Pioneer-DDJ1000-djc-pl电路图 维修手册.pdf

《Pioneer-DDJ1000-djc-pl电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Pioneer-DDJ1000-djc-pl电路图 维修手册.pdf（95页珍藏版）》请在收音机爱好者资料库上搜索。

1、ORDER NO. 6F, Yokohama i-Mark Place, 4-4-5 Minatomirai, Nishi-ku, Yokohama, Kanagawa 220-0012 JAPAN 2018 Pioneer DJ Corporation DDJ-1000 RRV4682 DJ Controller DDJ-1000 THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). THIS SERVICE MANUAL SHOULD BE USED TOGETHER WITH THE FOLLOWING MANU

2、AL(S). ModelTypePower RequirementRemarks DDJ-1000FWLPWXJAC 110 V to 240 V DDJ-1000SYXJAC 220 V to 240 V DDJ-1000UXJCBAC 120 V DDJ-1000XJCNAC 220 V ModelOrder No.Remarks DDJ-1000RRV4683SCHEMATIC DIAGRAM, PCB CONNECTION DIAGRAM, PCB PARTS LIST K-ZZZ JAN. 2018 RadioFans.CN 收音机爱 好者资料库 2DDJ-1000 1234 A B

3、 C D E F 1234 SAFETY INFORMATION RadioFans.CN 收音机爱 好者资料库 3DDJ-1000 5678 5678 A B C D E F CONTENTS SAFETY INFORMATION.2 1. SERVICE PRECAUTIONS.4 1.1 NOTES ON SOLDERING.4 1.2 NOTES ON REPLACING .4 1.3 SERVICE NOTICE.4 2. SPECIFICATIONS.6 3. BASIC ITEMS FOR SERVICE .7 3.1 CHECK POINTS AFTER SERVICING .

4、7 3.2 JIGS LIST.7 3.3 PCB LOCATIONS.10 4. BLOCK DIAGRAM .12 4.1 OVERALL WIRING DIAGRAM .12 4.2 SIGNAL BLOCK DIAGRAM.13 4.3 POWER BLOCK DIAGRAM .14 4.4 MATRIX INFORMATION.15 5. DIAGNOSIS .17 5.1 STARTUP SEQUENCE .17 5.2 TROUBLESHOOTING.18 5.3 MAIN ASSY DIAGNOSIS METHOD.29 5.4 VOLTAGE MONITORING CIRCU

5、IT.31 5.5 ERROR DISPLAY.32 6. SERVICE MODE.33 6.1 SERVICE MODE .33 6.2 LCD CALIBRATION MODE .50 6.3 CROSSFADER CALIBRATION MODE.51 6.4 ABOUT THE DEVICE.55 7. DISASSEMBLY .56 8. EACH SETTING AND ADJUSTMENT.76 8.1 NECESSARY ITEMS TO BE NOTED.76 8.2 UPDATING OF THE FIRMWARE.77 8.3 ADJUSTMENT METHOD FOR

6、 ROTATION LOAD OF THE JOG DIALS.81 8.4 USER SETABLE ITEMS.84 9. EXPLODED VIEWS AND PARTS LIST.85 9.1 PACKING SECTION.85 9.2 BOTTOM SECTION.87 9.3 CHASSIS SECTION.89 9.4 CONTROL PANEL SECTION (1/2).90 9.5 CONTROL PANEL SECTION (2/2).92 9.6 JOG DIAL SECTION .94 RadioFans.CN 收音机爱 好者资料库 4DDJ-1000 1234 A

7、 B C D E F 1234 1. SERVICE PRECAUTIONS 1.1 NOTES ON SOLDERING 1.2 NOTES ON REPLACING 1.3 SERVICE NOTICE For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure to use lead-free solder and a soldering iron that can meet specifications for use

8、 with lead-free solders for repairs accompanied by reworking of soldering. Do NOT use a soldering iron whose tip temperature cannot be controlled. The part listed below is difficult to replace as a discrete component part. When the part listed in the table is defective, replace whole Assy. Assy Name

9、 Parts that is Difficult to Replace Ref No.FunctionPart No.Remarks MAIN Assy LCDL Assy 12V t 5V RegulatorNJM78M05DL1AIC with heat-padIC501 12V t 1.25V DC/DC ConverterBD9328EFJIC with heat-padIC503 12V t 9V DC/DC ConverterMM3543BHIC with heat-padIC505 7.5V t 5V RegulatorNJM78M05DL1AIC with heat-padIC

10、510 12V t 18V DC/DC ConverterBD9851EFVIC with heat-padIC511 12V t 7.5V DC/DC ConverterBD9851EFVIC with heat-padIC512 7.5V t 5V RegulatorIC513IC with heat-padNJM78M05DL1A 7.5V t 3.3V RegulatorIC514IC with heat-padNJM2886DL3-33 18V t 15V RegulatorIC515, IC516IC with heat-padNJM78M15DL1A -18V t -15V Re

11、gulatorIC517IC with heat-padNJM78M15DL1A DACIC5201IC with heat-padAK4458VN 3.3V t 1.25V RegulatorIC7003IC with heat-padBD00IC0WEFJ-E2 LCDR Assy3.3V t 1.25V RegulatorIC7503IC with heat-padBD00IC0WEFJ-E2 TransistorQ5621, Q5623Transistor with heat-pad2SCR573D3 TransistorQ5622, Q5624Transistor with heat

12、-pad2SAR573D3 DSPIC3001BGAD810K013DZKB400 g About the assembly of the JOG dial display The JOG panel is not coloring to improve the visibility of the LCD. So, internal dust and dirt on the surface are easy to see. Therefore, attention is required when replacing the parts inside the JOG dial (especia

13、lly when replacing TFT LCD (DWX4141). If it gets dirty during work, please remove it before working. In addition, the LCD is performed calibration at the mass production. Therefore, do the same when replacing. g VOLTAGE MONITORING This unit always monitors for power failure and will shut itself off

14、immediately after an error is detected. A power failure is indicated with flashing of the QUANTIZE (WAKE UP) LED (Intervals: 250 ms Light on 125 ms/Light off 125 ms) on the left Deck. All the LEDs other than QUANTIZE (WAKE UP) LED will be light off, and all the switches and VRs will be disabled. Rep

15、air the unit according to the diagnostic procedures described in 5.4 VOLTAGE MONITORING CIRCUIT. g CONFIRMATION OF USER-SETTING This product has user-setting data. Be sure to confirm those data before starting repair, although changing them may not have a large effect. Use the Check Sheet in 8.4 USE

16、R SETABLE ITEMS to which you can transcribe the settings, as required. The settings are stored in FLASH ROM (IC2001) on the MAIN Assy. For details, refer to Changing the settings in the operating instructions. 5DDJ-1000 5678 5678 A B C D E F g How to modify when the rattling of the product is occurr

17、ed Place the 9 points ( ) of the control panel under the block (Height more than 20 mm and Diameter lower than 30 mm is recommended), and attach the chassis part according to the screw tightening order manually. (The block is available at the home center, etc.)(Refer to 7 DISASSEMBLY about the screw

18、 tightening order.) When there is no block, place the whole surface of the control panel to the curing mat, and attach the chassis part according to the screw tightening order manually. Take care not to press the screwdriver strongly to the product in any case. Do not use the electric screwdriver. g

19、 About the Crossfadar Assy A non-contact type fader is used for the Crossfader of this product. So, compared to conventional, it has several tens of times durability. High accuracy is required for assembling the Crossfader, so we will supply the service parts at Assy. Replace it with Cross fader Ser

20、vice Assy (DEA1088). In addition, it is performed calibration at the mass production. Therefore, do the same when replacing. After replacing, you must do the Crossfader calibration (CRF SET) in service mode. Otherwise, it will not start normally. Even when replacing MAIN Assy, it is necessary to do

21、calibration. The settings are stored in FLASH ROM (IC2001) on the MAIN Assy. g About the assembly of the OLED Assy OLED is used in the display of the effect area. Replace the OLED Assy with OLED Assy (Service) (DEA1084). Matrix OEL is stuck to the holder with double-sided tape. If you fail to paste

22、and try to peel off, parts will be broken. So, we will supply the service parts at Assy. g About the repair working of HEADPHONES signal line of MAIN Assy For the noise restraint in specific requirements HEAD PHONES signal line on the MAIN Assy is repaired. The target lot per destination is as follo

23、ws. (The quantity may be changed slightly) SYXJ : 1 to 2000YY UXJCB : 1 to 350CC FWLPWXJ : 1 to 610EQ XJCN : 1 to 20CN 6DDJ-1000 1234 A B C D E F 1234 2. SPECIFICATIONS AC adapter Power requirements.AC 110 V to 240 V, 50 Hz/60 Hz (FWLPWXJ) AC 220 V to 240 V, 50 Hz/60 Hz (SYXJ) AC 120 V, 60 Hz (UXJCB

24、) AC 220 V, 50 Hz (XJCN) Rated current. 0.9 A Rated output. DC 12 V, 3 A Power consumption (standby) .0.4 W General Main Unit Power consumption. DC 12 V, 2 000 mA Main unit weight.6.0 kg (13.4 lb) Max. external dimensions.708 mm (W) 73.4 mm (H) 361.4 mm (D) (27.9 in. (W) 2.9 in. (H) 14.2 in. (D) Tol

25、erable operating temperature. +5 C to +35 C (+41 F to +95 F) Tolerable operating humidity.5 % to 85 % (no condensation) Audio Section Sampling rate .44.1 kHz D/A converter.32-bit A/D converter.24-bit Frequency characteristic USB, LINE, MIC1, MIC2.20 Hz to 20 kHz S/N ratio (rated output, A-WEIGHTED)

26、USB. 112 dB LINE. 96 dB PHONO. 85 dB MIC1. 80 dB MIC2. 80 dB Total harmonic distortion (20 Hz to 20 kHzBW) USB.0.002 % LINE.0.005 % Standard input level / Input impedance LINE.12 dBu/47 k PHONO.52 dBu/47 k MIC1.57 dBu/3.3 k MIC2.57 dBu/3.3 k Standard output level / Load impedance / Output impedance MASTER 1. +6 dBu/10 k/330 or less MASTER 2. +2 dBu/10 k/680 or less BOOTH. +6 dBu/10 k/330 or less PHONES .+8 dBu/32 /10 or less Rat