Onkyo-TXSR8260-avr-sm 电路图 维修手册.pdf
《Onkyo-TXSR8260-avr-sm 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Onkyo-TXSR8260-avr-sm 电路图 维修手册.pdf(115页珍藏版)》请在收音机爱好者资料库上搜索。
1、RC-590M or RC-591M TX-SR602 TX-SR602/E SERVICE MANUALSERVICE MANUAL Ref. No. 3825 092004 120V AC, 60Hz 230-240V AC, 50Hz 120/220-230V AC, 50/60Hz 220-230V AC, 50Hz AV RECEIVER MODEL TX-SR602/E/8260 Black, Golden and Silver models BMDD,BMDC,SMDC BMPP,SMPP,BMPA,SMPA,GMPT BMWT,GMWT GMGK,GMGQ,GMGR SAFET
2、Y-RELATED COMPONENT WARNING! THE MARK FOUND ON SOME COMPONENT PARTS INDICATES THE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. WHEN REPLACING, BE SURE TO USE PARTS OF IDENTICAL DESIGNATION. MAKE LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM
3、 THE SUPPLY CIRCUIT BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. RadioFans.CN 收音机爱 好者资料库 TX-SR602/E SPECIFICATIONS Amplifier Section Video Section Tuner Section FM AM General Video Inputs Video Outputs Audio Inputs Audio Outputs Other Jacks Specifications and features are subject to change withou
4、t notice. Power Output 2 channel driven: American 85 W + 85 W (8 ,20Hz 20kHz,FTC) European: 120 W + 120 W (6 ohm ,1kHz,DIN) Asian: 150 W + 150 W (6 ohm ,1kHz,JEITA) Dynamic Power220 W + 220 W (3 ohm ,Front) 165 W + 165 W (4 ohm ,Front) 100 W + 100 W (8 ohm ,Front) THD (Total Harmonic Distortion)0.08
5、 % (Power Rated) Damping Factor60 (Front,1kHz,8 ohm) Input Sensitivity and Impedance200 mV/ 47 kohm (LINE) Output Level and Impeadance200 mV/ 470 ohm (REC OUT) Frequency Response10 Hz100 kHz/ +1 dB-3 dB (Direct mode) Tone Control10 dB, 50 Hz (BASS) 10 dB, 10 kHz (TREBLE) SN Ratio106 dB (LINEIHF-A) S
6、peaker ImpedanceAmerican : 6 ohm other :4 ohm Input Sensitivity/Output Level and Impedance1 Vp-p /75 ohm (Component and S-Video Y) 0.7 Vp-p /75 ohm ohm (Component Pb/Cb,Pr/Cr) 0.28 Vp-p /75 ohm (S-Video C) 1 Vp-p /75 ohm (Composite) Component Video Frequency Response5 Hz 50 MHz Tuning Frequency Rang
7、eAmerican: 87.5 MHz107.9 MHz Others : 87.5 MHz108.0 MHz Usable SensitivityStereo; 17.2 dBf 2 V(75 ohm IHF) Mono; 11.2 dBf 1 V(75 ohm IHF) S/N RatioStereo; 70 dB (IHF-A) Mono; 76 dB (IHF-A) THDStereo; 0.3 % (1kHz) Mono 0.2 % (1kHz) Frequency Response30 Hz15 kHz / 1 dB Stereo Separation45 dB ( 1kHz )
8、Tuning Frequency RangeAmerican: 530 kHz1700 kHz Others: 522 kHz1611 kHz Usable Sensitivity30 V S/N Ratio40 dB THD0.70% Power SupplyAmerican: AC 120 V, 60 Hz Australian and European: AC 230-240 V, 50 Hz Others : AC 120/220-230 V, 50/60 Hz AC 230-240 V, 50Hz AC 220-230 V, 50/60 Hz Power ComsumptionAme
9、rican : 8.1A Others : 700 W Standby Power Comsumption1.0 W Dimensions(W x H x D) 435 W x 175 H x 430 D mm 17-1/8 W x 6-7/8 H x 16-15/16 D inches WeightAmerican, Australian, European, Singapore and East southern asian:13.6 kg 30.0 lbs Others:14.8 kg 32.6 lbs Component Video Input 1,2,3 S-Video Compat
10、ible Jack InputDVD,VIDEO1,VIDEO2,VIDEO3, VIDEO4 A/V InputDVD,VIDEO1,VIDEO2,VIDEO3, VIDEO4 Component Video OutputOUT S-Video Compatible Jack OutputMONITOR OUT,VIDEO1,VIDEO2 A/V OutputMONITOR OUT,VIDEO1,VIDEO2 Digital InputsOptical : 4(American) 3(Others) Coaxial : 2 Analog InputsDVD(MULTICHANNEL),VID
11、EO1,VID EO2,VIDEO3,VIDEO4,TAPE,CD Multichannel Inputs6 Digital OutputsOptical : 1 Analog OutputsTAPE,VIDEO1,VIDEO2 Subwoofer Pre Outputs 1 Speaker Outputs9 Phones1 IR Input1 12V Trigger Out1 RadioFans.CN 收音机爱 好者资料库 2. To initialize the unit This device employs a microprocessor to perform various fun
12、ctions and operations. If interference generated by an external power supply, radio wave, or other electrical source results in accident which causes the specified operations and functions to operate abnormally. To perform a result, please follow the procedure below. 1.Press and hold down the VIDEO-
13、1 button, then press the STANDBY/ON button. 2.After CLEAR is displayed, the preset memory and each mode stored in the memory, such as surround, are initialized and will return to the factory setting. 3. Unplug the power supply cord. 3. Safety-check out (U.S.A. model only) After correcting the origin
14、al service problem, perform the following safety check before releasing the set to the customer. Leakage Current Check Measure leakage current to a known earth ground(water pipe, conduit, etc.) by connecting a leakage current tester between the earth ground and exposed metal parts of the appliance (
15、input/output terminals, screwheads,metal overlays, etc.). Plug the power supply cord directly into a 120V AC 60 Hz outlet and turn Standby switch on. Any current meausred must not exceed 0.5mA. 1. Replacing the fuses This symbol located near the fuses indicates that the fuse used is fast operating t
16、ype. For continued protection against fire hazard, replace with same type fuse. For fuse rating refer to the marking adjacent to the symbol. Ce symbole indique que le fusible utlise est a rapide. Pour une protection permanente, nuntiliser que fusibles de meme type. Ce darnier est la qu le present sy
17、mbol est appse. 4.Setting the voltage selector (Worldwide models only) Worldwide models are equipped with a voltage selector to conform with local power supplies. Be sure to set this switch to match the voltage of the power supply in your area before plugging in the unit. Determine the proper voltag
18、e for your area: 220-230 V or 120 V. If the preset voltage is not correct for your area, insert a screwdriver into the groove in the switch. Slide the switch all the way to the upper (120 V) or to the lower (220-230 V), whichever is appropriate. 5.Setting the AM tuning step frequency (Worldwide mode
19、ls only) CIRCUIT NO. PART NO. DESCRIPTION Note: :120V model only : Other models except 120V model : Asian model only for 230V 120 V VOLTAGE SELECTOR 220-230 V 1 Press the RECEIVER button fol- lowed by the SETUP button. The main menu appears onscreen. 2 Use the Up and Down / buttons to select 1. init
20、ial Setup, and then press ENTER. The Initial Setup menu appears. 3 Use the Up and Down / buttons to select 3. Hardware Setup, and then press ENTER. The Hardware Setup menu appears. 4 Use the Up and Down / buttons to select d. AM Fre- quency Step, and then use the Left and Right / buttons to select:
21、10 kHz: Select if 10 kHz steps are used in your area. 9 kHz: Select if 9 kHz steps are used in your area. 5 Press the SETUP button. The setup menu closes. RECEIVER ENTER ENTER Menu - 1.Initial Setup 2.Speaker Setup Advanced Setup 3.Surround Setup 4.Audio Adjust 5.Listening Mode Preset 6.Preference B
22、asic Setup 1.Initial Setup - 2.Component Video 3.Hardware Setup 1.Digital Input 1-3.Hardware Setup - :Not Activated b.Sp Impedance Minimum :6ohms c.TV Format :NTSC d.AM Frequency Step : 9kHz a.Powered Zone2 ENTER F6901,F6902 252301 or12A-TUL-250V or 25219612A-UL/T-314,Fuse F901 25219910A-UL,Fuse F90
23、2 252078,5A-SE-EAK, 252244 or5A-SE-TL250V or 2522785A-SE-TL250V,Fuse F903 252164 or5A-UL/T-237 or 2522585A-T/UL-ST2,Fuse 252075,2.5A-SE-EAK, 252241 or2.5A-SE-TL250V or 2522752.5A-SE-TL250V,Fuse F9501 252160 or2.5A-UL/T-237 or 2522542.5A-T/UL-ST2,Fuse 252075,2.5A-SE-EAK, 252241 or2.5A-SE-TL250V or 25
24、22752.5A-SE-TL250V,Fuse TX-SR602/E SERVICE PROCEDURES RadioFans.CN 收音机爱 好者资料库 A038 A039 A187 A186 A031 A059 A031 A046 A091 A031 A031 A036 A031 U33 A031 A031 A042 A033 A037 A031 A211 A031 A101 Q6050 Q6055 Q6064 Q6066 A031 Q6050A A151 A031 A031 A031 A031 T901 A070 A196 A057 E800 A056 A041 A018 A011 A0
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Onkyo-TXSR8260-avr-sm 电路图 维修手册 Onkyo TXSR8260 avr sm 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


