Technics-SHDV290-sp-sm 电路图 维修手册.pdf
《Technics-SHDV290-sp-sm 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Technics-SHDV290-sp-sm 电路图 维修手册.pdf(42页珍藏版)》请在收音机爱好者资料库上搜索。
1、ORDER NO.AD0303068C8 Sound Processor SH-DV290EG Colour (S) .Silver Type System: SC-DV290 Because of unique interconnecting cables,when a component requires servise,send or bring in the entire system. Note: Refer to the service manual for Model No. SA-DV290E/EG/EB (ORDER NO.AD0303067C2) for informati
2、on on “ACCESSORIES”and “PACKAGING”. SPECIFICATIONS Specification 1 RadioFans.CN 收音机爱 好者资料库 EQ/SFP section MANUAL GEQ 5-Band EQ Center frequency70/300/1 k/3.15 k/10 kHz Level control2.0, 4.0, 6.0 dB EQ/Space mode 4 modesHEAVY, CLEAR, SOFT, HALL SUPER 3D AI EQ 3 modesAI EQ, SUPER 3D AI 1, SUPER 3D AI
3、2 Pre-amplifier section Input sensitivity/impedance VCR (EXT) 250 mV/15 k VDP (AUX) 250 mV/15 k Output level VCR REC OUT 150 mV/1.5 k DOLBY PRO LOGIC section PRO LOGIC modeSURROUND CENTER modeNORMAL DELAY TIME20 ms (Fixed) AV SURROUND section AV surround mode SUPER SURROUND (MUSIC, MOVIE) DSP CONTRO
4、L section DSP control modeSUPER SOUND EQ CENTER FOCUS VIRTUAL REAR SURROUND MULTI REAR SURROUND SEAT POSITION Spectrum analyzer section Display modeNORMAL, PEAKHOLD, AURORA General Dimensions (WHD)29389270 mm Mass1.5 kg Power SupplyDC10V/ -25V, AC4.6V Power Consumption7W Nots1.Design and specificati
5、ons are subject to change without notice. 2.Dimensions and weight are approximate. 3.Total harmonic distortion is measured by the digital spectrum analyzer. System/SC-DV290 Sound processor: SH-DV290, DVD/ Video CD/ CD changer: SL-DV290, Tuner/ Amplifier: SA-DV290 , Cassette Deck: RS-DV290, Speakers:
6、 Front* (SB- DV290),Center* (SB-PC95),Surround* (SB-PS95) (*Made in MAES.) Manufactured under license from Dolby Laboratories. / “Dolby”,”Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. 2 RadioFans.CN 收音机爱 好者资料库 1. Before Repair This equipment (SH-DV290), which is the compon
7、ent of the system, is supplied with power from the amplifier (SA-DV290).When repairing this equipment or checking operation of the system, be sure to connect the amplifier with it. Power supply and operation check in the state of it as a single equipmenet are impracticable. 2. Operating Instructions
8、 3. Operation Checks and Component Replacement Procedures - This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components. - For reassembly after operation checks or replacement, reverse the respective procedures. Special reassembl
9、y procedures are described only when required. 3.1. Checking for the FL P.C.B. 3 RadioFans.CN 收音机爱 好者资料库 - Check the FL P.C.B. as shown below. 3.2. Checking for the main P.C.B. - Follow the (Step 1) - (Step 3) of item 3.1. 4 - Check the main P.C.B. as shown below. 5 4. Wiring Connection Diagram 5. B
10、lock Diagram 6. To Supply Power Source This unit is designed to operate on power supplied from system connected. When a component requires service, use the system connections to supply power source. For system connections. (Refer to Fig. 1) Fig. 1 7. Schematic Diagram Notes 7.1. Type Illustrations o
11、f ICs, Transistors and Diodes 7.2. Schematic Diagram Notes - This schematic diagram may be modified at any time with development of new technology. Notes: 6 - S601: Display mode (DISPLAY MODE) switch. - S602: DOLBY PRO LOGIC ( PRO LOGIC, OFF/ ON) switch. - S603: Super surround (SUPER SURROUND) switc
12、h . - S604: Super sound EQ (SUPER SOUND EQ) switch . - S605: Center focus (CENTER FOCUS) switch. - S606: Virtual rear surround (VIRTUAL REAR SURROUND) switch. - S607: Multi rear surround (MULTI REAR SURROUND) switch. - S608: Jog control () switch. - S609: Jog control () switch. - S610: Jog control (
13、) switch. - S611: Jog control () switch. - S612: Super 3D AI EQ (SUPER 3D AI EQ) switch. - S613: Seat position (SEAT POSITION) switch. - S614: Joystick (MULTI JOG) switch. - Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) wi
14、th the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internalimpedanceof the DC circuit tester. / No mark: Power on Important safety notice: Components identified by mark have special characteristics impotant for safety. Furthermore, specia
15、l parts which have purpose of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufactures specified parts showninthe parts list. Caution! - IC and LSI are sensitive to static electricity. - Seco
16、ndary trouble can be prevented by taking care during repair. - Cover the parts boxes made of plastics with aluminum foil. - Ground the soldering iron. - Put a conductive mat on the work table. - Do not touch the legs of IC or LSI with the fingers directly. Voltage and signal line 7 : Positive voltag
17、e line : CD Playback signal line : Negative voltage line 8. Schematic Diagram 9. Printed Circuit Board Diagram 10. Terminal Function of ICs 10.1. IC601(C2BBGF000425):System control/FL drive Pin No. MarkI/O / Division Function 1KEY1IOperation key1 signal input terminal 2KEY2IOperation key2 signal inp
18、ut terminal 3SP INIA/D signal input terminal from IC602 4SP AOBand select signal output terminal for IC602 5SP BOBand select signal output terminal for IC602 6SP COBand select signal output terminal for IC602 7SA CSIChip select signal input terminal 8DSP RSTOReset signal output terminal for IC401 9D
19、SP CSOChip select signal output terminal for IC401 10DSP SNSISense signal input terminal from IC401 11DSP ACK IAcknowledge signal input terminal from IC401 12DSP CKOClock signal output terminal for IC401 8 Pin No. MarkI/O / Division Function 13DSP DOOData signal output terminal for IC401 14DSP DIIDa
20、ta signal input terminal for IC401 15JOGAIJOG A signal input terminal 16JOGBIJOG B signal input terminal 17CNVSSIConnected to GND through resistor 18RESETISystem reset signal input terminal 19NC-Not used, open 20NC-Not used, open 21VSS-GND terminal 22XINICeramic oscillator input terminal (f=4MHz) 23
21、XOUTOCeramic oscillator output terminal (f=4MHz) 24VCCIPower supply input terminal 25NC-Not used, open 26NC-Not used, open 27LED CFOOORANGE LED(CENTER FOCUS) signal output terminal 28LED CFGOGREEN LED(CENTER FOCUS) signal output terminal 29BR93 DATA IData signal input terminal from EEPROM 30BR93 CS-
22、Not used, open 31BR93 CK-Not used, open 32SYNCIPower failure detect signal input terminal 33SA REQORequest signal output terminal for Tuner/Amplifier 34SA CKOSerial communication signal output terminal for Tuner/Amplifier 35SA DOOSerial communication signal output terminal for Tuner/Amplifier 36SA D
23、IISerial communication signal input terminal from Tuner/Amplifier 9 Pin No. MarkI/O / Division Function 37LED SSSOLED(SUPER SURROUND)signal output terminal 38LED DPLOLED(DOLBY PRO LOGIC) signal output terminal 39LED SPO OORANGE LED (SEAT POSITION) signal output terminal 40LED SPGOGREEN LED (SEAT POS
24、ITION) signal output terminal 41LED 3DOOORANGE LED (3D ENHANCED SURROUND) signal output terminal 42LED 3DGOGREEN LED (3D ENHANCED SURROUND) signal output terminal 43LED MRO OORANGE LED (MULTI REAR SURROUND) signal output terminal 44LED MRG OGREEN LED (MULTI REAR SURROUND) signal output terminal 45LE
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Technics-SHDV290-sp-sm 电路图 维修手册 Technics SHDV290 sp sm 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf
Fonica PW-7011 - Instrukcja Serwisowa.zip


