Sony-TAF501ES-int-sm 电路图 维修手册.pdf

《Sony-TAF501ES-int-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-TAF501ES-int-sm 电路图 维修手册.pdf（68页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL INTEGRATED STEREO AMPLIFIER AEP Model UK Model TA-F501ES Ver. 1.0 2007.04 SPECIFICATIONS 9-887-686-01 2007D04-1 2007.04 Sony Corporation Home Audio Division Published by Sony Techno Create Corporation Continued on next page This amplifier incorporates Dolby* Digital and DTS*. *Manufac

2、tured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. * “DTS” and “DTS 2.0” are trademarks of DTS, Inc. Amplifier section POWER OUTPUT Rated Power Output* 6 ohms 1 kHz, THD 0.7%: 65 W + 65 W Power requirements 230 V AC, 50/60 Hz * Measured

3、 under the following conditions: Power requirements: 230 V AC, 50/60 Hz Frequency response Inputs (Analog) PHONORIAA equalization curve 0.5 dB TUNER, SA-CD/CD, TAPE 10 Hz 40 kHz 3 dB (8 ohms) PHONOSensitivity: 2.5 mV Impedance: 50 kohms S/N: 86 dB (A, 20 kHz LPF) Output (Analog) Inputs (Digital) TUN

4、ER, SA-CD/CD, TAPE Sensitivity: 150 mV Impedance: 50 kohms S/N: 96 dB (A, 20 kHz LPF) TAPEVoltage: 150 mV Impedance: 1 kohms DIGITAL 1/2/3Impedance: 75 ohms S/N: 96 dB (A, 20 kHz LPF) DIGITAL 4S/N: 96 dB (A, 20 kHz LPF) RadioFans.CN 收音机爱 好者资料库 2 TA-F501ES SAFETY-RELATED COMPONENT WARNING! COMPONENTS

5、 IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. Notes on chip component replacement Never r

6、euse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come

7、printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint

8、 for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) t

9、han ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. 60 W Output (Digital) TONE General Power requirements 230 V AC, 50/60 Hz ower consu

10、mption including projecting parts and controls Mass Supplied accessories Operating Instructions Optimizer microphone ECM-AC1 (1) AC power cord (mains lead) (1) Remote commander RM-AAU012 (1) Design and specifications are subject to change without notice. DIGITAL 4S/N: 96 dB (A, 20 kHz LPF) TREBLE10

11、dB, 1 dB step BASS10 dB, 1 dB step P Dimensions (w/h/d) (Approx.) 280 111 286 mm (Approx.) 4.6 kg RadioFans.CN 收音机爱 好者资料库 3 TA-F501ES TABLE OF CONTENTS 1.SERVICING NOTES.4 2.GENERAL.7 3.DISASSEMBLY 3-1.Top Plate, Side Plate.9 3-2.Power Board . 10 3-3.Front Panel Assy. 10 3-4.Main Board. 11 4.TEST MO

12、DE. 12 5.DIAGRAMS 5-1.Block Diagram Input Section . 15 5-2.Block Diagram DSP Section . 16 5-3.Block Diagram AMP Section . 17 5-4.Block Diagram Power Supply Section . 18 5-5.Printed Wiring Board Main Board (Component Side) . 20 5-6.Printed Wiring Board Main Board (Conductor Side) . 21 5-7.Schematic D

13、iagram Main Board (1/5) . 22 5-8.Schematic Diagram Main Board (2/5) . 23 5-9.Schematic Diagram Main Board (3/5) . 24 5-10. Schematic Diagram Main Board (4/5) . 25 5-11. Schematic Diagram Main Board (5/5) . 26 5-12. Printed Wiring Board DSP Board . 27 5-13. Schematic Diagram DSP Board . 28 5-14. Prin

14、ted Wiring Board MIC Board . 29 5-15. Schematic Diagram MIC Board . 30 5-16. Printed Wiring Boards Panel Section . 31 5-17. Schematic Diagram Panel Section . 32 5-18. Schematic Diagram Power Supply Section . 33 5-19. Printed Wiring Board Power Supply Section (1/2) . 34 5-20. Printed Wiring Boards Po

15、wer Supply Section (2/2) . 35 6.EXPLODED VIEWS 6-1.Plate Section . 50 6-2.Power Board Section . 51 6-3.Front Panel Section . 52 6-4.Chassis Section. 53 7.ELECTRICAL PARTS LIST. 54 RadioFans.CN 收音机爱 好者资料库 4 TA-F501ES ERROR MESSAGES If there is a malfunction, the display shows a code of two numbers. Y

16、ou can check the condition of the system by message. Refer to the following table to solve the problem. If any problem persists, consult your nearest Sony dealer. MessagesCheck codeCause and Response PROTECTOR11Irregular current is output from the speakers. Turn off the ampli- fier, check the centra

17、l core of a speaker cord is not touching the amplifier or other speakers, and turn on again. PROTECTOR12The amplifier section is overheated. Check that the ventilation hole is not covered. Turn off the amplifier, leave the amplifier for a while, and turn on the power again. PROTECTOR14Turn off the a

18、mplifier, check the central core of a speaker cord is not touching the amplifier or other speakers. PROTECTOR21Turn off the amplifier and check that the speaker cords are connected correctly, then turn the power on again. SECTION 1 SERVICING NOTES POWER BOARD SERVICE POSITION POWER board insulate pl

19、ate To check the backside, remove the AC inlet from the back panel. 5 TA-F501ES MAIN BOARD SERVICE POSITION No need of connection to the HP board. PANEL board MAIN board POWER board AC 2P inlet SW board POWER board AC 2P inlet SW board MAIN board PANEL board 6 TA-F501ES DISCHARGING THE CAPACITORS R4

20、5 R46 R57 D23 C4 C24 C62 C100 D24 C63 C2TH1 R2 L6 EP1 D27 D1 FR1 CN11 1234 (CHASSIS) In order to prevent electric shock when checking the board, connect between the terminals of the capacitor (C100) with the specified resistor to discharge the capacitor (C100). 800/2W In order to prevent electric sh

21、ock when checking the board, connect between the terminals of the connector (CNP5301) with the specified resistor to discharge the capacitors (C1532 and C1548). 800/2W CNP5301 MAIN board C1532 C1548 7 TA-F501ES SECTION 2 GENERAL This section is extracted from instruction manual. Front panel Location

22、 of Parts and Operation NameFunction APOWERPress to turn the amplifier on or off. BRemote sensor Receives signals from the remote. CTONE BASS/TREBLE Turn to adjust the BASS and TREBLE levels. The level can be adjusted from 10 dB to +10 dB. DDisplayThe current status of the selected component or a li

23、st of selectable items appears here. NameFunction G MUTINGPress to turn off the sound temporarily. Press the button again to restore the sound. H PHONES jackConnects to headphones. EINPUT SELECTOR Turn to select the input source to play back. FVOLUMETurn to adjust the volume level of speakers. The l

24、evel can be adjusted from dB to +23 dB. Location of Parts and Operation Rear panel AAUDIO INPUT/OUTPUT section Audio input/ output jacks Connects to a Super Audio CD player, tape deck, MD deck or DAT player, etc (page 6). BAUTO CAL MIC jack Connects to the supplied optimizer microphone for the Auto

25、Calibration function (page 13). ESIGNAL GND terminal If a turntable has a ground (earth) wire, connect it to this terminal to avoid a hamming noise (page 6). CDIGITAL INPUT/OUTPUT section COAXIAL IN jacks Connects to a DVD player, Super Audio CD player, etc. The COAXIAL jacks provide a better qualit

26、y sound (page 7). OPTICAL IN/ OUT jack DSPEAKERS section Connects to speakers (page 5). 8 TA-F501ES Remote commander RM-AAU012 Notes The remote command mode of the remote supplied with this amplifier is fixed to CD1 for the connected CD player. Set the remote command mode of the CD player to CD1; ot

27、herwise, you cannot operate the CD player using this remote. You can adjust the BASS and TREBLE levels manually even when the LOUDNESS function is set to ON. If you adjust the levels manually, the LOUDNESS function will be switched to OFF, automatically. NameFunction A DISPLAY ON/OFF Press to turn t

28、he display in the display window on and off. B Input buttons Press one of the buttons to select the component you want to use. C VOL +/Press to adjust the volume level of speakers. The level can be adjusted from dB to +23 dB. D BALANCE L/R Press to adjust the balance between left and right speakers.

29、 Both the left and the right balance can be adjusted from 0 dB to +20 dB. The initial setting is 0 dB (center). E Operation buttons for a Sony CD player You can only operate a Sony CD player using this remote, when you connect it to the this amplifier. H playback X pause x stop ./ select a track m/M

30、 fast backward/ forward F MUTINGPress to turn off the sound temporarily. Press the button again to restore the sound. G MENUPress to display the menu for the amplifier (page 16). H V/v/B/b After pressing MENU (7), press V/v/B/b to select the settings. Then press to enter the selection (page 16). I L

31、OUDNESSSet the LOUDNESS function to ON to adjust the BASS and TREBLE levels output from the speakers to the optimum settings, based on the volume level. When you set the LOUDNESS function to OFF, the BASS and TREBLE levels will return to the levels that had been adjusted before the LOUDNESS function

32、 was set to ON. Initial setting is OFF. J BASS/ TREBLE +/ Press to adjust the BASS and TREBLE levels. The level can be adjusted from 10 dB to +10 dB. NameFunction 9 TA-F501ES Note: Follow the disassembly procedure in the numerical order given. 3-1.TOP PLATE, SIDE PLATE This set can be disassembled i

33、n the order shown below. SECTION 3 DISASSEMBLY 3-1.TOP PLATE, SIDE PLATE (Page 9) SET 3-2.POWER BOARD (Page 10) 3-3.FRONT PANEL ASSY (Page 10) 3-4.MAIN BOARD (Page 11) 1 two flat head screws (TP) 2 two flat head screws (TP) 8 two flat head screws (TP) 7 two flat head screws (TP) 4 two flat head scre

34、ws (TP) 5 two flat head screws (TP) 3 top plate 6 side plate (L) 9 side plate (R) 10 TA-F501ES 3-2.POWER BOARD 3-3.FRONT PANEL ASSY qa three screws (+BVTP 3 8) qd three screws (+BVTP 3 8) qs screw (+BVTT 3 6) 8 two screws (+BVTP 3 8) 9 two screws (+BVTP 3 8) 0 bracket (power MT) 1 CN11 (4P) 2 CN1 (2

35、P) 4 CNP95 (3P) 6 CNP98 (3P) 7 CNP97 (6P) 3 CNP96 (2P) 5 CNP99 (5P) qf POWER board 4 two screws (+BVTP 3 8) 5 three screws (+BVTP 3 8) 6 front panel assy 1 CNP2001 (6P) 2 CNP2011 (13P) 3 CNP1401 (15P) 11 TA-F501ES 3-4.MAIN BOARD 2 two screws (+BVTT 3 6) 8 two screws (+BVTP 2.6 (3CR) 9 two screws (+B

36、VTP 2.6 (3CR) 0 DSP board qa MAIN board 4 five screws (+BVTT 3 5) 7 5 two screws (+BVTP 3 8) 6 five screws (+BVTP 3 8) 3 heat sink assy 1 CN1005 (5P) 12 TA-F501ES Items Protector on/off Model version display Model/destination change FM/AM tuner version display HDMI controller version display HDMI co

37、ntroller update mode Speaker output setting FL display fonts test FL display test Audio swap mode DSP halt DSP Version display Volume value display (FL/FR) Volume value display (SL/SR) Volume value display (CT/SW) Display PROTECTOR ON/OFF XXX # * vX. XX MODEL # * * * * X X FM/AM Tuner Ver X. XX HDMI

38、 Micom Ver X. XX HDMIUcom Update XXX SPEAKER OUT XXXXX FL FONT 0 x* = X ALL ON SWAP XXXXXXXXXXX DSP HALT XXX DSP Ver S: *, P: XXX FL* FR XXXX SL* SR XXXX CT* SW XXXX Remark “ON”: Power supply will cut in 5 seconds when the protector works. “OFF”: Power supply doesnt cut when the protector works. Not

39、e:It is not possible to set it to ON until turning off power when the protector setting is set to OFF. Turn on the power supply again when setting it to ON. XXX: ON or OFF (It switches by pressing the U u key of the remote commander after the item is fixed pressing the ENTER key of the remote comman

40、der) #: model *: destination X.XX: main system controller software version : Sum value of flash memory in the main system controller Not used Not used Not used Not used XXXXX: Selection of speaker output audio SOURCE: nomally mode, MIC: mode that output audio from mic from speaker (It switches by pr

41、essing the U u key of the remote commander after the item is fixed pressing the ENTER key of the remote commander) All the fonts to be displayed on the FL display can be checked. *: hexadecimal character code. (It switches by pressing the U u key of the remote commander after the item is fixed press

42、ing the ENTER key of the remote commander.) X: character corresponding to the specified code. All segment is display Not used XXX: ON or OFF (It switches by pressing the U u key of the remote commander after the item is fixed pressing the ENTER key of the remote commander) Mode not to send DSP host

43、code, and to make only decipherment done *: DSP decoder patch version XXX: DSP post process version *: Front L-ch volume value XXXX: Front R-ch volume value Not used Not used SECTION 4 TEST MODE MEMORY CLEARING MODE All preset contents are cleared when this mode is activated. Use this mode before re

44、turning the product to clients upon completion of repair. Procedure: 1. While pressing the MUTING button, press the POWER button to turn on the main power. 2. The message “MEMORY CLEARING.” appears and the memories are reset to the default values. 3. When done, the message “MEMORY CLEARED !” appears

45、. SPECIAL MENU MODE Procedure: 1. Press the POWER button to turn on the main power and press the MUTING button for more than 5 seconds. 2. The message “MENU SPECIALIZED!” appears. 3. When U u key of the remote commander is pressed, the message “SPECIAL” appers. 4. The item of special menu mode is selected pressing U u key of the remote commander after ENTER key of the remote commander is pressed. 5. To release from this mode, press the MUTING button for more than 5 secon