Marantz-SR8001-avr-mz07106 电路图 维修手册.pdf

《Marantz-SR8001-avr-mz07106 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Marantz-SR8001-avr-mz07106 电路图 维修手册.pdf（6页珍藏版）》请在收音机爱好者资料库上搜索。

1、 100 Corporate Drive Mahwah, NJ 07430 Service Bulletin No. : MZ07-106 3rd Date: September 5, 2008 _ Model: SR6001, SR7001 SR8001 Subject: The thermal sensor is sometimes activated, which shuts down the unit putting the unit into standby.* * Perform the following rework if no faulty point (defective

2、output devices, DC offset, over voltage, over current, heat issue) is found that would activate the protection circuit and /or it still shows error message CHECK POW5 on the FLD. Symptom: The Heat Sensor is mounted on the PWB with a connector in order to detect a temperature rise with the Power Amp.

3、 When the connector has a loose connection, the protection circuit is activated, thereby causing a shut down. Solution: If no faulty point is found that would activate the protection circuit and /or it still shows error message CHECK POW5 on the FLD perform the following procedure. Replace the senso

4、r assembly and solder the lead wires directly to the PWB. 1. Detach the AMP PWB ASSY (POS NO. 38) from the Heat Sink and replace the Heat Sensor TH1 (CN81) with a new part (P/N 90M-HP000120R). _ CONFIDENTIALITY NOTICE: The information contained in this document is intended for the exclusive use by M

5、ARANTZ Authorized Service Centers and their employees. This document may contain information that is privileged, confidential and may be protected from disclosure under applicable laws and terms of the MARANTZ Service Agreement. Any distribution, disclosure, dissemination or copying of this document

6、 and the information it contains is prohibited. No responsibility will be accepted by MARANTZ for any damage, injury or loss resulting from the misuse of the information contained in this document. RadioFans.CN 收音机爱 好者资料库 2. Cut the white plastic connector (CN81) off the new Heat Sensor then strip i

7、nch (approx.) of insulation from the end of the lead and tin each end of the lead wire. (Fig. 1) _ CONFIDENTIALITY NOTICE: The information contained in this document is intended for the exclusive use by MARANTZ Authorized Service Centers and their employees. This document may contain information tha

8、t is privileged, confidential and may be protected from disclosure under applicable laws and terms of the MARANTZ Service Agreement. Any distribution, disclosure, dissemination or copying of this document and the information it contains is prohibited. No responsibility will be accepted by MARANTZ fo

9、r any damage, injury or loss resulting from the misuse of the information contained in this document. RadioFans.CN 收音机爱 好者资料库 3. Solder the stripped ends of the lead wires to resistors R811 and R812 as shown below. _ CONFIDENTIALITY NOTICE: The information contained in this document is intended for

10、the exclusive use by MARANTZ Authorized Service Centers and their employees. This document may contain information that is privileged, confidential and may be protected from disclosure under applicable laws and terms of the MARANTZ Service Agreement. Any distribution, disclosure, dissemination or co

11、pying of this document and the information it contains is prohibited. No responsibility will be accepted by MARANTZ for any damage, injury or loss resulting from the misuse of the information contained in this document. RadioFans.CN 收音机爱 好者资料库 Note: The Heat Sensor has no polarity however, be certai

12、n to connect the sensor to the side of each resistor that corresponds (electrically) to connector CN81s pins 1 & 2. Do not solder the leads to the side of resistors R811 and R812 that are closest to the base of transistor Q801. See Figure 3 for details. _ CONFIDENTIALITY NOTICE: The information cont

13、ained in this document is intended for the exclusive use by MARANTZ Authorized Service Centers and their employees. This document may contain information that is privileged, confidential and may be protected from disclosure under applicable laws and terms of the MARANTZ Service Agreement. Any distri

14、bution, disclosure, dissemination or copying of this document and the information it contains is prohibited. No responsibility will be accepted by MARANTZ for any damage, injury or loss resulting from the misuse of the information contained in this document. 4. Fix the soldered wire ends to the resi

15、stors using Sony bond SC608Z or Dow Corning SE 9188 RTV high temperature RTV. 5. Mount the new Heat Sensor to the heat sink. _ CONFIDENTIALITY NOTICE: The information contained in this document is intended for the exclusive use by MARANTZ Authorized Service Centers and their employees. This document

16、 may contain information that is privileged, confidential and may be protected from disclosure under applicable laws and terms of the MARANTZ Service Agreement. Any distribution, disclosure, dissemination or copying of this document and the information it contains is prohibited. No responsibility wi

17、ll be accepted by MARANTZ for any damage, injury or loss resulting from the misuse of the information contained in this document. After replacing the Heat Sensor use a felt tipped permanent marking pen to record the date the sensor was changed to the inside of the top cover (left side panel). _ CONF

18、IDENTIALITY NOTICE: The information contained in this document is intended for the exclusive use by MARANTZ Authorized Service Centers and their employees. This document may contain information that is privileged, confidential and may be protected from disclosure under applicable laws and terms of the MARANTZ Service Agreement. Any distribution, disclosure, dissemination or copying of this document and the information it contains is prohibited. No responsibility will be accepted by MARANTZ for any damage, injury or loss resulting from the misuse of the information contained in this document.