Marantz-SR9300-avr-mz04010 电路图 维修手册.pdf

《Marantz-SR9300-avr-mz04010 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Marantz-SR9300-avr-mz04010 电路图 维修手册.pdf（4页珍藏版）》请在收音机爱好者资料库上搜索。

1、Approved by S.NAGAO Written by WQ-19 2 817/additional rule 3 (1st Issue 2003-03-19) Date:27-Jan.-2004Model: SR8300/SR9300 Page:1 / 3REF.NBR:MZ04-010 Circulation:Application: Subject: Int.ref: PHENOMENON After Power switch on, “Clear memory” is displayed and SETUP sometimes returns to initial setting

2、. *According to the report, when the power plug is taken out and inserted to the outlet, the phenomenon is sometimes happened. SOLUTION 1) Update the CPUs software version to V0301233 First of all, please check the CPU (QU01) version. It can be confirmed on the “SERVICE PROGRAM”, please refer to the

3、 SR8200/SR9200 Service Manual on page 95 for the procedure. Please refer to the service manual SR8200/SR9200 page97 to 98 about details of “ 9.UPDATE FIRMWARE ”. As for details, Please see page 2/3 and 3/3 NECESSARY PART Update of the firmware disc *SR8300CDR REMARKS The countermeasure apply to this

4、 claim only. This problem apply to the following Lot number. SR8300 apply to MZxxxxxx21xxxx to MZxxxxxx38xxxx. (MZxxxxxx24xxxx except). SR9300 apply to MZxxxxxx19xxxx to MZxxxxxx37xxxx. SERVICE BULLETIN SETUP sometimes returns to initial setting. x for information customer complaint in case of servi

5、ce mandatory . See Below File name of *SR8300CDR V030123 3 RadioFans.CN 收音机爱 好者资料库 97 9. UPDATE FIRMWARE Software for CPU and DSP can be updated. Have *SR9200CDR update disc. There are two mode of download, regarding to the target of software as bellow. Mode 1: Download DSPs software to 4M Flash-ROM

6、. This mode is to update the software for DSP. The target devise is 4M Flash ROM (Q671) on P604. SR9200&8200 need to be set download condition, by three front keys. Mode 2: Download CPUs software to internal Flash-ROM. This mode is to update the software for DSP. The target devise is internal flash

7、ROM of CPU (QU01) on P604. The unit needs to be set to writing condition, by pushing internal switch from back-panel. The following items are required for updating. RS232C Dsub-9 pin cable (female to female/Straight type) PC (Windows 98, NT, ME, 2000) with RS-232C port. Upgrade software to CPU. Upgr

8、ade software to DSP. Use RS232C Dsub-9 pin cable (female to female/Straight type) to connect PC and the unit. COM port on PC needs to be set by dialog box for each program. COM port can be set from COM1 to COM5. Download Firmware for DSP (Mode 1) 1. Put the “DSP upgrade” folder into anywhere on your

9、 PCs hard disc. 2. Connect PC and the unit with the RS-232C cable. 3. Turn on the unit. 4. Press ENTER, MUTE and MULTI-SPK buttons simultaneously more than 5 seconds to turn the unit into Loading Mode. 5. “LOADING MODE” will be shown on FLD. 6. Launch “UpgradeDSP.exe” on PC. 7. Set the Baud Rate to

10、38400 then click Start communication button. If the connection is made successfully, a dialog box saying “Success to connect” appears and “CONNECTED” is displayed on FLD. 8. Click Send the DSP codes button on the dialog box. Progress status of downloading will be shown on PC and “LOADING” is display

11、ed on FLD. 9. If downloading is completed successfully, “COMPLETED” is displayed on FLD. And a dialog box saying Finished the DSP code transmitting appears. Click OK and then click CLOSE to close the application. 10. Turn off the unit. RadioFans.CN 收音机爱 好者资料库 page 2/3 *SR8300CDR Use Mode2: 98 Downlo

12、ad Firmware for CPU (Mode 2) 1. Put the “CPU upgrade” folder into anywhere on your PCs hard disc. 2. Connect PC and the unit with the RS-232C cable. 3. Remove the screw on the backside of the unit. 4. Insert a thin rot to the screw hole and push the switch (SU02) inside to turn on the switch. 5. Tur

13、n on the power of the unit. (Confirm that the stand-by LED lights in green so the unit is in the boot mode.) 6. Launch “H8Download.exe” on PC. 7. Click other files button in the dialog box to specify the file (XXXX.mot) to be upload. 8. Click Connect button. If the connection with the H8 -com is suc

14、cessfully made, a dialogue box saying “Success to the H8 micro processor connection” appears. If the connection fails, error message will appear. 9. Click Send button to start update. 10. If the firmware is updated successfully, a dialog box saying “Finished the firmware program sending” appears. 11

15、. Click CLOSE button to close the application. 12. Disconnect Mains power cord. 13. Turn off the internal switch that has been turned on at step 3. Put on the screw. 14. Turn on the unit. Firmware Version Check To check the versions of the firmware, see “Microprocessor (CPU), DSP Version and FLD Seg

16、ment Check Mode” in “SERVICE PROGRAM” section. RadioFans.CN 收音机爱 好者资料库 page 3/3 V0301233.mot Approved by S.NAGAO Written by WQ-19 2 817/additional rule 3 (1st Issue 2003-03-19) Date:22-Apr.-2004Model: SR8300/SR9300 Page:1 / 1REF.NBR:MZ04-035 Circulation:Application: Subject: Int.ref: PHENOMENON 1. B

17、y SETUP MENU, Set the Speaker level of SURROUND to +1dB or more. Then, escaping from MENU. 2. The Sound level is set to negative infinity from other than negative infinity by VOL Knob. 3. Press the POWER switch to turn off and turn on. 4. “Clear memory” is displayed and SETUP sometimes returns to in

18、itial setting. SOLUTION 1) Update the CPUs software version to V0301234 First of all, please check the CPU (QU01) version. It can be confirmed on the “SERVICE PROGRAM”, please refer to the SR8200/SR9200 Service Manual on page 95 for the procedure. Please refer to the service manual SR8200/SR9200 pag

19、e97 to 98 about details of “ 9.UPDATE FIRMWARE ”. As for details, Please see page 2/3 and 3/3 NECESSARY PART Update of the firmware disc *SR8300CD2 REMARKS The countermeasure applies to this claim only. SERVICE BULLETIN After specific operation, SETUP sometimes returns to initial setting. x for information customer complaint in case of service mandatory . ALL V030123 4 File name of *SR8300CD2