Marantz-SR7300-avr-mz07069 电路图 维修手册.pdf

《Marantz-SR7300-avr-mz07069 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Marantz-SR7300-avr-mz07069 电路图 维修手册.pdf（3页珍藏版）》请在收音机爱好者资料库上搜索。

1、 100 Corporate Drive Mahwah, NJ 07430 Service Bulletin No. : MZ07-069 Date: June 22, 2007 _ Model: SR7300, SR7300F Subject: Software Update Information. Symptom: Update the software in order to minimize component over dissipation if the power amp fails. Solution: 1. Change the procedure for the prot

2、ection operation that may be performed while the unit is in operation. BEFORE UPDATE Originally, the unit was designed to go into STANDBY mode upon detection of an abnormality with the STANDBY LED flickering every 500m sec. it would never be powered on by the standby switch or the remote control, so

3、 component over dissipation never occurred. However, if the unit was plugged in again, it could occur before the unit went into standby a few seconds later. AFTER UPDATE The unit has been modified never to be powered on by any means once it goes into standby with the standby led flickering every 125

4、m sec., unless the specialized procedure (*1) described below is performed. *1: If the unit cannot be powered on after being plugged in again (with the STANDBY LED flickering every 125m seconds), the power amp has been damaged. The unit still can be powered on again through the following method, _ C

5、ONFIDENTIALITY NOTICE: The information contained in this document is intended for the exclusive use by MARANTZ Authorized Service Centers and their employees. This document may contain information that is privileged, confidential and may be protected from disclosure under applicable laws and terms o

6、f the MARANTZ Service Agreement. Any distribution, disclosure, dissemination or copying of this document and the information it contains is prohibited. No responsibility will be accepted by MARANTZ for any damage, injury or loss resulting from the misuse of the information contained in this document

7、. RadioFans.CN 收音机爱 好者资料库 but it can cause further damage the power amplifier. Please never let end-users perform this procedure. Set can be powered on by “FACTORY” KEY = DVD + TUNER + 7.1CH INPUT”. 2. Update the MAIN microprocessor firmware. After the update, please refer to the firmware version hi

8、story. 1) Firstly, please check the version of each software and DSP code. (For the procedure, refer to the Service Manual on Page 51 of the Service Mode.) 3. Update Software and NECESSARY PART Number 1) Firmware Ver:SR7300_070523_1.mot (For the procedure, please refer to the Service Manual on Page

9、53.) 2) NECESSARY PART No: 00M03AJ499A10 Check the firmware version. If it is found to not yet be updated, please perform the latest update. _ CONFIDENTIALITY NOTICE: The information contained in this document is intended for the exclusive use by MARANTZ Authorized Service Centers and their employee

10、s. This document may contain information that is privileged, confidential and may be protected from disclosure under applicable laws and terms of the MARANTZ Service Agreement. Any distribution, disclosure, dissemination or copying of this document and the information it contains is prohibited. No r

11、esponsibility will be accepted by MARANTZ for any damage, injury or loss resulting from the misuse of the information contained in this document. RadioFans.CN 收音机爱 好者资料库 _ CONFIDENTIALITY NOTICE: The information contained in this document is intended for the exclusive use by MARANTZ Authorized Servi

12、ce Centers and their employees. This document may contain information that is privileged, confidential and may be protected from disclosure under applicable laws and terms of the MARANTZ Service Agreement. Any distribution, disclosure, dissemination or copying of this document and the information it

13、 contains is prohibited. No responsibility will be accepted by MARANTZ for any damage, injury or loss resulting from the misuse of the information contained in this document. Attention: If you determine the update was not yet performed, please Update the DSP using the following procedure. 1) DSP Sof

14、tware file name: SR7300_DSP_040518.zip (For the rewriting procedure, please refer to the Service Manual on Page 53.) 2) The following are DSP Code IDs: CD01 02060104, CD02 02010116, CD03 02060206, CD04 02040113, CD05 02030306, CD06 02030114, CD07 02030211, CD08 02020206, CD09 02050211, CD0A 0205030A, CD0B 0205040D, CD0C 02050510, CD0D 02050110 Serial Number Range: Please implement this update to all units returned for repair. RadioFans.CN 收音机爱 好者资料库