DBFB HIGH Latch output to IC6003 H : Key con ON L : SP relay ON Not used Key data input (A/D converter) Spectrum analyzer signal input Input for model select Power supply for

32、analog (Ground) Power supply (+5V) Power supply (Ground) Grid output to FL501 Segment output to FL501 H : MUTEL : Signal Receiving Not used Pin Name NC VG COM CLK ST DATA IN COM DATA ST CE LED LAT POWER ON/OFF STEREO TUNED Vss X OUT X IN RESET XT OUT XT IN GND BACK UP RDS DATA RDS CLK SIRCS IN JOG I

33、N B VOL IN B VOL IN A JOG IN A AUB IN 12C CLK 12C DATA AUB OUT VDD Vss EQ LAT VR LAT TA MUTE VIDEO MD KEY CON LAT KEY CON ON/OFF POWER ON/OFF P LOG RELAY KEY IN 0 to 2 SPEANA 0 to 3 SUFFIX VASS VAREF VDD FL1G to 14G FLP1 to P34 ST MUTE NC 24 3-8.IC BLOCK DIAGRAMS 12345678 OVER LOAD DET F/F OFFSET DE

34、T LATCH/ AUTORESET VCC ON MUTE AC OFF DET VCC IC850PC1237HA IC105M62427FP-A IC6003 M65847FPIC6002 M65850P 12345678 ADCONT DA1CONT KEY DOWN KEY UP DAIINTIN ADINTOUT ADINTIN LPF1 REFREFREFREF HPFLPF2MIX CLKO/KEY0 SDATA/KEY1 SCK/KEY2 STROBE/KEY3 KEY4 KEY5 REF GND VCC MODE2 MODE1 DAIINTOUT LPF1IN LPF1OU

35、T HPFIN HPFOUT LPF2IN LPF2OUT MIXIN MIXOUT DA2CONT 91011121314 15 16 17 18 19 20 21 22 23 24 25 26 27 28 + LOGIC D/A RESETRAM A/D CLOCK GENERATOR REF + + + OSCILLATOR 1/2 VCC AUTO RESET LPF1 MAIN CONTROL A/D 20KBIT SRAM LPF2D/A 1234567 891014131211 CLOCK RESET MO MI D1DO0 DO1 VCC CLOCK REF OP2IN OP2

36、OUT LPF2IN LPF2OUT LPF1IN LPF1OUT OP1OUT OP1IN CC1 CC2 GND + + + + + + + SBAND GRAPHIC EQUALIZER SBAND GRAPHIC EQUALIZER U-CON INTER FACE + + + + + + + + 1234567891020191817161514131211 21222324 646362616059585756554546474849505152535444434241 25 26 27 28 29 30 31 32 33 34 40 39 38 37 36 35 80 79 78

37、 77 76 75 74 73 72 71 65 66 67 68 69 70 KEY OUT1 NC3 REC 1A REC 1B REC 1C NC4 F1 F1 F1 O1 F1 IN1 F2 F1 F2 O1 F2 IN1 F3 F1 F3 O1 F3 IN1 F4 F1 F4 O1 F4 IN1 F5 F1 F OUT1 VOL OUT1 VOL IN1 BBIN1 BB11 BB12 BBIN2 VOL OUT2 VOL IN2 F OUT2 F5 F2 F4 IN2 F4 O2 F4 F2 F3 IN2 F3 O2 F3 F2 F2 IN2 F2 O2 F2 F2 F1 IN2

38、F1 O2 F1 F2 NC6 REC 2C REC 2B REC 2A NC7 KEY OUT2 BB22 BUF IN1 BUF OUT1 NC5 AVDD DGND LATCH DATA CLOCK DVDD PORT C PORT B PORT A BUFOUT1 BUFIN1 BB21 KEY IN1 DELAY OUT DELAY IN NC2 IN 1B NC1 IN 1A AGND AVSS IN 2A NC9 IN 2B NC8 BPF IN BPF OUT KEY IN2 SECTION 4 EXPLODED VIEWS Note: -XX, -X mean standar

39、dized parts, so they may have some differences from the original one. Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The mechanical parts with no reference number in the exploded views are not supplied.

40、 Hardware (# mark) list and accessories and packing materials are given in the last of this parts list. Abbreviation MY : MalaysiaSP : Singapore HK : Hong KongIA : Indonesian CH : Chinese The components identified by mark !or dotted line with mark ! are critical for safety. Replace only with part nu

41、mber specified. 25 Ref. No.Part No.DescriptionRemarksRef. No.Part No.DescriptionRemarks 4-1.MAIN SECTION 13-363-099-11SCREW (CASE 3 TP2) * 24-991-364-11CASE * 31-666-059-11SEC BOARD * 41-666-065-11PRI BOARD * 51-666-066-11AMP BOARD 61-233-546-21ENCAPSULATED COMPONENT * 71-666-067-11DUMMY BOARD * 84-

42、991-361-01PANEL (VCD), BACK (MY,SP) * 84-991-361-11PANEL (VCD), BACK (CH) * 84-991-361-21PANEL (VCD), BACK (HK) * 84-991-361-31PANEL (VCD), BACK (IA) * 9A-4403-202-A MAIN BOARD, COMPLETE 104-970-381-11FOOT (REAR) * 113-703-244-00BUSHING (2104), CORD (IA) 113-703-571-11BUSHING (S) (4516), CORD (MY,SP

43、,HK,CH) !121-777-071-21CORD, POWER (MY,SP,HK) !121-782-315-11CORD, POWER (IA) !121-782-464-21CORD, POWER (CH) !131-569-007-11ADAPTOR, CONVERSION 2P (IA) !131-569-008-21ADAPTOR, CONVERSION 2P (MY,SP) !131-770-019-11ADAPTOR, CONVERSION PLUG 3P (HK) !T9011-431-365-11TRANSFORMER, POWER 2 1 1 3 4 11 5 7

44、10 9 8 #3 #5 not supplied not supplied not supplied #3 #4#2 T901 #2 #1 #3 #3 #3 #3 6 12 IC901 13 MY, SP, HK MODEL MY, SP MODEL 13 HK MODEL 12 13 IA MODEL 12 CH MODEL 26 4-2.PANEL SECTION Ref. No.Part No.DescriptionRemarksRef. No.Part No.DescriptionRemarks 514-991-318-01KNOB (VOL) 524-991-326-01KNOB

45、(CENTER) 534-991-317-01KNOB (JOG) 544-977-358-11CUSHION 55X-4948-895-1PANEL ASSY, FRONT 564-962-708-11EMBLEM (4-A), SONY 57X-4948-612-1DISPLAY ASSY, BUTTON * 584-932-810-11CUSHION (FL) * 594-986-870-01HOLDER, FL TUBE * 601-606-060-11AVIN BOARD * 611-666-062-11JOG BOARD 62X-4948-611-1BUTTON (E/N) ASS

46、Y 634-984-085-01SPRING (ENTER), COMPRESSION * 64A-4403-204-A PANEL BOARD, COMPLETE 654-951-620-01SCREW (2.6X8), +BVTP * 66A-4403-207-A MIC ECHO BOARD, COMPLET 674-991-327-01KNOB (CONTROL) FL5011-517-618-11INDICATOR TUBE, FLUORESCENT 58 59 61 62 60 56 53 51 55 63 65 65 65 65 65 66 64 FL501 54 57 52 6

47、7 Note: When indicating parts by reference number, please include the board name. The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No.Part No.DescriptionRemarksRef. No.Part No.DescriptionRemarks 27 COILS uH: H SEMIC

48、ONDUCTORS In each case, u: , for example: uA.: A. , uPA. , PA. , uPB. , PB. , uPC. , PC. , uPD., PD. Abbreviation MY : MalaysiaSP : Singapore HK : Hong KongIA : Indonesian CH : Chinese Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or

49、 the components used on the set. -XX, -X mean standardized parts, so they may have some difference from the original one. Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. CAPACITORS: uF: F RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable SECTION 5 ELECTRICAL PARTS LIST *1-666-066-11AMP BOARD * C8091-104-664-