Onkyo-TXSR702-avr-sm 电路图 维修手册.pdf
《Onkyo-TXSR702-avr-sm 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Onkyo-TXSR702-avr-sm 电路图 维修手册.pdf(131页珍藏版)》请在收音机爱好者资料库上搜索。
1、TX-SR702 TX-SR702/E SERVICE MANUALSERVICE MANUAL Ref. No. 3826 092004 120V AC, 60Hz 230-240V AC, 50Hz 120/220-230V AC, 50/60Hz 220-230V AC, 50Hz AV RECEIVER MODEL TX-SR702/E Black, Golden and Silver models BMDD,BMDC,SMDC BMPP,SMPP,BMPA,GMPA,GMPT GMWT GMGK,GMGQ,GMGR SAFETY-RELATED COMPONENT WARNING!
2、THE MARK FOUND ON SOME COMPONENT PARTS INDICATES THE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. WHEN REPLACING, BE SURE TO USE PARTS OF IDENTICAL DESIGNATION. MAKE LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE RE
3、TURNING THE APPLIANCE TO THE CUSTOMER. RC-588M RadioFans.CN 收音机爱 好者资料库 TX-SR702/E SPECIFICATIONS Amplifier Section Video Section Tuner Section FM AM General Video Inputs Video Outputs Audio Inputs Audio Outputs Other Jacks Specifications and features are subject to change without notice. Power Outpu
4、t 2 channel driven: American 100 W + 100 W (8 ,20Hz 20kHz,FTC) European: 130 W + 130 W (6 ohm ,1kHz,DIN) Asian: 160 W + 160 W (6 ohm ,1kHz,JEITA) Dynamic Power230 W + 230 W (3 ohm ,Front) 170 W + 170 W (4 ohm ,Front) 115 W + 115 W (8 ohm ,Front) THD (Total Harmonic Distortion)0.08 % (Power Rated) Da
5、mping Factor60 (Front,1kHz,8 ohm ) Input Sensitivity and Impedance200 mV/ 47 kohm (LINE) 2.5 mV/ 4.7 kohm (PHONO MM) Output Level and Impeadance200 mV/ 470 ohm (REC OUT) Phono Overload70 mV (MM 1kHz 0.5 %) Frequency Response10 Hz100 kHz/ +1 dB-3 dB (Direct mode) Tone Control10 dB, 50 Hz (BASS) 10 dB
6、, 10 kHz (TREBLE) SN Ratio106 dB (LINEIHF-A) 80 dB (PHONO,IHF-A) Speaker ImpedanceAmerican : 6 ohm other :4 ohm Input Sensitivity/Output Level and Impedance1 Vp-p /75 ohm (Component and S-Video Y) 0.7 Vp-p /75 ohm ohm (Component Pb/Cb,Pr/Cr) 0.28 Vp-p /75 ohm (S-Video C) 1 Vp-p /75 ohm (Composite) C
7、omponent Video Frequency Response5 Hz 50 MHz Tuning Frequency RangeAmerican: 87.5 MHz107.9 MHz Others : 87.5 MHz108.0 MHz Usable SensitivityStereo; 17.2 dBf 2 V(75 ohm IHF) Mono; 11.2 dBf 1 V(75 ohm IHF) S/N RatioStereo; 70 dB (IHF-A) Mono; 76 dB (IHF-A) THDStereo; 0.3 % (1kHz) Mono 0.2 % (1kHz) Fre
8、quency Response30 Hz15 kHz / 1 dB Stereo Separation45 dB ( 1kHz ) Tuning Frequency RangeAmerican: 530 kHz1700 kHz Others: 522 kHz1611 kHz Usable Sensitivity30 V S/N Ratio40 dB THD0.70% Power SupplyAmerican: AC 120 V, 60 Hz Australian and European: AC 230-240 V, 50 Hz Others : AC 120/220-230 V, 50/60
9、 Hz AC 230-240 V, 50Hz AC 220-230 V, 50/60 Hz Power ComsumptionAmerican : 8.1A Others : 700 W Stand-by Power Comsumption1.0 W Dimensions(W x H x D) 435 W x 175 H x 430 D mm 17-1/8 W x 6-7/8 H x 16-15/16 D inches WeightAmerican, Australian, European, Singapore and East southern asian:15.2 kg 33.5 lbs
10、 Others:16.0 kg 35.3 lbs Component Video Input 1,2,3 S-Video Compatible Jack InputDVD,VIDEO1,VIDEO2,VIDEO3, VIDEO4 A/V InputDVD,VIDEO1,VIDEO2,VIDEO3, VIDEO4 Component Video OutputOUT S-Video Compatible Jack OutputMONITOR OUT,VIDEO1,VIDEO2 A/V OutputMONITOR OUT,VIDEO1,VIDEO2 Digital InputsOptical : 5
11、 Coaxial : 2 Analog InputsDVD(MULTICHANNEL),VIDEO1,VID EO2,VIDEO3,VIDEO4,TAPE,CD,PHO NO Multichannel Inputs6 Digital OutputsOptical : 1 Coaxial : 1 Analog OutputsTAPE,VIDEO1,VIDEO2 Multichannel Pre Outputs7 Subwoofer Pre Outputs 1 Speaker Outputs9 Phones1 RS-232 Control1 (Not American, Australian) I
12、R Input1 12V Trigger Out1 RadioFans.CN 收音机爱 好者资料库 2. To initialize the unit This device employs a microprocessor to perform various functions and operations. If interference generated by an external power supply, radio wave, or other electrical source results in accident which causes the specified o
13、perations and functions to operate abnormally. To perform a result, please follow the procedure below. 1.Press and hold down the VIDEO-1 button, then press the STANDBY/ON button. 2.After CLEAR is displayed, the preset memory and each mode stored in the memory, such as surround, are initialized and w
14、ill return to the factory setting. 3. Unplug the power supply cord. 3. Safety-check out (U.S.A. model only) After correcting the original service problem, perform the following safety check before releasing the set to the customer. Leakage Current Check Measure leakage current to a known earth groun
15、d(water pipe, conduit, etc.) by connecting a leakage current tester between the earth ground and exposed metal parts of the appliance (input/output terminals, screwheads,metal overlays, etc.). Plug the power supply cord directly into a 120V AC 60 Hz outlet and turn Standby switch on. Any current mea
16、usred must not exceed 0.5mA. 1. Replacing the fuses This symbol located near the fuses indicates that the fuse used is fast operating type. For continued protection against fire hazard, replace with same type fuse. For fuse rating refer to the marking adjacent to the symbol. Ce symbole indique que l
17、e fusible utlise est a rapide. Pour une protection permanente, nuntiliser que fusibles de meme type. Ce darnier est la qu le present symbol est appse. 4.Setting the voltage selector (Worldwide models only) Worldwide models are equipped with a voltage selector to conform with local power supplies. Be
18、 sure to set this switch to match the voltage of the power supply in your area before plugging in the unit. Determine the proper voltage for your area: 220-230 V or 120 V. If the preset voltage is not correct for your area, insert a screwdriver into the groove in the switch. Slide the switch all the
19、 way to the upper (120 V) or to the lower (220-230 V), whichever is appropriate. 5.Setting the AM tuning step frequency (Worldwide models only) CIRCUIT NO. PART NO. DESCRIPTION Note: :120V model only : Other models except 120V model : Asian model only for 230V 120 V VOLTAGE SELECTOR 220-230 V 1 Pres
20、s the RECEIVER button fol- lowed by the SETUP button. The main menu appears onscreen. 2 Use the Up and Down / buttons to select 1. initial Setup, and then press ENTER. The Initial Setup menu appears. 3 Use the Up and Down / buttons to select 3. Hardware Setup, and then press ENTER. The Hardware Setu
21、p menu appears. 4 Use the Up and Down / buttons to select d. AM Fre- quency Step, and then use the Left and Right / buttons to select: 10 kHz: Select if 10 kHz steps are used in your area. 9 kHz: Select if 9 kHz steps are used in your area. 5 Press the SETUP button. The setup menu closes. RECEIVER E
22、NTER ENTER M enu - - - - - - - - - - - - - - - - - - - - - - - - 1. I ni t i al Set up 2. Speaker Set up Advanced Set up 3. Sur r ound Set up 4. Audi o Adj us t 5. Li s t eni ng M ode Pr es et 6. Pr ef er ence Bas i c Set up 1. I ni t i al Set up - - - - - - - - - - - - - - - - - - - - - - - - 2. Co
23、m ponent Vi deo 3. Har dwar e Set up 1. Di gi t al I nput 1- 3. Har dwar e Set up - - - - - - - - - - - - - - - - - - - - - - - - : Not Act i vat ed b. Sp I m pedance M i ni m um : 6ohm s c. TV For m at : NTSC d. AM Fr equency St ep : 9kHz a. Power ed Zone2 ENTER F6901,F6902 252303 or15A-TUL-250V or
24、 25219715A-UL/T-314,Fuse F901 252196 or12A-UL/T-314 or 25230112A-TUL-250V F902 252079 or6.3A-SE-EAK or 252245 or6.3A-SE-TL250V or 2522796.3A-SE-TL250V,Fuse F903 252164 or5A-UL/T-237 or 2522585A-T/UL-ST2 252075 or2.5A-SE-EAK or 252241 or2.5A-SE-TL250V or 2522752.5A-SE-TL250V F9501 252160 or2.5A-UL/T-
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Onkyo-TXSR702-avr-sm 电路图 维修手册 Onkyo TXSR702 avr sm 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


