Panasonic-SAPM4E-cs-sm 电路图 维修手册.pdf
《Panasonic-SAPM4E-cs-sm 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Panasonic-SAPM4E-cs-sm 电路图 维修手册.pdf(68页珍藏版)》请在收音机爱好者资料库上搜索。
1、n Amplifier Section RMS OUTPUT POWER both channel driven simultaneously 10% total harmonic distortion10 W per channel (4 ) Output impedance HEADPHONE16 to 32 Phone jack TerminalStereo, 3.5 mm n FM Tuner Section Frequency range87.50 to 108.00 MHz (50 kHz step) Antenna terminal(s)75 (unbalanced) Prese
2、t stationFM 20 stations AM 15 stations n AM Tuner Section Frequency range522 to 1629 kHz (9 kHz steps) 520 to 1630 kHz (10 kHz steps) n CD Section Disc played 8 cm or 12 cm (1) CD-Audio (CD-DA) (2) CD-R/RW (CD-DA, MP3 formatted disc) (3) MP3 Sampling frequency 2007 Matsushita Electric Industrial Co.
3、 Ltd. All rightsreserved.Unauthorizedcopyingand distribution is a violation of law. SA-PM4E SA-PM4EB SA-PM4EG Colour (S). Silver Type CD44.1 kHz MP332 kHz, 44.1 kHz, 48 kHz Bit rate MP332 kbps to 384 kbps Decoding16/20/24 bit linear Pickup Wavelength785 nm Beam sourceSemiconductor laser Laser powerC
4、LASS 1 Audio output (Disc) Number of channels2 channel Frequency response20 Hz to 20 kHz (+1, -2dB) Wow and flutterBelow measurable limit Digital filter8 fs D/A converterMASH (1 bit DAC) n General Power supplyAC 230 V, 50 Hz (E/EG) AC 230 to 240 V, 50 Hz (EB) Power consumption38 W Dimensions (W x H
5、x D)165 mm x 226 mm x 283 mm Mass2.2 kg Operating temperature range+5 to +35C Operation humidity range5 to 90% RH (no condensation) Powerconsumptioninstandby mode 3.9 W (approx.) CD Stereo System Specification ORDER NO. MD0703001CE RadioFans.CN 收音机爱 好者资料库 Notes : 1. Specifications are subject to cha
6、nge without notices. Mass and dimensions are approximate. 2. Total harmonic distortion is measured by the digital spectrum analyzer. n System : SC-PM4E-SMusic center: SA-PM4E-S 1 Safety Precautions 3 1.1. General Guidelines 3 1.2. Caution for AC Cord 4 1.3. Before Repair and Adjustment 5 1.4. Protec
7、tion Circuitry 5 1.5. Safety Part Information 5 2 Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices 6 3 Precaution of Laser Diode 7 4 Handling Precautions For Traverse Deck 8 5 Handling the Lead free Solder 9 5.1. General description about Lead Free Solder (PbF
8、) 9 6 Accessories 10 7 Operation Procedures 11 7.1. Main Unit Key Buttons Operation 11 7.2. Remote Control Key Buttons Operation 11 7.3. Disc Information 12 8 Self diagnosis and special mode setting 13 8.1. Service Mode Summary Table 13 8.2. Service Mode Table 14 8.3. Error Code Table 15 9 Assemblin
9、g and Disassembling 17 9.1. Caution 17 9.2. Disassembly flow chart 18 9.3. Main Parts Location Diagram 18 9.4. Disassembly of Side Panel L /Serial I/P 17BA1-Motor O/P (1);/Serial I/P 18PRAMVSS33-GND (DRAM) 19PRAMVDD15-Power Supply Voltage (DRAM) 20PRAMVDD33-Power Supply Voltage (+1.6V) 21SPOUTOSpind
10、le Drive O/P 22PCI/O Spindle motor drive O/P signal serial data/Monitoring I/P 23TRVPOTraverse Drive O/P (+ve) 24TRPOTracking Drive O/P (+ve) 25FOPOFocusing Drive O/P (+ve) 26DVSS1-GND 27IOVDD2-Digital Power Supply Voltage 2 (I/O) 28DVDD1-Digital Power Supply Voltage 1 (Built-In) 29SRVMON0-No Connec
11、tion 30SRVMON1-No Connection 31AVSS2-GND 32OSCINIOscillating Input 33CTRCRS-Tracking Cross Comparator 34VREF-+Vref Supply Voltage 35EITracking Input Signal 1 36FITracking Input Signal 2 37DIFocusing Input Signal 4 38BIFocusing Input Signal 2 39CIFocusing Input Signal 3 40AIFocusing Input Signal 1 41
12、PDIAPC Amp I/P 42LDOLaser Drive Current O/P 43CENV-Detection Capacitance Connection terminal 44RFENVORF Envelope O/P 45RFOUTORF Summing Amp O/P 46RFINISGC I/P 47AVDD2-Analog Power Supply voltage 2 (For DSL/PLL) 48ARFDC-AGC Capacitive Connection Terminal 49ARFOUTOAGC Output 50ARFFBIARF Feedback Signa
13、l I/P 51ARFINIAudio RF Signal I/P 52DSLFILoop Filter Terminal (For DSL) Pin No.MarkI/OFunction 53IREFIReference I/P 54PLLF-PLL Loop Filter Terminal (Phase Compare) 55PLLF0-PLL Loop Filter Terminal (Speed Compare) 56OUTLOAudio O/P (LCH) 57AVSS1-GND 58AVDD1-Analog Power Supply Voltage 1 59OUTROAudio O
14、/P (RCH) 60DVSS3-GND3 (Digital Circuit) 61NSRVMONONIServo Motor O/P Enabling 62EXT0-Expansion O/P Port 0 63EXT1-Expansion O/P Port 1 64EXT2-Expansion O/P Port 2 65FLAG-Flag Signal O/P 66TX-Digital Audio Interface O/P signal 67MCLKIMicro-Computer Command Clock I/P 68MDATAIMicro-Computer Data I/P 69ML
15、DIMicro-Computer Load I/P 70STATOStatus Signal O/P 71BLKCKOSubcode Blk Clock 72NRSTOLSI Reset Signal 73DQSYTXT-Pack Signal O/P for CD-Text data 74SMCK-Micro-Computer Clock O/P 75PMCK-IOCNT Serial data O/P (Synchronous O/P) 76DVDD2-Digital Power Supply Voltage 2 (+1.5V) 77IOVDD1-Digital Power Supply
16、Voltage 1 (For I/O) 78DVSS2-GND2 (For Digital Circuit) 79NTEST2ITest Mode Setting (ON:H) 80X2OCrystal Oscillating Circuit O/P 81X1ICrystal Oscillating Circuit I/P 82NTESTITest Mode Setting I/P (ON:H) 83D2OData Sigmal O/P 2 84D1OData Signal O/P 1 85D0OData Signal O/P 0 86D3OData Signal O/P 3 87D4ODat
17、a Signal O/P 4 88D5OData Signal O/P 5 89D6OData Signal O/P 6 90D7OData Signal O/P 7 91D15OData Signal O/P 15 92D14OData Signal O/P 14 93DRVDD-I/O Power Supply Voltage (DRAM) 94D13OData Signal O/P 13 95D12OData Signal O/P 12 96D11OData Signal O/P 11 97D10OData Signal O/P 10 98D9OData Signal O/P 9 99D
18、8OData Signal O/P 8 100SDRCKOClock Signal O/P 18 Terminal Function of ICs 18.1. IC7001 (MN6627954MA) IC SERVO PROCESSOR/DIGITAL SIGNAL PROCESSOR/DIGITAL FILTER D/A CONVERTER 58 SA-PM4E / SA-PM4EB / SA-PM4EG Pin No.MarkI/OFunction 1IN2IMotor Driver Input 2PC2ITurntable Motor Drive Signal (“L”:ON) 3IN
19、1IMotor Drive (1) Input 4PC1-Traverse Motor Drive Signal (“L”): ON) 5-8N.C.-No Connection 9PGND1-Ground Connection (1) for Drive 10PVCC1-Power Supply (1) for Drive 11D1-OMotor Drive (1) reverse - action output 12D1+OMotor Drive (1) forward - action output 13D2-OMotor Drive (2) reverse - action outpu
20、t 14D2+OMotor Drive (2) forward - action output Pin No.MarkI/OFunction 1PCONT1OPower Control Output 1(Pwr Sply,Active HIGH) 2PCONT2-No Connection 3NC-No Connection 4FL_DATA / OCD_SDA IFL Data Output / On Chip Debugger Data 5NC-No Connection 6FL_CLK / OCD_SCL IFL CLK Output / On Chip Debugger Clock 7
21、NC-No Connection 8NC-No Connection 9NC-No Connection 10NC-No Connection 11MMOD-Memory mode selection 12OSC2 (8MHz)OMain Oscillator output (8MHz) 13OSC1 (8MHz)IMain Oscillator input (8MHz) 14VSS-Micom GND 15XI (32KHz)ISlow Oscillator input (32KHz) 16XO (32KHz)OSlow Oscillator output (32KHz) 173.3V-Vo
22、ltage supply 3.3V 18Internal Output (1.8V) -Connect to pin 37 19NRSTI/OMICOM RESET PIN (L: reset) 20NC-No Connection 21NC-No Connection 22NC-No Connection 23NC-No Connection 24DAB_PCONT-DAB module power control 25RMTIRemote Control Input 26NC-No Use 27DAB_DDOW FIC IDAB LSI 24ms synchronization inter
23、rupt 28DAB_IRQIDAB LSI interrupt (currently unused) 29BLKCKICD Subcode Block Clock Input 30VCCDETIVCC Failure Detect Signal (L when AC in) 31CD_MDATAI/OCD LSI Command Data 32STATICD LSI Status Input 33CD_MCLKICD LSI Command Clock 34N.C.-No Connection 35CD_MLDOCD LSI Command Load 36N.C.-No Connection
24、 371.8V-Power Supply (1.8V) 38MUTEAOAnalog MUTE Output(L:MUTE ON) Pin No.MarkI/OFunction 15D3-OMotor Drive (3) reverse - action output 16D3+OMotor Drive (3) forward - action output 17D4-OMotor Drive (4) reverse - action output 18D4+OMotor Drive (4) forward - action output 19PVCC2-Power Supply (2) fo
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Panasonic-SAPM4E-cs-sm 电路图 维修手册 Panasonic SAPM4E cs sm 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


