Pioneer-DJM3000-mix-sm电路图 维修手册.pdf

《Pioneer-DJM3000-mix-sm电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Pioneer-DJM3000-mix-sm电路图 维修手册.pdf（107页珍藏版）》请在收音机爱好者资料库上搜索。

1、 ORDER NO. PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01

2、, Singapore 159936 PIONEER CORPORATION 2002 DJM-3000 RRV2587 DJ MIXER DJM-3000 THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). ModelTypePorew Requirement The voltage can be converted by the following method. DJM-3000KUCXCNAC120V DJM-3000WYXCNAC220-240V DJM-3000RLBXCNAC110-120V/220-2

3、40VWith the voltage selector For details, refer to Important symbols for good services on the next page. T-ZZR APR.2002.printed in Japan RadioFans.CN 收音机爱 好者资料库 DJM-3000 2 1234 1234 C D F A B E SAFTY INFORMATION This service manual is intended for qualified service technicians; it is not meant for t

4、he casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and ma

5、y void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician. WARNING This product contains lead in solder and certain electrical parts contain chemicals which are k

6、nown to the state of California to cause cancer, birth defects or other reproductive harm. Health rotate counterclockwise to decrease the level (to ) 9 HI control (high-range equalizer) Use to adjust high-range frequency of input. When the dial is set to the center click setting, flat response is pr

7、ovided. Rotate clockwise to increase response (to +12 dB), and rotate counterclockwise to decrease response (to 26 dB). 0 MID control (mid-range equalizer) Use to adjust mid-range frequency of input. When the dial is set to the center click setting, flat response is provided. Rotate clockwise to inc

8、rease response (to +12 dB), and rotate counterclockwise to decrease response (to 26 dB). - LOW control (low-range equalizer) Use to adjust low-range frequency of input. When the dial is set to the center click setting, flat response is provided. “ 1 7 8 2 3 4 5 6 9 0 - ! 7 9 0 - ! 7 9 0 - ! 7 9 0 -

9、!% the Left channel becomes the source selected with the H.P CUE switch, while the Right channel becomes the master output sound (only when MASTER H.P CUE switch is set to ON). * MIXING control Use to adjust the headphones monitor sound. When rotated fully clockwise, the master output sound only is

10、heard (only when MASTER H.P CUE switch is set to ON). When rotated fully counterclockwise, only the channel selected with the H.P CUE switch (other than MASTER) is heard. At the center click position, the master output and source selected with the H.P CUE switch are at equal levels. ( LEVEL control

11、Use to control the headphones monitor level. When one of CH-1 to CH-4 is selected, this control is not affected by the MASTER fader lever (%) and the MASTER BALANCE control (). ) PHONES (headphones jack) Cross Fader Controls _ CROSS FADER ASSIGN A switch When using the cross fader with two sources (

12、A, B), this switch selects the source assigned to A. THRU: When cross fader is not used, sets to THRU. 1-4:Use to select the channel (CH-1 to CH-4) assigned to A. Channels other than those assigned to A and B can be output without passing through the cross fader. + CROSS FADER CURVE selector switch

13、Use to select one of three rising curve patterns for the cross fader function. Fader display A During the effect mix mode, displays the output of sounds from the channel selected with the CROSS FADER ASSIGN A switch. Cross fader lever Use to adjust the mix of sounds from the sources assigned to A an

14、d B by the ASSIGN switches (_) and (). Fader display B During the effect mix mode, displays the output of sounds from the channel selected with the CROSS FADER ASSIGN B switch. CROSS FADER ASSIGN B switch When using the cross fader with two sources (A, B), this switch selects the source assigned to

15、B. THRU: When cross fader is not used, sets to THRU. 1-4:Use to select the channel (CH-1 to CH-4) assigned to B. Channels other than those assigned to A and B can be output without passing through the cross fader. FADER START Switches CH-1, CH-2, CH-3, CH-4 When a CD player (CMX-3000, CMX-5000, CDJ-

16、1000, CDJ- 100S, CDJ-700S or CDJ-500II) is connected to one of the above channels of this unit via a control cord, the CD players CUE START/STOP operation will start when the channel fader is moved from “0” upwards, and will stop (back cue) when the channel fader is returned to “0”. The indicator of

17、 the selected channel will light orange during this operation. Also, if a channel is assigned to the cross fader, the cross fader is given priority; when the Cross fader lever begins moving from the A side toward B side, the CD player assigned to the B side will start, and when the lever reaches the

18、 B side, the A side source will stop (back cue). DJM-3000106 1234 1234 C D F A B E BEAT EFFECTS Controls 1-4 (Channel displays) Displays the channel selected for BPM count. AUTO BPM COUNTER When AUTO BPM is selected with the Effect selector switch (), displays the BPM of the channel (CH-1 to CH-4) s

19、elected with the H.P CUE switch (=). The indicator flashes during counting, or if it is unable to count BPM. BPM counter range selector switch BPM can be selected in one of the ranges 70-139, 91-180, 70-180 or manual mode. Set the range best matching the track you are measuring. BPM counter range di

20、splays Displays the BPM count range selected. When BPM count range 70-180 is selected, both indicators 70-139 BPM and 91-180 BPM light. If both indicators are out, it indicates manual mode. For more information about manual mode, see the item “BPM COUNTING”. If the Effect selector switch () is set t

21、o DELAY, ECHO, PAN, TRANS, FILTER or FLANGER, the indicator will display the BPM of the source selected with the Effect CH. SELECT switch (). 1-4, MIC, MASTER (Source displays) Displays the source selected with the Effect CH. SELECT switch (). If the Effect CH. SELECT switch is used to select “CF.A”

22、 or “CF.B”, the channel that lights will be the one (1-4) selected with the respective ASSIGN switch (_), (). PARAMETER 1 (Parameter 1 / BPM counter) The display contents change in accordance with the setting of the Effect selector switch (). When AUTO BPM is selected, the display shows the BPM of t

23、he source selected with the Effect CH. SELECT switch (). The indicator flashes during BPM counting, or when it is unable to count BPM. When SND/RTN is selected, nothing is displayed. When a setting other than AUTO BPM or SND/RTN is selected, the display shows the value of the effect set with Effect

24、PARAMETER 1 control (). BEAT (Effect synchronous displays / Beat displays) This displays contents differ depending on the setting of the Effect selector switch (). When DELAY, ECHO, PAN, or TRANS are selected, the display shows the equivalent parameter 1 value for the BPM of the selected source. The

25、 display lights when the beat is in the range 1/2 to 4/1. If the beat value is below 1/2, pressing the Effect beat selector switch () causes the value to become 1/4, and all display indicators go out. If the beat value is above 4/1, pressing the Effect beat selector switch (#) causes the value to be

26、come 8/1, and all display indicators go out. If the value does not match the number of beats, the indicator for the nearest beat value will flash. When FILTER or FLANGER are selected, the display shows the equivalent parameter 1 value for the BPM of the selected source. The display lights when the b

27、eat is in the range 1 to 16. If the beat value is below 1, pressing the Effect beat selector switch () causes the value to become 1/2, and all display indicators go out. If the value is above 16, pressing the Effect beat selector switch (#) causes the value to become 32, and all display indicators g

28、o out. If the value does not match the number of beats, the indicator for the nearest beat value will flash. When REVERB is selected, the display shows the amount of reverberation applied. When PITCH is selected, the display shows the amount of pitch modification applied. No display appears when AUT

29、O BPM or SND/RTN are selected. fi fl DJM-3000107 5678 56 7 8 C D F A B E Effect beat selector switches (, #) Use this switch to change the value of Effect PARAMETER 1 control () in accordance with the BPM of the source selected with the Effect CH. SELECT switch (). The setting value of this switch d

30、iffers depending on the setting of the Effect selector switch (). When DELAY, ECHO, PAN, or TRANS are selected, the parameter 1 value for the BPM of the selected source can be set to 1/4 beat, 1/2 beat, 1/1 beat, 2/1 beat, 4/1 beat, or 8/1 beat. When DELAY or ECHO are selected, values can be set to

31、1/4x, 1/2x, 1/1x, 2/1x, 4/1x or 8/1x, within a range such that the parameter 1 value does not exceed 3500 ms. When FILTER or FLANGER are selected, the parameter 1 value for the BPM of the selected source can be set to 1/2 beat, 1 beat, 2 beats, 4 beats, 8 beats, 16 beats, or 32 beats. When PITCH is

32、selected, the value can be set to 100%, 50%, 33%, 0%, 33%, 50%, or 100%. When REVERB is selected, the value can be set to 10%, 20%, 35%, 50%, 65%, 80%, or 90%. This control is disabled when AUTO BPM or SND/RTN are selected. H.P CUE (Headphones cue switch) When this switch is pressed it lights orange

33、, and beat effects are output to the headphones. Pressing the switch again disconnects the beat effect to the headphones and turns off the switch lamp. Effect selector switch Use to select desired effects. CH. SELECT (Effect channel selector switch) Use to select the source you wish to apply effects

34、 to. TIME (PARAMETER 1) (Effect parameter 1 control) This control is used to set the time parameter for the onboard effector. LEVEL/DEPTH (PARAMETER 2) (Effect parameter 2 control) This control is used to set quantitative parameters for the onboard effector. fi ON/OFF, TAP (Effect ON/OFF switch, TAP

35、 switch) This switch produces different operations depending on the setting of the Effect selector switch () When DELAY, ECHO, PAN, TRANS, FILTER, FLANGER, REVERB, PITCH, or SND/RTN are selected, the switch operates to turn the selected effect ON/OFF. OFF: the orange lamp lights; ON: orange lamp fla

36、shes. When AUTO BPM is selected the switch becomes a “TAP” switch; by tapping the switch together with the source beat, the BPM can be input manually. When tapping the TAP switch to count the BPM, both BPM counter range displays (70-139 BPM and 91-180 BPM) go out, and the manual mode is enabled. EFF

37、ECT MIX Controls fl FADER/OFF/AUTO (EFFECT MIX selector switch) Use to select the cross fader effect mode. FADER: Selects Effect Mix Fader mode. When this is selected, the Cross fader lever () can be used to control effects and perform cue start and back cue. OFF:Normal mode AUTO:The Effect Mix Auto

38、 mode. When this is selected, the Effect select/start switches (, , ) can be used to control effects, perform cue start and back cue. , , Effect select/start switches Use to select the type of Effect Mix desired (default is ECHO) The switch for the selected function flashes. ECHO switch ZIP switch ROLL switch