Pioneer-DDJErgoV-mix-sm电路图 维修手册.pdf

《Pioneer-DDJErgoV-mix-sm电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Pioneer-DDJErgoV-mix-sm电路图 维修手册.pdf（98页珍藏版）》请在收音机爱好者资料库上搜索。

1、ORDER NO. PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra

2、Road, #04-01, Singapore 159936 PIONEER CORPORATION2011 2011 Printed in Japan DDJ-ERGO-V RRV4269 DJ Controller DDJ-ERGO-V THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). ModelTypePower RequirementRemarks DDJ-ERGO-VXJ5DC 5 V This product is a model for destinations worldwide (except C

3、hina and Korea). It operates only on USB-bus power. No need to use an AC adapter. K-IZV NOV. RadioFans.CN 收音机爱 好者资料库 2DDJ-ERGO-V 1234 A B C D E F 1234 SAFETY INFORMATION WARNING This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproducti

4、ve harm. Health it is not meant for the casual do-it- yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety

5、 and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician. RadioFans.CN 收音机爱 好者资料库 3DDJ-ERGO-V 5678 5678 A B C D E F CONTENT

6、S SAFETY INFORMATION.2 1. SERVICE PRECAUTIONS.4 1.1 NOTES ON SOLDERING.4 1.2 SERVICE NOTICE.4 2. SPECIFICATIONS.5 3. BASIC ITEMS FOR SERVICE .6 3.1 CHECK POINTS AFTER SERVICING .6 3.2 JIGS LIST.6 3.3 PCB LOCATIONS.7 4. BLOCK DIAGRAM .8 4.1 OVERALL WIRING DIAGRAM .8 4.2 OVERALL BLOCK DIAGRAM.10 4.3 P

7、OWER BLOCK DIAGRAM .12 5. DIAGNOSIS .14 5.1 POWER ON SEQUENCE.14 5.2 TROUBLESHOOTING.16 5.3 VOLTAGE MONITORING.25 5.4 ABOUT POWER-SAVING MODE.26 5.5 OPERATION CHECK METHODS, USING VIRTUAL DJ.27 6. SERVICE MODE.30 6.1 HOW TO ENTER EACH MODE .30 6.2 FIRMWARE VERSION CONFIRMATION METHODS.31 6.3 SERVICE

8、 MODE .33 6.4 FACTORY RESET MODE.36 6.5 POWER-SAVING MODE.37 6.6 ERROR DISPLAY.37 6.7 ABOUT THE DEVICE.37 7. DISASSEMBLY .38 8. EACH SETTING AND ADJUSTMENT.43 8.1 NECESSARY ITEMS TO BE NOTED.43 8.2 HOW TO PROGRAM COPY FOR USB CONTROLLER.43 8.3 HOW TO FIRMWARE UPDATE.44 8.4 JOG DIAL ROTATION LOAD ADJ

9、USTMENT.45 9. EXPLODED VIEWS AND PARTS LIST.46 9.1 PACKING SECTION.46 9.2 EXTERIOR SECION.48 9.3 CONTROL PANEL SECTION.50 9.4 JOG SECTION .52 10. SCHEMATIC DIAGRAM.54 10.1 JACK ASSY.54 10.2 IFPW ASSY (1/3) and HPLC ASSY.56 10.3 IFPW ASSY (2/3).58 10.4 IFPW ASSY (3/3).60 10.5 CDJ1 ASSY (1/2).62 10.6

10、CDJ1 ASSY (2/2).64 10.7 HPJK and CRFD ASSYS.66 10.8 CDJ2 ASSY (1/2).67 10.9 CDJ2 ASSY (2/2).68 10.10 JOG1 and JOG2 ASSYS.70 10.11 TCH1 and TCH2 ASSYS.71 10.12 VOLTAGES .72 10.13 WAVEFORMS.73 11. PCB CONNECTION DIAGRAM.78 11.1 JACK ASSY.78 11.2 IFPW, HPLC and HPJK ASSYS .82 11.3 CDJ1 and CRFD ASSYS.8

11、6 11.4 CDJ2 ASSY.90 11.5 JOG1, JOG2, TCH1 and TCH2 ASSYS.94 12. PCB PARTS LIST.95 RadioFans.CN 收音机爱 好者资料库 4DDJ-ERGO-V 1234 A B C D E F 1234 1. SERVICE PRECAUTIONS 1.1 NOTES ON SOLDERING 1.2 SERVICE NOTICE For environmental protection, lead-free solder is used on the printed circuit boards mounted in

12、 this unit. Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering. Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C. Therefore,

13、 for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of the soldering iron. Do NOT use a soldering iron whose tip temper

14、ature cannot be controlled. Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006

15、1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. Voltage Monitoring This unit always monitors for power failure and will shut itself off immediately after an error is detected. A power failure is indicated with flashing of the illumination LED of the channel fader for left side deck (deck A or C)

16、. Other LEDs are unlit after an error is generated. After the unit shuts itself off because of an error, disconnect the USB cable and wait at least 1 minute before turning the unit back on. Repair the unit according to the diagnostic procedures described in “5.3 VOLTAGE MONITORING.” On Point-of-Sale

17、 Demo Mode This product is provided with a Demo mode to be used when displayed on a stand in a shop. Demonstrations with lighting of the LEDs on the control panel are automatically performed even if this product is connected with a PC without the DJ application (VIRTUAL DJ LE) being started on the P

18、C. This mode will be established if no transmission or reception of MIDI signals is performed for 1 minute after the controller is turned ON. After VIRTUAL DJ LE is started, Normal Operation mode will be entered. On the EEPROM on the IFPW ASSY No program has been stored in the EEPROM (IC104) on the

19、IFPW Assy (blank ROM) when it is supplied as a part for service. After the EEPROM is replaced, be sure to copy the program for the USB controller to it. For details, see “8.2 HOW TO PROGRAM COPY FOR USB CONTROLLER.” 5DDJ-ERGO-V 5678 5678 A B C D E F 2. SPECIFICATIONS General Main Unit Power supply.D

20、C 5 V Power consumption.500 mA Main unit weight. 2.9 kg (6.4 lb) Max. dimensions . 554.8 mm (W) 103.2 mm (H) 279.8 mm (D) (21.8 in. (W) 4.1 in. (H) 11 in. (D) Tolerable operating temperature .+5 C to +35 C (+41 F to +95 F) Tolerable operating humidity .5 % to 85 % (no condensation) Audio Section Rated output level MASTER OUT 1.4.2 Vrms MASTER OUT 2.2.1 Vrms Total harmonic distortion MASTER OUT 1.0.006 % MASTER OUT 2.0.006 % Frequency characteristic MASTER OUT 1.