Sony-TAFE370-int-sm 电路图 维修手册.pdf
《Sony-TAFE370-int-sm 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Sony-TAFE370-int-sm 电路图 维修手册.pdf(24页珍藏版)》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL INTEGRATED STEREO AMPLIFIER AEP Model UK Model SPECIFICATIONS TA-FE370/FE570 Photo: TA-FE570 Ver. 1.2 2006.02 9-873-838-13Sony Corporation 2006B05-1Home Audio Division 2006.02Published by Sony Techno Create Corporation Amplifier section DIN power output TA-FE570:110 W + 110 W (4 ohms
2、at 1 kHz) TA-FE370:70 W + 70 W (4 ohms at 1 kHz) Frequency response PHONO (20 Hz - 20 kHz):RIAA equalization curve 1.0 dB TUNER, CD, AUX, TAPE1/DAT, TAPE2/MD: 7 Hz - 70 kHz + 0 3 dB S/N (network A) PHONO:80 dB TUNER, CD, AUX, TAPE1/DAT, TAPE2/MD: 105 dB Output voltage/impedance RECOUT:200 mV, 1 kilo
3、hm PHONES:5 mW (at 8 ohms) Speakers impedance4 - 16 ohms Damping factor80 (8 ohms, 1 kHz) General System Power amplifier with all stages directly coupled Preamplifier:Low-noise, equalizer amplifier Power requirements230 V AC, 50/60 Hz Power consumption TA-FE570:190 W TA-FE370:160 W 0.6 W (In standby
4、 mode) Dimensions (approx.) (w/h/d) 430 x 135 x 310 mm incl. projecting parts and controls Mass (approx.) TA-FE570:6.5 kg TA-FE370:5.5 kg Supplied accessories Remote commander (remote) RM-S325 (1) Sony batteries R6 (size-AA) (2) Design and specifications are subject to change without notice. RadioFa
5、ns.CN 收音机爱 好者资料库 2 TA-FE370/FE570 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
6、 IN SUPPLEMENTS PUB- LISHED BY SONY. TABLE OF CONTENTS 1.SERVICING NOTES.2 2.GENERAL Location of Controls .3 3.DISASSEMBLY 3-1.Disassembly Flow .4 3-2.Case .4 3-3.Front Panel Assy .5 3-4.MAIN Board .5 4.DIAGRAMS 4-1.Note for Printed Wiring Boards and Schematic Diagrams .7 4-2.Printed Wiring Board MA
7、IN Board .8 4-3.Schematic Diagram MAIN Board .9 4-4.Printed Wiring Boards CONTROL/SPEAKER SW/ VOLUME/Boards . 10 4-5.Schematic Diagram CONTROL/SPEAKER SW/ VOLUME Boards . 11 4-6.Printed Wiring Boards AC OUTLET/HEADPHONE/LOUDNESS/ POWER SW/STANDBY Boards . 12 4-7.Schematic Diagram AC OUTLET/HEADPHONE
8、/LOUDNESS/ POWER SW/STANDBY Boards . 13 4-8.IC Pin Function Description . 14 5.EXPLODED VIEWS 5-1.Case Section . 15 5-2.Front Panel Section . 16 5-3.Chassis Section . 17 6.ELECTRICAL PARTS LIST. 18 SECTION 1 SERVICING NOTES INRECOUTIN PHONO IN TUNER ININRECOUTIN CDAUXTAPE2/MDTAPE1/DAT EON CONTROL AC
9、 OUTLET SPEAKERS L R IMPEDANCE USE 4 - 16 SWITCHED 100W MAX + + RL SIGNAL GNDU IN PART No. ModelPART No. TA-FE570: AEP model4-233-359-0 TA-FE570: UK model4-233-359-1 TA-FE370: AEP model4-233-359-2 TA-FE370: UK model4-233-359-3 MAIN BOARD SETTING On AEP model of this set, AC outlet is mounted onto th
10、e AC OUT- LET board holding the back panel between. Since removing the MAIN board alone is difficult, in repairing the MAIN board, handle the MAIN board with the back panel connected as shown in the figure below. back panel MAIN board MODEL IDENTIFICATION Back Panel Ver 1.1 2001.07 UNLEADED SOLDER B
11、oards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics
12、. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C . Caution: The printed p
13、attern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is be
14、st to use only unleaded solder but unleaded solder may also be added to ordinary solder. RadioFans.CN 收音机爱 好者资料库 3 TA-FE370/FE570 SECTION 2 GENERAL This section is extracted from instruction manual. 2541 3 qa0 9876qfqdqs BALANCE 8 (8) BASS 0 (8) EON LINK (TA-FE570 only) qd (8) INPUT SELECTOR 4 (8, 9
15、) LOUDNESS 6 (8) PHONES jack qf (8) SOURCE DIRECT 7 (8) SPEAKERS selector qa (8) STANDBY indicator 1 TAPE1 MONITOR (TA-FE570 only) qs (9) TREBLE 9 (8) VOLUME control 5 (8) ?/1 (power) 2 (8, 9) (remote control sensor) 3 (5) INRECOUTIN PHONO IN TUNER ININRECOUTIN CDAUXTAPE2/MDTAPE1/DAT EON CONTROL AC
16、OUTLET SPEAKERS L R IMPEDANCE USE 4 - 16 SWITCHED 100W MAX + + RL SIGNAL GNDU IN 1 3 5 268974 1 PHONO jack 2 TUNER jack 3 CD jack 4 AUX jack 5 TAPE2/MD jack 6 TAPE1/DAT jack 7 SPEAKERS terminal 8 EON CONTROL connector (FE570) 9 AC OUTLET connector (AEP model) LOCATION OF CONTROLS Front Panel Back Pa
17、nel RadioFans.CN 收音机爱 好者资料库 TA-FE370/FE570 4 This set can be disassembled in the order shown below. 3-1.DISASSEMBLY FLOW SECTION 3 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 3-2.CASE 3-2. CASE (Page 4) 3-3. FRONT PANEL ASSY (Page 5) 3-4. MAIN BOARD (Page 5) SET
18、1two screws (case 3 TP2) 1two screws (case 3 TP2) 1two screws (case 3 TP2) 2 2 3case TA-FE370/FE570 5 3-3.FRONT PANEL ASSY 3-4.MAIN BOARD 5two screws (BVTP3 8) 6four screws (BVTP3 8) 3screw (BVTP3 8) 1connector (CN811) 4harness 1connector (CN812) 2wire (flat type) (15 core) (CN815) 7front panel assy
19、 3two screws (BVTP3 8) 4two screws (BVTP3 8) 3screw (BVTP3 8) 3three screws (BVTP3 8) 5MAIN board 2connector (CN901) 1connector (CN902) TA-FE370/FE570 6 MEMO TA-FE370/FE570 77 SECTION 4 DIAGRAMS 4-1.NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Board: X : parts extract
20、ed from the component side. : Pattern from the side which enables seeing. (The other layers patterns are not indicated.) Indication of transistor B These are omitted. CE Q B These are omitted. CE Q Note on Schematic Diagram: All capacitors are in F unless otherwise noted. pF: F 50 WV or less are not
21、 indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. f: internal component. 2 : nonflammable resistor. C : panel designation. A : B+ Line. B : B Line. Voltages and waveforms are dc with respect to ground under no-signal conditions. no
22、mark : TUNER Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal produc- tion tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal produc- tion tolerances. Circled numbers refer to waveforms. Signal path. F
23、: TUNER E: TAPE1/DAT IN a: RECOUT d: TAPE2/MD IN J: CD I : PHONO Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Waveform CONTROL Board 1 IC801 1 (XOUT) Circuit Boards Location POWER SW board STANDBY board AC OUTL
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Sony-TAFE370-int-sm 电路图 维修手册 Sony TAFE370 int sm 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


