Pioneer-DDJSR-djc-sm电路图 维修手册.pdf

《Pioneer-DDJSR-djc-sm电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Pioneer-DDJSR-djc-sm电路图 维修手册.pdf（65页珍藏版）》请在收音机爱好者资料库上搜索。

1、ORDER NO. PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra

2、Road, #04-01, Singapore 159936 PIONEER CORPORATION2013 2013 Printed in Japan DDJ-SR RRV4499 DJ Controller DDJ-SR THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). ModelTypePower RequirementRemarks DDJ-SRCKSUVYXE5DC 5 V (USB-bus power only) DDJ-SRXECN5DC 5 V (USB-bus power only) K-MZV

3、NOV. RadioFans.CN 收音机爱 好者资料库 2DDJ-SR 1234 A B C D E F 1234 SAFETY INFORMATION CONTENTS SAFETY INFORMATION.2 1. SERVICE PRECAUTIONS.3 1.1 NOTES ON SOLDERING .3 1.2 NOTES ON PARTS REPLACEMENT.3 1.3 ABOUT DEMO MODE.4 2. SPECIFICATIONS.5 3. BASIC ITEMS FOR SERVICE.6 3.1 CHECK POINTS AFTER SERVICING.6 3.

4、2 JIGS LIST .6 3.3 PCB LOCATIONS .7 4. BLOCK DIAGRAM.8 4.1 OVERALL WIRING DIAGRAM.8 4.2 OVERALL BLOCK DIAGRAM.10 5. DIAGNOSIS.12 5.1 TROUBLESHOOTING.12 5.2 BASIC OPERATION CHECK USING SERATO DJ.14 6. SERVICE MODE.17 6.1 SERVICE MODE.17 7. DISASSEMBLY.27 8. EACH SETTING AND ADJUSTMENT .33 8.1 NECESSA

5、RY ITEMS TO BE NOTED.33 8.2 UPDATING OF THE FIRMWARE .33 8.3 ITEMS FOR WHICH USER SETTINGS ARE AVAILABLE.35 9. EXPLODED VIEWS AND PARTS LIST.38 9.1 PACKING SECTION .38 9.2 EXTERIOR SECTION.40 10. SCHEMATIC DIAGRAM.44 10.1 MIC and HEADPHONE PCB ASSYS .44 10.2 I/O PCB ASSY .46 10.3 MIXER and CROSS FAD

6、ER PCB ASSYS.48 10.4 PANEL-L and R PCB ASSYS.50 10.5 WAVEFORMS.52 11. PCB CONNECTION DIAGRAM .56 11.1 MIC and HEADPHONE PCB ASSYS .56 11.2 I/O PCB ASSY .58 11.3 MIXER and CROSS FADER PCB ASSYS.60 11.4 PANEL-L and R PCB ASSYS.62 12. PCB PARTS LIST.64 WARNING This product may contain a chemical known

7、to the State of California to cause cancer, or birth defects or other reproductive harm. Health it is not meant for the casual do-it- yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those cove

8、red by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified servi

9、ce technician. RadioFans.CN 收音机爱 好者资料库 3DDJ-SR 5678 5678 A B C D E F 1. SERVICE PRECAUTIONS 1.1 NOTES ON SOLDERING 1.2 NOTES ON PARTS REPLACEMENT For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure to use lead-free solder and a soldering

10、 iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering. Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C. Therefore, for lead-free soldering, the tip temperature of a solderin

11、g iron must be set to around 373 C in general, although the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of the soldering iron. Do NOT use a soldering iron whose tip temperature cannot be controlled. Compared with eutectic solders,

12、 lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. When yo

13、u replacing Front panel, JW ring, it is necessary to remove Front panel. NITTO No. 500 (5 mm 30 mm) NITTO No. 500 (5 mm 40 mm) When detaching the front panel The front panel and the Chassis Assy are secured with 10 pieces of double-back tape at the locations shown in the illustration below. Slowly p

14、eel off the tape, taking care that you will not deform the front panel. When reattaching the front panel 1 Neatly remove any residue of double-back tape from the back of the front panel and the Chassis Assy. 2 Stick 10 pieces (5 mm) of NITTO No. 500 double-back tape to the locations shown in the ill

15、ustration below then remove the paper liner. Note: Even if double-back tape was not used in the initial state, be sure to attach double-back tape when reattaching the front panel. Before securing the front panel to the Chassis Assy with screws, never press on the places where the pieces of double-ba

16、ck tape are attached. Press on the places where the pieces of double-back tape are attached after securing the front panel to the Chassis Assy with screws. Notes: Do not reuse the double-back tape. Put the double-back tape on the Chassis Assy side. NITTO No. 500 (5 mm 40 mm) NITTO No. 500 (5 mm 80 m

17、m) Detachment/Reattachment of the front panel RadioFans.CN 收音机爱 好者资料库 4DDJ-SR 1234 A B C D E F 1234 1.3 ABOUT DEMO MODE Four washers have been added to the screw-mounted parts of the Pad & FSR Plate Assy to solve the problem that a performance pad is only pressed halfway although it is fully pressed

18、. This problem was revealed during production. This emergency measure will be taken care of in the future, but the exact date when the improved products will be produced is not determined yet. At least the first 20,000 products will have the added washers. The initial service parts for the Pad & FSR

19、 Plate Assy will also require attachment of washers. To prevent the washers from not being attached during replacement of the Pad & FSR Plate Assy with the one for service, the Pad & FSR Plate Assy and the washers are to be enclosed in the same package as a kit. The part number of the kit for servic

20、e is GXX1374. When a new Pad & FSR Plate Assy for service is to be reassembled, be sure to attach the enclosed 4 washers to the screw-mounted parts. (See the figure below.) Note on Replacement of the Pad & FSR Plate Assy Pad & FSR Plate Assy Attach the washer. This unit will automatically enter Demo

21、 mode if it is left unoperated for 10 minutes in Normal Operation mode, and a demonstration with LED illumination will start. To cancel this mode, operate any control or button of this unit. To disable Demo mode, change the setting in the settings of Utilities mode 1. (For details, refer to the oper

22、ating instructions.) 5DDJ-SR 5678 5678 A B C D E F 2. SPECIFICATIONS General Main Unit Power supply. DC 5 V Rated current. 500 mA Main unit weight.4.5 kg (9.9 lb) Max. dimensions.553.6 mm (W) 65.3 mm (H) 319.1 mm (D) (21.8 in. (W) 2.6 in. (H) 12.6 in. (D) Tolerable operating temperature.+5 C to +35

23、C Tolerable operating humidity.5 % to 85 % (no condensation) Audio Section Rated output level MASTER OUT 1. 4.2 Vrms MASTER OUT 2. 2.1 Vrms BOOTH. 2.1 Vrms Total harmonic distortion MASTER OUT.0.006 % Frequency characteristic USB, AUX, MIC .20 Hz to 20 kHz S/N ratio (when playing on computer) MASTER

24、 OUT. 101 dB Input impedance AUX .47 k MIC.10 k Output impedance MASTER OUT. 1 k PHONES .32 USB AUDIO.24 bit/Fs : 44.1 kHz Input / Output terminals AUX IN input terminal RCA pin jacks.1 set MIC terminal Phone jack ( 6.3 mm).1 set BOOTH OUT/MASTER OUT2 output terminal RCA pin jacks.1 set MASTER OUT1

25、output terminal Phone jack ( 6.3 mm).1 set PHONES output terminal Stereo phone jack ( 6.3 mm) .1 set Stereo mini phone jack ( 3.5 mm).1 set USB terminal B type .1 set CD-ROM (Installation Disc) USB cable (408-SUB-132) Read Before Use (Important)/Quick Start Guide (DDJ-SR/CKSUVYXE5: 502-DDJSRA-3325A,

26、 502-DDJSRA-3326A) (DDJ-SR/XECN5: 502-DDJSRB-3327) Warranty (for some regions) The included warranty is for the European region. For the North American region, the corresponding information is provided on the last page of both the English and French versions of the “Read Before Use (Important)/Quick

27、 Start Guide”. For the Japanese region, the corresponding information is provided on the last page of the Japanese version of the “Read Before Use (Important)/Quick Start Guide”. Accessories 6DDJ-SR 1234 A B C D E F 1234 3. BASIC ITEMS FOR SERVICE 3.1 CHECK POINTS AFTER SERVICING 3.2 JIGS LIST Distortion Noise Volume too low Volume too high Volume fluctuating Sound interrupted See the table below for the items to be che