Onkyo-DVL-100-Service-Manual(1) 电路图 维修手册.pdf

《Onkyo-DVL-100-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Onkyo-DVL-100-Service-Manual(1) 电路图 维修手册.pdf（48页珍藏版）》请在收音机爱好者资料库上搜索。

1、DLV-100 SERVICE MANUALSERVICE MANUAL Digital Light Processing Projector MODEL DLV-100 100 - 120 / 200 - 240 V AC, 50 / 60 HzUUD Ref. No. 3701 Nov, 2001 M E N U E N T E R C A N C E L SELECT AUTO ADJUST PC CARD ACCESS STATUS POWER ON/ STAND BY SOURCE INPUT SAFETY-RELATED COMPONENT WARNING! COMPONENTS

2、IDENTIFIED BY MARK ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTA

3、BLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. RadioFans.CN 收音机爱 好者资料库 1. Application This specification sheet applies for DLV-100. Model DLV-100 NEC Model code 01152009 2. General2. General2. General2. General 2.1 Operation temperature range +5 +35 degree C (H

4、umidity 20-80%RH, not in the dewfall.) 2.2 Storage temperature range -10 +50 degree C 2.3 Power source 100 120 VAC / 200 240 VAC +/-10%, 50 / 60 Hz 2.4 Input Current 2.2/1.1A (MAX.) 2.5 Inspection condition Inspection shall be done by AC120V / 60 Hz unless no rule is specified. As for the projection

5、 condition, the screen is perpendicularly installed to the set and the projection screen is in WIDE condition of 60 inches. When test, inspector shall be 2 +/- 0.3 m away from the screen. Fig. 1 Condition 3. Main parts specifications3. Main parts specifications3. Main parts specifications3. Main par

6、ts specifications 3.1 DMD panel Single Chip Digital Micromirror Device(DMD) 1024 x 768 pixels 3.2 Lens Manual zoom and focus F-no.=2.612.84, f=28.3534.02mm 3.3 Lamp 135W DC Lamp Average lifetime 1,000H The definition of average lifetime is the time that light becomes half with the continuous lightin

7、g-up. (Notes) The lamp bulb can be ruptured, while using a projector. When the lamp bulb is ruptured, there is a small crack and pieces of glass, which may be scattered in the lamp case. 20.3 m Screen Inspector DLV-100 RadioFans.CN 收音机爱 好者资料库 4. Electric specifications4. Electric specifications4. El

8、ectric specifications4. Electric specifications 4.1 Input signal band width RGB80MHz Video6.5MHz 4.2 Graduation 256 grade full color (16,777,216 color) 4.3 Display resolution NTSC/PAL/YCbCr550TV lines SECAM300TV lines RGB1024dots(H)768dots(V) 4.4 Input terminal RGB1 input: Mini D-SUB 15pin YCbCr:sha

9、res with the RGB terminal VIDEO1 input: RCA S-VIDEO1 input: DIN 4pin Audio1 input: Stereo mini jack PC Control1 input: DIN 8pin USB1 input: Type A PC Card1 input: CompactFlash 4.5 PC Card Viewer This Viewer can display the JPEG/BMP image which is preserved in CompactFlash (CF). CF correspond to SanD

10、isk CF 128Mbytes media. 4.6 Y/C Separation NTSC/PAL 4.7 Input signal (RGB) Horizontal Freq.15 100KHz(RGB: 24KHz or over) Vertical freq. 50 120Hz Pixel clock freq.Less than 100MHz Capable resolutionUXGA 1600dot(H)1200dot(V) Max. Sync systemSeparate Sync/Composite Sync/Sync on G 4.8 Input signal level

11、 RGBHV Input R,G,B0.7Vp-p / 75ohm positive Y1.0Vp-p / 75ohm positive Cb,Cr(Pb,Pr)0.7Vp-p / 75ohm H/V Sync4.0Vp-p / TTL posi./nega Composite Sync4.0Vp-p / TTL posi./nega Sync on G0.3Vp-p / 75 ohm negative VIDEO1.0Vp-p / 75 ohm S-VIDEOY:1.0Vp-p / 75 ohm C:0.283Vp-p / 75 ohm AUDIO0.5Vrms / 22 K ohm 4.9

12、 Audio output 1W monaural Speaker DLV-100 RadioFans.CN 收音机爱 好者资料库 4.10 On Screen Display 1. Pull down menu Basic/Custom menu Advanced menu 2. Multilingual menu English / French /German / Italian / Japanese / Spanish / Swedish 4.11 Remote Palm type remote unit 4.12 Input current 2.2A 100 120VAC/1.1A

13、200 240VAC 4.13 Plug when the indica- tor is orange, it is in standby mode. 4. Source Button Use this button to select a video source such as a PC, VCR, DVD player or PC Card Viewer (CompactFlash card). Each time this button is pressed, the input source will change as follows: RGB Video S-Video PC C

14、ard Viewer If no input signal is present, the input will be skipped. 5. Auto Adjust Button (RGB only) Use this button to adjust Position-H/V and Pixel Clock/Phase for an optimal picture. Some signals may not be displayed correctly or take time to switch between sources. 6. PC Card Access Indicator L

15、ights while accessing a CompactFlash memory card. 7. Enter Button Executes your menu selection and activates items selected from the menu. 8. Cancel Button Press this button to exit Menus. Press this button to return the adjustments to the last condition while you are in the adjustment or setting me

16、nu. 9. Select (LM? ?) / Volume (+) () Buttons LM:Use these buttons to select the menu of the item you wish to adjust. When no menus appear, these buttons work as a volume control. ? ?:Use these buttons to change the level of a selected menu item. A press of the ? button executes the selection. When

17、the menus or the Viewer tool bar is not displayed, these buttons can be used to select a slide, or to move the cursor in Folder List or Slide List. When the magnifying glass is displayed, these LM? ? buttons move the magnifying glass. 10. Menu Button Displays the menu. PC CARD USB VIDEO S-VIDEORGB A

18、UDIO PC CONTROL E N T E R C A N C E L SELECT AUTO ADJUST PC CARD ACCESS STATUS POWER ON/ STAND BY SOURCE M E N U 10 9 8 7 6 5 4 1 3 2 DLV-100 Terminal Panel Features 1. Audio Input Mini Jack (3.5 mm ) This is where you connect audio output from your computer, VCR, DVD player or laser disc player. A

19、commercially available audio cable is required. 2. RGB Input/ Component Input Connector (Mini D-Sub 15 pin) Connect your PC or other RGB equipment such as IBM or com- patible computers. Use the supplied RGB cable to connect to a PC. Or connect a Macintosh computer here using the supplied RGB cable.

20、This also serves as a component input connector that allows you to connect a component video output of component equip- ment such as a DVD player. 3. S-Video Input (Mini DIN 4 Pin) Here is where you connect the S-Video input from an external source like a VCR. NOTE: S-Video provides more vivid color

21、 and higher resolution than the traditional composite video format. 4. Video Input (RCA) Connect a VCR, DVD player, laser disc player, or document cam- era here to project video. 5. PC Card Eject Button Press to eject a CompactFlash memory card. 6. PC Card Slot Insert a CompactFlash memory card here

22、. 7. PC Control Port (Mini DIN 8 Pin) Use this port to connect your PC to control your projector via a serial cable. This enables you to use your PC and serial communi- cation protocol to control the projector. If you are writing your own program, typical PC control codes are on the back cover page.

23、 A cap is put on the port at the factory. Remove the cap when using the port. 8. USB Terminal Connect a commercially available mouse that supports USB. You can operate the menu or PC Card Viewer with the USB mouse via this terminal. Note that this terminal is not used with a computer and that there

24、may be some brands of USB mouse that the projector does not support. 9. AC Input Connect the supplied power cables three-pin plug here. When you plug the other end into an active wall outlet, the POWER indicator turns orange and the projector is in standby mode. 10. Built-in Security Slot ( ) This s

25、ecurity slot supports the MicroSaver Security System. MicroSaver is a registered trademark of Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc. AC IN PC CARD USB M E N U E N T E R C A N C E L SELECT AUTO ADJUST PC CARD ACCESS TUS POWER ON/ STAND BY SOURCE VIDEO

26、 S-VIDEORGB AUDIO PC CONTROL 2 3 4 5 7 8 9 10 6 1 DLV-100 Remote Control Features 1. Infrared Transmitter Direct the remote control toward the remote sensor on the projec- tor cabinet. 2. Standby/On Button If the main power is applied, you can use this button to turn your projector on or put it in s

27、tandby. 3. S-Video Button Press this button to select an S-Video source from a VCR. 4. Video Button Press this button to select an NTSC, PAL, SECAM or NTSC4.43 compatible video source from a VCR, DVD player, laser disc player or document camera. 5. RGB Button Press this button to select a video sour

28、ce from computer or compo- nent equipment connected to your RGB port. 6. Auto Adjust Button Use this button to adjust an RGB source for an optimal picture. Some signals may not be displayed correctly or take time to switch between sources. 7. Magnify + - Buttons Use this button to adjust the image s

29、ize up to 400%. To change the position of the magnified screen, press one of the LM? ? buttons to recall the magnifying glass, then use the LM? ? buttons to move the screen. 8. Volume + - Buttons Press + button to increase the volume and - button to decrease it. 9. ASPECT Button Press this button to

30、 select the screen size. 10. Mute Button This button turns off an image and sound for a short period of time. Press again to restore the image and sound. NOTE: When the menu is displayed, a press of this button mutes an image and sound without turning off the menu. 11. PICTURE Button Press this butt

31、on to recall and display the screen-related menu. 12. Freeze Button This button will freeze a picture. Press again to resume motion. 13. Menu Button Displays the menu for various settings and adjustments. 14. LAMP RESET Button If the lamp has been turned on for more than 1,600 hours (Normal mode), t

32、he power to the unit will be cut off and no messages will be displayed. Press and hold down this button for 10 seconds or more while the unit is in stand-by mode to clear the lamp available time and the lamp usage time. Supplied Remote Control INPUT 1 2 3 8 9 15 5 6 7 11 12 13 1716 14 10 4 15. LM? ?

33、 (Select) Buttons L,M:Use these buttons to select the menu of the item you wish to adjust. ?, ?:Use these buttons to change the level of a selected menu item. A press of the ? button executes the selection. When the magnifying glass is displayed, these LM? ? buttons move the magnifying glass. 16. Ca

34、ncel Button Press this button to exit Menus. Press this button to return to the previous menu without storing the current settings or adjustments when you are in the submenu or adjustment screen. 17. Enter Button Press this button to execute the selected item. When this is pressed, the adjustments a

35、nd settings are saved, and the display is returned to the menu. DLV-100 DISASSEMBLY In regard to the part name and the part number of each symbol, please refer to the parts table. S05 M10 S05 M04 M01 M03 M13 E05 E06 M11 M11 M14 S05 M12 S05 S05 S05 S07 M07 E02 M08 S06 M05 M06 A01 S02 S03 S04 E01 M26

36、M26 S01 M25 M26 M24 S01 M47 M48 M27 M09 S05 E04 M21 M22 S05 S01 M23 S05 S14 E11 E10 S05 M19 M20 A02 S08 S01 S08 E03 M15 S08 S09 S10 E08 S12 S08 M16 S08 S08 S13 M17 E07 S08 S11 E09 M46 M18 S16 S15 E12 S16 M29 M28 M30 M38 M37 M31 M45 S05 S05 S05 M43 S05 M40 M44 M39 M41 M42 S05 S05 M35 M36 S18 E14 S17

37、M32 E13 A03 M34 M33 DLV-100 BLOCK DIAGRAMS DLV-100 DLV-100 DLV-100 DLV-100 DLV-100 DLV-100 DLV-100 DLV-100 DLV-100 DLV-100 CONNECTION DIAGRAMS DLV-100 DLV-100 REPLACEMENT PART LIST C-No Description Part number PWB ASSYS E08 MAIN PWB ASSY 81E94FA1 E07 SUB PWB ASSY 81E94FB1 E03 REM PWB ASSY 81E94FC1 E

38、LECTRICAL PARTS & MISCELLANOUS PARTS 4 POWER SUPPLY(BALLAST) 3N100131 5 POWER SUPPLY(DC) 3N100002 E05 FAN (LAMP) 3N170021 E06 FAN (PSU) 3N170022 SW5501 POWER SWITCH LM3525MX-H 3N7J0001 SPEAKER 20*35MM 8H 1W 6N300004 CN3P(RM)105W,1685-26 7NW3W005 CN8P(PB)175W,1685-26 7NW8W001 CN11P(PA)65W,1685-26 7NW

39、AW001 M37 ZOOM LENS(01 DLP) 12JS2691 M24 BOTTOM COVER BK ASSY 24PS2901 COVER(LENS Z) 24F35271 M47 FILTER(F) 24F32641 CAP(PC CONTROL) 24F32691 M03 PANEL(FAN B) 24F34621 M09 HOLDER(BALLAST B) 24F34641 21 HOLDER(FAN 20) 24F34651 M48 LENS CAP ZK 24F35641 TERMINAL PANEL B ASSY 24FT8071 FILTER(B) 24F32651

40、 M04 TERMINAL PANEL B 24F35331 COVER(VIEWER B) 24F35341 SPRING(VIEWER) 24H35091 BRACKET(I/O) 24H37602 BRACKET(I/O) 24H37611 BRACKET(TOP) 24H39781 M15 PLATE(I/O B) 24H41781 M16 SHEET,INSULATOR(TOP) 24J16122 M17 SHEET,INSULATOR(CPU-PWB) 24J16133 M46 SHEET,INSULATOR(POWER) 24J16143 SPACER(7*7*3.5) 24J1

41、6401 SPACER(210*10*5) 24J16411 SPACER(70*10*5) 24J16421 SPACER(50*10*5) 24J16431 SPACER(REAR FOOT) 24J16451 SHEET(LENS CAP Z) 24J18241 41 CUSHION(T1*5*28) 24J19401 CAUTION LABEL(SERVICE U) 24L45241 CAUTION LABEL(SERVICE J) 24L45251 NAME PLATE 24L47221 CAUTION LABEL(LENS K) 24L47231 CAUTION LABEL(HOT

42、 K) 24L47241 CAUTION LABEL(ELEC SHOCK K) 24L47251 M01 TOP COVER ASSY K(XGA-Z) 24PS2891 BUTTON(TILT FOOT A) 24G07911 BRACKET(TOP) 24H37401 SPRING(TILT BUTTON) 24H37421 CUSHION(T8*7*4) 24J19391 SW PANEL(PA14) 7N900221 54 LABEL(1*10) 25765841 S09 SCREW(D-SUB) 24N03112 56 CBIPS*2.6*6*15BF 24N04011 S11 S

43、TAD(M2.5,H23.7,M/FM) 24N04861 S13 STAD(M2.5,H13,FM/FM) 24N04871 S01 SPECIAL SCREW(M2.5*6*3KF) 24N04881 S12 SPECIAL SCREW(P2*6*15BF) 24N04891 PUSH NUT(1.5) 24N04901 S08 SPECIAL SCREW(2.5*4*3GF) 24N04911 SPECIAL SCREW(2.5*4*3GF) 24N04921 SPECIAL SCREW(4*4*3KF) 24N04931 SCREW,SL-CPIMS*2*6*15BF 910D2031

44、 NUT,AHEXIN*2*15BF 91430201 M11 FAN RUBBER 79T08867 M14 FAN GUARD 79T08870 C-No Description Part number A02 LAMP HOUSE ASSY (M20+M19+M22+M21+M23) 79T09114 E11 THERMISTOR ASSY 79T08873 M10 LENS BASE POLYURETHANE FOAM 79T08877 E10 LIMIT SW BOARD ASSY 79T08878 M18 BRACKET(I/O) 79T08879 M07 BALLAST LOCK

45、 BASE 79T08880 M08 INSULATE SHEET L/D-N 79T08881 E04 BALLAST CONNECTOR 79T08884 M26 REAR FOOT RUBBER 79T08886 M27 REAR FOOT 79T08887 M25 FRONT FOOT 79T08888 A01 LAMP COVER ASSY (M05+M06+S03+S04) 79T09113 S02 POLYSLIDER CUT W 79T08930 S15 WHEEL SCREW 79T08893 E12 WHEEL SENSOR BOARD ASSY 79T08894 M28

46、WHEEL COVER 79T08895 M29 COLOR WHEEL UNIT 79T09112 M30 RUBBER SHEET 79T08896 M32 FORMATTER BRACKET 79T08933 A03 DMD SET(XGA) (E13+M33+M34+E14) 79T09115 M33 ELASTOMER HOLDER 79T08900 M34 ELASTOMER 79T08901 1M35 HEAT SINK A 79T08934 1M36 HEAT SINK B 79T08935 1M39 LENS BASE ASSY (M31+M40+M41+M42) 79T09

47、111 M43 LENS BASE COVER 79T08906 M44 APERTURE 79T08907 M45 INSULATE SHEET LB-U 79T08908 S18 SCREW No.6-12 79T08918 S14 SCREW 2.6-5 79T08922 S07 SCREW 3-6 79T08923 S06 SCREW M3-6 79T08924 PRINTED & PACKING MATERIALS BAND (L=100) 24280701 SOFT CASE(DLV-100) 24BS6971 SPACER 24M16321 PROTECTION BOX(300*

48、460) 24M16531 CARTON BOX 24MU6831 BATTERY LR6GRSP2A 6N800005 POWER CODE UC3 L3.0 M K 7N080201 RC-473E 7N900271 STRAP 24C05051 PUSH RIVET 24C04531 CABLE,RGB 7N520001 METHOD OF DISASSEMBLY 2. TOP COVER ASSY (1) Remove the five screws 1, and take out the TOP COVER ASSY. Note) This action must be taken

49、carefully because the FFC of SW PANEL and SPEAKER CABLE is connected to the MAIN PWB ASSY. TOP COVER ASSY 1 1 1 1 SW PANEL DLV-100 METHOD OF DISASSEMBLY 3. PANEL (FAN)/TERMINAL PANEL/FILTER (F) (1) Take out the PANEL (FAN) and the TERMINAL PANEL, FILTER (F). PANEL (FAN) TERMINAL PANEL FILTER (F) DLV-100 METHOD OF DISASSEMBLY 3. PANEL (FAN)/TERMINAL PANEL/FILTER (F) (1) Take out the PANEL (FAN) and the TERMINAL PANEL, FILTER (F). PANEL (FAN) TERMINAL PANEL FILTER (F) DLV-100 METHOD OF DISASSEMBLY 4. REPAIR LAMP/LAMP CO