Onkyo-HTR592-avr-sm 电路图 维修手册.pdf

《Onkyo-HTR592-avr-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Onkyo-HTR592-avr-sm 电路图 维修手册.pdf（63页珍藏版）》请在收音机爱好者资料库上搜索。

1、HT-R592 North American, Brazilian and Taiwanese models - “DIMMER” Asian models - “RT/PTY/TP” RC-863M AV RECEIVER Black model MODEL HT-R592(B) Ref. No. 4438 032013 120V AC, 60HzB MDF Black model for HT-S5600 120V AC, 60Hz 220-240V AC, 50/60Hz B MDC, B MDS B MMK, B MMQ RadioFans.CN 收音机爱 好者资料库 HT-R592

2、SERVICE PROCEDURE O1.00/13119AL D1.00/13125aLA M1.00/13302ALU MMPU (Main Microprocessor) DSP HDMI/Video Microprocessor Version displayed only for 3 seconds. e.g. e.g. e.g. M1.00/13302ALUVersion of MMPU displayed only for 3 seconds. e.g. -(TONE) -(TONE) -(TONE) +(TONE) +(TONE) +(TONE) 1. Replacing th

3、e fuses 2. Safety check out This symbol located near the fuse indicates that the fuse used is slow operating type, For continued protection against fire hazard, replace with same type fuse, For fuse rating, refer to the marking adjacent to the symbol. Ce symbole indique que le fusible utilise est e

4、lent. Pour une protection permanente, nutiliser que des fusibles de meme type. Ce demier est indique la qu le present symbol est apposre. Press ON/STANDBY button while pressing down VCR/DVR button when the unit is POWER ON, then the FL displays CLEAR, and turn to STAND-BY. Remove power cord from pow

5、er line. (U.S.A. model only) After correcting the original service problem, perform the following safety check before releasing the unit to the customer. Leakage current Check Measure the leakage current to a known earth ground (water pipe or conduct etc.) by connecting a leakage current tester betw

6、een the earth ground and exposed metal parts of the unit (input/output ground terminals, screw heads or metal overlays etc.). Plug the power supply cord directly into a 120Vac 60Hz wall socket and turn ON/STANDBY button on. Any current measured must not exceed 0.5mA. 3. To initialize the unit F6401,

7、 F6402 F6401, F6402 or F901 F901 or F901 F901 or R9001 10A-UL/T-233 10A-T/UL-ST2 8A-UL/T-233 8A-T/UL-ST2 4A-SE-EAK 4A-SE-TL250V 5A-UL-125V 252330GR 252333GR 252329GR 252261GR 252077GR 252277GR 252385T ! ! ! ! ! ! ! FUSE FUSE FUSE FUSE FUSE FUSE FUSE REF NO.PART NAMEDESCRIPTIONPART NO.REMARKS Notes :

8、 120V,Canadian model : 120V,Taiwanese model : 120V,Brazilian model : 220/230-240V, Korean model : 220/230-240V,Hong kong model 4. To check version of each Firmware a. Push STANDBY/ON key while pushing down DISPLAY key to display MMPU(Main Microprocessor) version. b. In display version, + (TONE) key

9、and - (TONE) key are pushed to display another F/W version. RadioFans.CN 收音机爱 好者资料库 HT-R592/ 2295 DEBUG MODE-1 AUDIO DEBUG MODE-1/3 To set in Debug mode 1. Press and hold down DISPLAY button, then press ON/STANDBY button. D1.00/13125aLA M1.00/13302ALU AUDIO dubug mode4D48K1N 0FFPo0 e.g. The version

10、number of microprocessor is displayed only for 3 seconds. The version number of DSP is displayed only for 3 seconds. The operations of DSP and DIR etc are able to checked by the information displayed on FL in this debug mode. This information will help to analysing digital audio no sound trouble. Ex

11、it e.g. e.g. e.g. 2. Press + (TONE) button while the version number of microprocessor is displayed. 3. Press DISPLAY button while the version number of DSP is displayed. 4. Press DISPLAY button. Contents of Display Number of digits - FL Display (e.g.) Number of digits ContentsState 1DIR INPUT LOCK/U

12、NLOCKE:UNLOCK :LOCK 2DIR INPUT RX 0:None 1:COAX1 2:COAX2 3:OPT1 4:OPT2 5:FRONT 8:HDMI1 9:HDMI2 3DIR/ADC,FIX MODED:Digital(SPDIF) A:Analog M:AnalogMultich p:PCM FIXED d:DTS FIXED 4-6Sampling Freq,Emphasis32K: 32 kHz w/o Emphasis 44K: 44.1kHz w/o Emphasis 48K: 48 kHz w/o Emphasis 64K: 64 kHz 88K: 88.2

13、kHz 96K: 96 kHz 176:176.4kHz 192:192 kHz 32e: 32 kHz w Emphasis 44e: 44.1kHz w Emphasis 48e: 48 kHz w Emphasis 7DIR DETECT TYPE0:Analog 1:PCM 2:Not PCM 3:Data 4:DTS CD(Not used) 5:Multich 6:Not Decided 8CODEC CLOCK MODEN:Normal U:Up Sampling H:High Sampling(Double Rate) D:Down Smapling Q:Quad Rate 1

14、0DSP PORTbit0:NIC bit1:DEC bit2:BUSY bit3:EXEC WAIT Refer to NIC DEC SPI Busy Ecec wait in DEBUG MODE-2 11-12DSP SEQUENCE00-FE:NotFree 2D:Mute Control FF:Free Refer to DSP Sequence in DEBUG MODE-3 13DSP DETECT FORMATP:PCM(Analog) D:Dolby Digital d:DTS A:AAC d:DTS A:AAC S:DSD p:DolbyDigital+ T:TrueHD

15、 H:DTSHD High Resolution M:DTSHD MaterAudio ?:UNKNOWN 14DSP DECODE OKo:OK x:NG 15Mute1:Selector 2:Effector 4:DSP 8:DIR 4D48K1N0FFPo0 123456789101112131415 RadioFans.CN 收音机爱 好者资料库 DEBUG MODE-2 AUDIO DEBUG MODE-2/3 HT-R592/ 2295 NIC/DEC/SPI Busy/Exec wait 0Stable state Internal stateInferred state 1NI

16、C 2 DEC 3NIC+DEC 9Exec wait + NIC 8 Exec wait If you stop at these numbers, please check the DSP Sequence. If the stop remains 1 is indicated, it is possible that there is an abnormality in the connection between the microcomputer and the NIC. 4SPI Busy 5SPI Busy + NIC 6SPI Busy + DEC 7SPI Busy + NI

17、C + DEC F Exec wait + SPI Busy + NIC + Dec E Exec wait + SPI Busy + DEC D Exec wait + SPI Busy + NIC CExec wait + SPI Busy BExec wait + NIC+DEC AExec wait + DEC Display contents Please check if the input signal Dolby / DTS / AAC / PCM from Coax or OPT. If the stop remains “2” is indicated, it is pos

18、sible that there is an abnormality in the connection between the DIR and the DSP. There is a case of 2 for the state to stop or pause playback equipment. And it is normal. If the stop in these numbers, it is possible that there is an abnormality in the connection between the DSP and the microcompute

19、r. If the stop remains 3 is indicated, it is possible that there is an abnormality in the connection between the microcomputer and the NIC. DEBUG MODE-3 AUDIO DEBUG MODE-3/3 HT-R592/ 2295 DSP Sequence Possible Causes Display contents Inferred state Stop at 03 is indicated. Stop at 05 is indicated. S

20、top at 08 is indicated. Stop at 09 - 0C is indicated. Stop at 17 is indicated. Have not been able to communicate between the microcontroller and the DSP. Have not been able to write from the boot loader of the DSP. While running the boot loader of DSP, the main program is not running. Main program o

21、f DSP is not working properly. There is a possibility that the power is turned off during the S / PDIF Update. 1.There is a problem with the connection between the FlashROM and the DSP, and the SDRAM. 2.Power is not supplied to the DSP. 3.Operation clock is not input to the DSP. 4.Reset port of the

22、DSP is not connected. 5.There is a problem with the line of communication between the microcontroller and DSP. 6.DSP is broken or Microcomputer. 7.Program has not been successfully written to the Flash ROM. Or the program is not written. 8.Communication port (such as DIR) other devices are connected

23、 to t he SPI mode is broken short. Terminals are short-circuited. 1.Program is not written correctly to Flash ROM. 2.DSPSDO line of microcomputer is interrupted somewhere. 3.There is a problem with the FlashROM (or SDRAM) of DSP. 4.DSP is broken or Microcomputer. 5.Upper address bus of Flash ROM is

24、not connected properly. 1.SDRAM is broken or Flash ROM. 2.Upper address bus of Flash ROM is not connected properly. 3.Program is not written correctly to Flash ROM. 4.There is a possibility that the power is turned off during the S / PDIF Update. 1.SDRAM is broken or Flash ROM. 2.Upper address bus o

25、f Flash ROM is not connected properly. 3.Program is not written correctly to Flash ROM. 4.There is a possibility that the power is turned off during the S / PDIF Update. Solution : Hold down the VCR/ DVR when the power is turned on, press the On/Standby key. (Clear) When out of the state of S / PDIF

26、 Update, please press the On/Standby key. Stop at 22-24 is indicated. Stop at 30-33 is indicated. Stop at 26-2F is indicated. Stop at FF is indicated. Main program of DSP is not working properly. main program of DSP is not working properly. The audio signal is not input. main program of DSP is not w

27、orking properly. The audio signal is not input. DSP settings has failed. The DSP is functioning properly. 1.SDRAM(or Flash ROM) is broken. 2.Upper address bus of Flash ROM is not connected properly. 3.Program is not written correctly to Flash ROM. 4.Operation clock to the DSP is not a predetermined

28、value. 1.SDRAM(or Flash ROM) is broken. 2.Upper address bus of Flash ROM is not connected properly. 3.Program is not written correctly to Flash ROM. 4.Operation clock to the DSP is not a predetermined value. 5.Audio clock to the DSP is not a predetermined value. 1.SDRAM(or Flash ROM) is broken. 2.Up

29、per address bus of Flash ROM is not connected properly. 3.Program is not written correctly to Flash ROM. 1.SDRAM(or Flash ROM) is broken. 2.Upper address bus of Flash ROM is not connected properly. 3.Program is not written correctly to Flash ROM. All settings are completed, DSP has started normal op

30、eration. Stop at “21”, to return to the previous display after a while. Format display indicator flashes. There is no sound even though it is the display of FF. Refer to “NIC/DEC/SPI Busy/Exec wait” in DEBUG MODE-2 HT-R592/ 2295 DEBUG MODE-4 HDMI DEBUG MODE-1/4 HDMI-related operations can be checked

31、 to some extent by displaying HDMI debug mode. To enter this mode Hold down DISPLAY button for 3 seconds. Information display will last for about 8 seconds. Input resolution Output resolution List of standard resolution 480i/60 480p /60 1080i/60 720p /60 1080p /60 240p /60 #480i/60 #480p /60 #240p /

32、60 576i/50 576p /50 1080i/50 720p /50 1080p /50 288p /50 #576i/50 #576p /50 #288p /50 1080p /24 1080p /25 1080p /30 V G A 1080i100 720p 100 576p 100 576i100 1080i120 720p 120 480p 120 480i120 576p 200 576i200 480p /60 480p 240 480i240 *480p /60 *576p /50 720p /24 720p /25 720p /30 1080i/60 1080i/60

33、Display of Input Resolution DVI input signal VGA input signal No input “I” and “P” will be capitalized. Display the ” ” in column 1 480I/60 480P /60 *V G A U nkno w n Resolution display method HT-R592/ 2295 DEBUG MODE-5 HDMI DEBUG MODE-2/4 i / p will be capitalized. Display the ” ” in column 5 Displ

34、ay the ” ” in column 14 Display the ” # ” in column 14 Display the ” x ” in column 14 Display the ” ” in column 4 4K Upscaling Display of Output resolution Display of Input resolution If the three-digit numbers are refrate List of resolution Resolution Error EDID_READ_NG Dislay of Output Resolution

35、For a video processor DVI input signal VGA input signal RSEN is OFF EDID_READ is NG Resolution Error No output (Signal output destination can not be found.) Hot-plug of Sink equipment can not be detected. Via VSP VSP skip 1080i/60 1080i/60 480I/60 480P /60 *480p/60 480p/60* 480p/60# 480p/60 x - O F

36、F 1080i/60 *x*p /* * 3840 x2160p /30 3840 x2160p /25 3840 x2160p /24 4096x2160p /24 3840 x2160p /30 x 3840 x2160p /30# 3D Display Display the ” ” in column 14 Display the ” # ” in column 9 Display the ” x ” in column 13 3D format INPUT/OUTPUT Resolution display Status Display RSEN OFF EDID READ NG R

37、esolution Error 1080p/24(3 D) H D M I44436bit Fra m eP a cking IN : O U T : 1080p/24(3 D )* H D M I444#36bit 1080p/24 ( 3 D)x HT-R592/ 2295 DEBUG MODE-6 HDMI DEBUG MODE-3/4 INPUT/ OUTPUT Status Input Mode Input Color Deep Color HDMI input DVI input No input RGB 422 444 24bit 30bit 36bit 3D format Fr

38、ame Packing Side-by-Side(Full) Side by Side(Harf) Field alternative Line alternative L+depth unknown Top and Bottom L+depth + graphics H D MI44436bit D VI44436bit -44436bit H D MIR G B36bit H D MI42236bit H D MI44436bit H D MIR G B26bit H D MIR G B30bit H D MIR G B36bit Fra m eP acking Falternative

39、Lalternative Sideby Side(F) L+ depth L+ depthgraphic Sideby Side(H) T op-and-B otto m U N K N O W N IN:*O U T:* HT-R592/ 2295 DEBUG MODE-7 HDMI DEBUG MODE-4/4 Input Resolution Output Resolution PC Resolution Display of Input resolution Display of Output resolution INPUT/ OUTPUT DVI input HDMI input

40、No input Three-digit numbers are Referat Display uppercase P/I Display lowercase p/i Horizontal resolutionVertical resolutionReferat Horizontal resolutionVertical resolutionReferat DVI output HDMI output Display”-” Three-digit numbers are Referat EDID READ NG Resolution through Display uppercase P/I

41、 Display lowercase p/i Display the ” # ” in column 13 Display the ” x ” in column 13 1024x768p /60 1024x768p /60 *x*p/* * 1024x768 P/60 1024x768p/60 1024x768 P 120 U N K N O W N *x*p/* 1024x768 P/60 1024x768p/60 - 1024x768 P 120 1024x768 P/60# 1024x768 P/60 x IN:*O U T:* HT-R592/ 2295 DEBUG MODE-8 S

42、ERVICE INFORMATION MODE Displaying Service information This service information display system is helpful in analyze the status when the unit goes into Protect mode and is powered off. Pay attention that the status will change if a button is pushed. 01:23 10h e.g. 1. Press twice the ON/ STANDBY key

43、while pressing the DISPLAY key. Listening Mode Code List - 80 F 27 DD e.g. Power off Cause T : Thermal Protect V : Voltage Protect I : Current Protect - : Other Temperature : xx F or xx C Volume LevelListenning Mode - Refer to the code list below. Time after Power on xx : xx Time after Initialize xx

44、 hour M1.00/13302ALU The version of main microprocessor is displayed only for 3 seconds. e.g. C_LM_LAST01 C_LM_PURE02 C_LM_DIRECT03 C_LM_STEREO04 C_LM_MONO05 C_LM_SURR20 C_LM_THX_MUSIC50 C_LM_THX_GAME70 C_LM_THX_CINEMA90 C_LM_THX_U2GAMEA0 C_LM_THX_U2MUSICA8 C_LM_THX_U2CINEMAB0 C_LM_ASCF4 C_LM_FLASHF

45、5 C_LM_DEBUGMODEF6 C_LM_FLASH2F7 C_LM_FLASH3F8 C_LM_FLASH4F9 C_LM_FLASH_CHECKFA C_LM_RPG0D C_LM_ACTION0E C_LM_ROCKBAND0F C_LM_SPORTS10 3. Press SETUP button again. The following information are displayed. 2. Press SETUP button within 3 seconds above. C_LM_AUDYSSEYD0 C_LM_DTSSS48 C_LM_ORCHESTRA06 C_L

46、M_UNPLUGGED07 C_LM_STUDIOMIX08 C_LM_TVLOGIC09 C_LM_ALLCHST0A C_LM_FULLMONO0B C_LM_TD0C C_LM_TESTTONEF1 C_LM_TESTTHRF2 C_LM_TESTAUTOF3 4. Press ON/STANDBY button to exit the display of service information. (Ref.: Press RETURN button to initialize the data in the service information.) ProtectData CLR

47、Normal display Information Displayed (Record this Information) Information Displayed (Record this Information) TX-NR525/HT-R592/HT-RC550 OPERATION CHECK-1 1.OPERATION CHECK(1/2) 1-1. OPERATIONS OF VOLTAGE-DETECTION PROTECTORS. See “OPERATION CHECK-3,-5” for TEST MODE operation. NOTE: Dont connect lo

48、ad nor short speaker terminals. a. Change the state to TEST-4-21. b. It tests by being automatic in order of TEST 4-21(FL+) 22(FR-) 23(C+) 24(SL-) 25(SR+) ( 26(SBL-) 27(SBR+) ). If TEST 4-27(TX-NR525/HT-RC550 are 4-25) is OK, it becomes the display of TEST-4-35. c. It will complete, if displayed on

49、FL TUBE as TEST 4-35. 1-2. OPERATIONS OF CURRENT-DETECTION PROTECTORS See “OPERATION CHECK-3,-5” for TEST MODE operation. a. Change the state to TEST-4-35. Even if you connect 3-ohm load for every channel of L, R, C, SL, SR, SBL and SBRch, a relay should not cut off. If 1-ohm load is connected for every channel of L, R, C, SL, SR,SBL and SBRch, a relay should hold the state of ON. 1-3. CONFIRMATION OF RDS (RADIO DA