Onkyo-A9050-int-sm 电路图 维修手册.pdf
《Onkyo-A9050-int-sm 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Onkyo-A9050-int-sm 电路图 维修手册.pdf(102页珍藏版)》请在收音机爱好者资料库上搜索。
1、A-9050 RC-830S Integrated Amplifier Black and Silver models MODEL A-9050(B)/(S) 120V AC, 60Hz 230V AC, 50Hz 230V AC, 50Hz B MDC B MPP S MPP Ref. No. 4412 092012 RadioFans.CN 收音机爱 好者资料库 A-9030 / 9050 / M-5010 / ADM-20.4 Service Procedure 1. Setting for shipping 1-1. Initialization of memories A-9050,
2、 A-9030 Push PURE DIRECT button and Standby at same time. 1-2. Initial setting A-9050, A-9030 SELECTOR SPEAKERS BASS TREBLE BALANCE VOLUME PURE DIRECT RI MODE 4ohm/8ohm Auto Standby M-5010, ADM-20.4 Input Level 12Vtrg or Audio 4ohm/8ohm Auto Standby RadioFans.CN 收音机爱 好者资料库 A-9030/9050/M-5010/ADM-20.
3、4 Operation Check - 1 1-1. Confirm Relay operation a. Confirm that the relay of SP A and the relay of SP B operate normally respectively by SPEAKER A/B TRIM. b. It is confirmed that the relay cuts at once if becoming POWER OFF. c. Confirm no-sound from SWpreOUT when you insert HP JACK. (A-9050 / A-9
4、030 ONLY) d. Confirm relay operation, when 4ohm-8ohm switch is change to the other possition. 1-2. Confirm of remote controll operations.(A-9050, A-9030 ONLY) a. Confirm that specified operations for each button are made. b. Confirm the RI operation. c. Confirm the change of RI mode to swith S7901-S
5、7903 (A-9050 ONLY) 1-3. Confirm of Audio Sense operations.(M-5010, ADM-20.4 ONLY) a. TRIGGER switch is AUDIO at the condition of no input, and it turns off power. b. Confirm that it dosent become the POWER ON ,if -65dBV, 1KHz inputs. c. Confirm that it becomes the POWER ON ,if -45dBV, 1KHz inputs. 1
6、-4. Confirm of 12V trigger operations.(M-5010, ADM-20.4 ONLY) a. TRIGGER switch is 12Vtrg at the condition of no input, and it turns off power. Confirm it become the POWER ON if 12V trigger is input. b. Confirm 12VTRG is output when the POWER ON. RadioFans.CN 收音机爱 好者资料库 A-9030/9050/M-5010/ADM-20.4 O
7、peration Check - 2 2-1. Voltage protection a. The unit receives the remote control signal, it goes into the test mode 1-02. b. The speaker relay become OFF immediately after D.C. 1.5V inputs to CD SELECTOR to check L and R. The same as above when D.C. -1.5V inputs at each place. NOTE 1: Limit time t
8、o apply voltage is 0.5-1.0 seconds each channel. When protection operation does not occur at once, try several times. NOTE 2: Dont connect load nor short speaker terminals. * When you check this protection, you must use the test mode 1-02. 2-2. Current protection a. The unit receives the remote cont
9、rol signal, it goes into the test mode 1-02. b. The relay shall be ON when 2 ohm load is connected to each channel under the conditions of Peak-to-zero 20V output for L,R channels and no load by using the INTEGRA amplifier series Designated circuit with 50Hz square wave. c. The relay shall be OFF wh
10、en 0.5 ohm load is connected to each channel under the conditions of Peak-to-zero 20V output for L,R channels and no load by using the INTEGRA amplifier series Designated circuit with 50Hz square wave. * When you check this protection, you must use the test mode 1-02. A-9030/9050/M-5010/ADM-20.4 Ope
11、ration Check - 3 TESTFunctionAnalog InputSpeakerVolumeBalanceBassTrebleDirectPMBassAMUTEETC No 1-00All LED light up.LINE1SPEAKER A0dBCENTER0dB0dBONOFFOFF*1 1-01Thermal test mode.LINE1SPEAKER A0dBCENTER0dB0dBONOFFOFF*2 1-02Protect test mode.LINE1SPEAKER A0dBCENTER0dB0dBONOFFOFF*3 1-03Idling timer mod
12、e.LINE1SPEAKER A0dBCENTER0dB0dBONOFFOFF*4 2-00Direct Volume Max.LINE1SPEAKER AMAXCENTER0dB0dBONOFFOFF 2-01Direct Volume Min.LINE1SPEAKER AMINCENTER0dB0dBONOFFOFF 2-02Tone Volume Max.LINE1SPEAKER AMAXCENTER0dB0dBOFFOFFOFF 2-03Tone Balance Rmax.LINE1SPEAKER AMAXRMAX0dB0dBOFFOFFOFF 2-04Tone Balance Lma
13、x.LINE1SPEAKER AMAXLMAX0dB0dBOFFOFFOFF 2-05Tone Bass Max.LINE1SPEAKER AMAXCENTERMAX0dBOFFOFFOFF 2-06Tone Bass Min.LINE1SPEAKER AMAXCENTERMIN0dBOFFOFFOFF 2-07Tone Treble Max.LINE1SPEAKER AMAXCENTER0dBMAXOFFOFFOFF 2-08Tone Treble Min.LINE1SPEAKER AMAXCENTER0dBMINOFFOFFOFF 2-09Tone PMBass ON.LINE1SPEAK
14、ER AMAXCENTER0dB0dBOFFONOFF 2-10Amute ON.LINE1SPEAKER AMAXCENTER0dB0dBONOFFON 2-11Volume -40dB.PHONOSPEAKER A-40dBCENTER0dB0dBONOFFOFF 2-12Phono Volume Max.PHONOSPEAKER AMAXCENTER0dB0dBONOFFOFF 2-13Phono Volume Min.PHONOSPEAKER AMINCENTER0dB0dBONOFFOFF 3-00Digital3 Input Test.D3SPEAKER AMINCENTER0dB
15、0dBONOFFOFF A-9050 Exploded Views - 1 A 1 2 3 4 5 BCD 838430088GR Screws: 3TTB+8B(3BC) A230 COVER REFER TO EXPLODED VIEWS - 2 REFER TO EXPLODED VIEWS - 3 A-9050 Exploded Views - 2 A 1 2 3 4 5 BCD A201 A202 A215 A214 A213 A211 A203 A205 FACET(1) x 4PCS. A204 FACET(3) x 3PCS. 838430088GR 3TTB+8B(3BC)
16、x 2PCS. A212 x 3PCS. NUT A210 F BRA(ET。AS) U0024 U0021 U0020 U0022 U0023 U0025 NUT Scews: 838430088GR 3TTB+8B。3B() A-9050 Exploded Views - 3 A 1 2 3 4 5 BCD U0011 U0030 A102 A101 A001 U0015 U0013 T901 U0014 U0010 U0016 A012 A011 A010 838430088GR Other Screws: 3TTB+8B(3BC) A013 A015 x 5PCS. Q526 Q524
17、 Q528 Q525 D900 Q523 Q527 Q529 A020 x 4PCS. A020 x 4PCS. x 2PCS. A111 x 2PCS. A005 x 7PCS. A003 x 4PCS. A002 x 4PCS. Q530 Q527A,Q528A,Q529A,Q530A A-9030/9050/M-5010/ADM-20.4 SCHEMATIC DIAGRAMS - 1 BLOCK DIAGRAM A 1 2 3 4 5 BCDEFGH 6 7 8 IJK SHEETDATEDESIGN DRAWING_No.TITLE DIR_DAC_CLK DIR_DAC_SDA VO
18、L_DATA VOL_CLK DIR_DAC_CLK DIR_DAC_SDA DIR_CS DAC_CS DAC_RESET SPRELAY_A SPRELAY_B ASb SW SP_LOAD_SW DIR_SDI IPROT VPROT RI I/O 12VTG_OUT 12VTG_IN RI I/O 12VTG_OUT VOL_DATA AMUTE VOL_CLK DIR_DAC_CLK DIR_DAC_SDA DIR_CS DIR_INT0 DIR_RESET DAC_RESET DAC_CS DIR_SDI AMUTE 12VTG_IN Auto on HP_MUTE DIR_INT
19、0 DIR_RESET AD_BALANCE AD_TREBLE AD_BASS STBY_ON DIRECT SPAB BassCon MODE RESET SP_LOAD_SW ASb SW 12V OFF Auto on APOWER IPROT SPRELAY_A SPRELAY_B VPROT VPROTECT HP_DET VOL_AD_DETECT VOL_DOWN VOL_UP REMIN SELECTOR SPRELAY_A SPRELAY_B IPROTECT FL out_p FR out_p FL out_n FR out_n RX4 DIR RX NC NC RX1
20、RX0 RX7 RX6 RX5 RX2 RX3 MPIO_B OPT 2ch DAC diDRC SDA/SCL diDRC diDRC SP-A SP-B SP-A LEFT +29dB SDOUT SCK0 BCK LRCK Main AMP FUSE AC IN Main AMP MPU +3.3V MPU Relay Volume Volume OPAMP OPAMP DAC Analog +5V Analog Analog +12V -12V +3.3V Digital Digital +7V Volume +5V DAC -7V Volume LINE OUT R2S15211FP
21、 BASS CONTOUR FL FR PCM9211 I2S For M-5010/ADM20.4 R5F212A7SNFA MAIN MPU SP-B 80Hz LPF BCETC-1273 BCETC-1277 BASS TREBLE BALANCE STBY_ON SPAB DIRECT BassCon BCDIS-1268 BCSW-1271 ASb SW SP_LOAD_SW 12V OFF Auto on 12V_TRIG_IN RI 12V_TRIG_OUT Pre OUT LINE1 LINE2 LINE3 LINE4 BCPS-1270 BCDG-1269 BCAF-126
22、7 BCETC-1275 WM8718 COAX1 COAX2 PHONO MM MPU, 12Vtrg Head Phone BCETC-1274 LINE6 Volume BCETC-1276 BCSW-1272 Remote Sensor Selector TONE TONE RIGHT Subwoofer Pre OUT +29dB Model No. A-9050 / A-9030 / M-5010 / ADM-20.4 SCHEMATIC DIAGRAM (PART-1) BLOCK DIAGRAM BLOCK DIAGRAM St.Tanaka15 A-9050/A-9030/M
23、-5010/ADM-20.4 SCHEMATIC DIAGRAM 14-May-2012 249.145912 RC-202981 Rev 24.576MHz T? NPT-* 2 3 1 LOUNDNESS LINE 5 LINE 4 LINE 3 LINE 2 LINE 1 OPT OPT COAX POWER ON LED POWER ON LED 1 2 3 4 5 6 7 8 9 PHONO DIRECT T? NPT-* NPJ-2PDWR705 5 2 1 4 3 3 1 2 OPT1 2 GND 3 VCC 1 OUT 3 1 2 5 2 1 4 3 5 2 1 4 3 5 2
24、 1 4 3 5 2 1 4 3 5 2 1 4 3 5 2 1 4 3 A-9030/9050/M-5010/ADM-20.4 SCHEMATIC DIAGRAMS - 2 AUDIO SECTION A 1 2 3 4 5 BCDEFGH 6 7 8 IJK NGISEDETADTEEHS DRAWING_No.TITLE RI GND_DG +12V_DG LchOUT RchOUT BASS_LOUT BASS_ROUT AGND ANA_R Lch GND_RL Rch LFE ANA_L GND_DG GND_DG -12VA GND_DG ADSW2 +3.3DG DAC_CS
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Onkyo-A9050-int-sm 电路图 维修手册 Onkyo A9050 int sm 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


