Sony-STRDA2100ES-rec-sm 电路图 维修手册.pdf

《Sony-STRDA2100ES-rec-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDA2100ES-rec-sm 电路图 维修手册.pdf（94页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (Models of area code U only) With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated 110 watts per channel minimum RMS power, with no more than 0 09% total harmonic distortion from 250 milliwatts to rated

2、output Amplifier section Power output Models of area code U, CA Rated Power Output at Stereo Mode (8 ohms 20 Hz 20 kHz, THD 0 09%) 110 W + 110 W1) (8 ohms 1 kHz, THD 0 7%) 120 W + 120 W1) (8 ohms 1 kHz, THD 10%) 150 W + 150 W1) Reference Power Output1) (8 ohms 20 Hz 20 kHz, THD 0 09%) FRONT2): 110 W

3、/ch CENTER2): 110 W SURR2): 110 W/ch SURR BACK2): 110 W/ch (8 ohms 1 kHz, THD 0 7%) FRONT2): 120 W/ch CENTER2): 120 W SURR2): 120 W/ch SURR BACK2): 120 W/ch (8 ohms 1 kHz, THD 10%) FRONT2): 150 W/ch CENTER2): 150 W SURR2): 150 W/ch SURR BACK2): 150 W/ch 1) Measured under the following conditions 120

4、 V AC, 60 Hz 2) Depending on the sound field settings and the source, there may be no sound output Frequency response Inputs (Analog) 3) INPUT SHORT (with sound field and equalizer bypassed) 4) Weighted network, input level Inputs (Digital) Outputs (Analog) Outputs (Digital) Equalizer PHONORIAA equa

5、lization curve 0 5 dB MULTI CH IN, SA-CD/CD, TV/SAT, MD/TAPE, DVD, VIDEO 1, 2, 3 10 Hz 100 kHz +0 5/2 dB (with sound field and equalizer bypassed) PHONOSensitivity: 8 mV Impedance: 50 kiloohms S/N3): 86 dB (A, 8 mV4) MULTI CH IN, SA-CD/CD, TV/SAT, MD/TAPE, DVD, VIDEO 1, 2, 3 Sensitivity: 500 mV Impe

6、dance: 50 kiloohms S/N3): 96 dB (A, 500 mV4) DVD, SA-CD/CD (Coaxial) Sensitivity: Impedance: 75 ohms S/N: 100 dB (A, 20 kHz LPF) TV/SAT, SA-CD/CD, MD/TAPE, VIDEO 3 (Optical) Sensitivity: Impedance: S/N: 100 dB (A, 20 kHz LPF) MD/TAPE (OUT), VIDEO 1, 2 (AUDIO OUT) Voltage: 500 mV Impedance: 10 kilooh

7、ms SUB WOOFERVoltage: 2 V Impedance: 1 kiloohms MD/TAPE (Optical)Sensitivity: Gain levels10 dB, 0 5 dB step FM STEREO FM/AM RECEIVER US Model Canadian Model STR-DA2100ES Ver. 1.2 2006.02 SPECIFICATIONS 9-879-631-03 2006B05-1 2006.02 Sony Corporation Home Audio Division Published by Sony Techno Creat

8、e Corporation Continued on next page This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS* Digital Surround System. * Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. *“DTS”, “DTS-ES”, “Neo:

9、6” and “DTS 96/24” are trademarks of Digital Theater Systems, Inc. RadioFans.CN 收音机爱 好者资料库 2 STR-DA2100ES FM tuner section Tuning range87 5 - 108 0 MHz AntennaFM wire antenna Antenna terminals75 ohms, unbalanced Intermediate frequency10 7 MHz Sensitivity Mono:18 3 dBf, 2 2 V/75 ohms Stereo:38 3 dBf,

10、 22 5 V/75 ohms Useable sensitivity11 2 dBf, 1 V/75 ohms S/N Mono: 76 dB Stereo: 70 dB Harmonic distortion at 1 kHz Mono: 0 3% Stereo: 0 5% Separation45 dB at 1 kHz Frequency response30 Hz 15 kHz, +0 5/2 dB Selectivity60 dB at 400 kHz AM tuner section Tuning range With 10-kHz tuning scale: 530 1,710

11、 kHz5) With 9-kHz tuning scale: 531 1,710 kHz5) AntennaLoop antenna Intermediate frequency450 kHz Usable sensitivity50 dB/m (at 1,000 kHz or 999 kHz) S/N54 dB (at 50 mV/m) Harmonic distortion0 5% (50 mV/m, 400 Hz) Selectivity At 9 kHz:35 dB At 10 kHz:40 dB 5) You can change the AM tuning scale to 9

12、kHz or 10 kHz After tuning in any AM station, turn off the receiver While holding down PRESET TUNING + or TUNING +, press ?/1 All preset stations will be erased when you change the tuning scale To reset the scale to 10 kHz (or 9 kHz), repeat the procedure Video section Inputs/Outputs Video:1 Vp-p, 7

13、5 ohms S-video:Y: 1 Vp-p, 75 ohms C: 0 286 Vp-p, 75 ohms COMPONENT VIDEO:Y: 1 Vp-p, 75 ohms PB/CB/B-Y: 0 7 Vp-p, 75 ohms PR/CR/R-Y: 0 7 Vp-p, 75 ohms 80 MHz HD Pass Through General Power requirements120 V AC, 60 Hz Power consumption Power consumption (during standby mode) 0 5 W (when “INST MODE” in

14、the CIS menu is set to “OFF”) AC outlets2 switched, 120 W/1A MAX Dimensions (w/h/d) (Approx ) 430 160 5 398 5 mm (16 7/8 6 2/8 15 5/8 inches) including projecting parts and controls Mass (Approx )14 0 kg (30 lb 14 oz) Supplied accessories FM wire antenna (1) AM loop antenna (1) Remote commander RM-A

15、AE001 (1) R6 (size-AA) batteries (2) Design and specifications are subject to change without notice Area codePower consumption U310 W CA420 VA RadioFans.CN 收音机爱 好者资料库 3 STR-DA2100ES Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalu

16、m capacitor may be damaged by heat. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SON

17、T DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPE

18、AR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed meta

19、l parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any

20、one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop acros

21、s a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a

22、2 V AC range are suitable. (See Fig. A) Fig. A.Using an AC voltmeter to check AC leakage. 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground RadioFans.CN 收音机爱 好者资料库 4 STR-DA2100ES TABLE OF CONTENTS 1.SERVICING NOTES.5 2.GENERAL.6 3.DISASSEMBLY 3-1.Disassembly Flow .7 3-2.Ca

23、se .7 3-3.Front Panel Block .8 3-4.Back Panel Block .8 3-5.DIGITAL Board .9 3-6.MAIN Board.9 4.TEST MODE. 10 5.ELECTRICAL ADJUSTMENTS. 11 6.DIAGRAMS 6-1.Block Diagram DIGITAL AUDIO Section (1/2) . 12 6-2.Block Diagram DIGITAL AUDIO Section (2/2) . 13 6-3.Block Diagram ANALOG AUDIO Section . 14 6-4.B

24、lock Diagram POWER AMP Section . 15 6-5.Block Diagram VIDEO INPUT Section . 16 6-6.Block Diagram CIS, DISPLAY Section . 17 6-7.Block Diagram POWER SUPPLY Section . 18 6-8.Printed Wiring Board VIDEO (AU) Board . 20 6-9.Schematic Diagram VIDEO (AU) Board . 21 6-10. Printed Wiring Board DIGITAL Board (

25、Component Side) . 22 6-11. Printed Wiring Board DIGITAL Board (Conductor Side) . 23 6-12. Schematic Diagram DIGITAL Board (1/5) . 24 6-13. Schematic Diagram DIGITAL Board (2/5) . 25 6-14. Schematic Diagram DIGITAL Board (3/5) . 26 6-15. Schematic Diagram DIGITAL Board (4/5) . 27 6-16. Schematic Diag

26、ram DIGITAL Board (5/5) . 28 6-17. Printed Wiring Board A/V SYNC Board . 30 6-18. Schematic Diagram A/V SYNC Board . 31 6-19. Printed Wiring Board MAIN Board . 32 6-20. Schematic Diagram MAIN Board (1/3) . 33 6-21. Schematic Diagram MAIN Board (2/3) . 34 6-22. Schematic Diagram MAIN Board (3/3) . 35

27、 6-23. Printed Wiring Boards SPEAKER Section . 36 6-24. Schematic Diagram SPEAKER Section . 37 6-25. Printed Wiring Board VIDEO Board (Component Side) . 38 6-26. Printed Wiring Board VIDEO Board (Conductor Side) . 39 6-27. Schematic Diagram VIDEO Board (1/2) . 40 6-28. Schematic Diagram VIDEO Board

28、(2/2) . 41 6-29. Printed Wiring Board SVIDEO Board . 42 6-30. Schematic Diagram SVIDEO Board . 43 6-31. Printed Wiring Boards DISPLAY Section . 44 6-32. Schematic Diagram DISPLAY Section . 45 6-33. Printed Wiring Boards CIS Section . 46 6-34. Schematic Diagram CIS Section . 47 6-35. Printed Wiring B

29、oard STANDBY Board . 48 6-36. Schematic Diagram STANDBY Board . 49 7.EXPLODED VIEWS 7-1.Overall Section . 68 7-2.Front Panel Section . 69 7-3.Base Panel Section . 70 7-4.Power Transformer Section . 71 7-5.Chassis Section. 72 7-6.Back Panel Section . 73 7-7.MAIN Board Section. 74 8.ELECTRICAL PARTS L

30、IST. 75 5 STR-DA2100ES PART No. Back Panel SECTION 1 SERVICING NOTES MODEL IDENTIFICATION ModelPART No. US model2-514-880-0 Canadian model2-514-880-1 UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: So

31、me printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron ti

32、p has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more

33、viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. 6 STR-DA2100ES SECTION 2 GENERAL This sectio

34、n is extracted from instruction manual. Main unit A F D qg DIRECT q; DISPLAY 7 Display 5 INPUT MODE 8 INPUT SELECTOR qs IR (receptor) 1 MASTER VOLUME /+ 9 MEMORY/ENTER 4 MENU wf MOVIE qf MULTI CHANNEL DECODING (indicator) 6 MULTI CH IN qa MUSIC qd SPEAKERS (OFF/A/B/A+B) wh SURR BACK DECODING qj TUNI

35、NG + qk TUNING ql VIDEO 3 INPUT (jacks) wd 2CH qh ?/1 (power) 2 /+ ws ALPHABETICAL ORDER A - I MAIN MENU 3 M - O PHONES (jack) wg PRESET TUNING + w; PRESET TUNING wa P - Z NUMBERS AND SYMBOLS wdwgwhwf 289653471 qlwswa w;qk qj qh qg qf qdqsqaq; STR-DA2100ES 7 Note: Follow the disassembly procedure in

36、 the numerical order given. 3-2.CASE This set can be disassembled in the order shown below. 3-1.DISASSEMBLY FLOW SECTION 3 DISASSEMBLY 3-2. CASE (Page 7) 3-3. FRONT PANEL BLOCK (Page 8) 3-4. BACK PANEL BLOCK (Page 8) 3-5. DIGITAL BOARD (Page 9) 3-6. MAIN BOARD (Page 9) SET 1two flat head screws (TP)

37、 2two flat head screws (TP) 3two flat head screws (TP) 4two flat head screws (TP) 5case STR-DA2100ES 8 3-3.FRONT PANEL BLOCK 3-4.BACK PANEL BLOCK 7front panel block 6two connectors (CN1081, 1091) 4two screws (BVTP3 8) 2wire (flat type) (29 core) 1connector (CNS505) 3six screws (BVTP3 8) 5 2connector

38、 (CN1071) 1wire (flat type) (11 core: CNP210) 1wire (flat type) (5 core: CNS204) 2connector (CNP207) 2connector (CNP851) 6two screws (BVTP4 8) 3eleven screws (BVTP3 8) 4ten screws (BVTP3 8) 5three screws (BVTP3 8) 9back panel section 8two connectors (CNP208, 801) 1wire (flat type) (11 core) 7 STR-DA

39、2100ES 9 3-5.DIGITAL BOARD 3-6.MAIN BOARD 1wire (flat type) (29 core) (CNS505) 2two connectors (CNP507, CNP510) 7A/V SYNC board 2connector (CNP506) 8DIGITAL board 5connector (CNS551) 3two connectors (CNP811, CNP814) 4screw (BVTP3 8) 6AV SYNC holder 1connector (CNP813) 4three screws (BVTP3 8) 2screw

40、(BVTP3 8) 1two connectors (CN908, CNP802) 5two screws (BVTP3 8) 6MAIN board 3guide boards section 10 STR-DA2100ES SECTION 4 TEST MODE SOUND FIELD INITIALIZE MODE The preset sound field is cleared when this mode is activated. Use this mode before returning the product to clients upon completion of re

41、pair. Procedure: 1. While pressing the 2CH button, press theI/1button to turn on the main power. 2. The message “S. F. INITIALIZE” appears and initialization is performed. COMMAND MODE CHANGE MODE The command mode of the remote-commander which this set receives can be changed. Procedure: 1. While pr

42、essing the INPUT MODE button, press theI/1button to turn on the main power. 2. Either the message “C.MODE.AV1” or “C.MODE.AV2” appears. Select the desired mode. SF LOCK ON/OFF CHANGE MODE Procedure: 1. While pressing the MUSIC and MEMORY/ENTER buttons, press theI/1button to turn on the main power. 2

43、. Either the message “SF LOCK OFF” or “SF LOCK ON” appears. TUNER FACTORY PRESET MODE All preset contents are reset to the default setting. Procedure: 1. While pressing the MULTI CH IN and DISPLAY buttons, press theI/1button to turn on the main power. 2. The message “FACTORY PRESET” appears and the

44、present contents are reset to the default values. MEMORY CLEARING MODE All preset contents are cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair. Procedure: 1. While pressing the MUSIC and SPEAKERS buttons, press theI/1button to turn on the main power. 2. The message “MEM