Panasonic-PMCR17CR16-cs-mec 电路图 维修手册.pdf

《Panasonic-PMCR17CR16-cs-mec 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Panasonic-PMCR17CR16-cs-mec 电路图 维修手册.pdf（8页珍藏版）》请在收音机爱好者资料库上搜索。

1、CD Changer CR16 Mechanism AVC-NBG Any further updates or electrical faults can be accessed on Kbase within Technical Support(search on CR16) 1* Denotes parts that did not require removal in Disassembly so may already be fitted 2* 3* 4* 5* Assembly Page 1/8 Assembly / Adjustment Procedure Phase Mark

2、Phase Mark RadioFans.CN 收音机爱 好者资料库 6 This part is critical Move side plate forward a fraction when fitting. When it clicks into position, move side plate back again. Arrowed tooth must locate in first slot of side plate as shown 7* 8* 9* Hold above gear in position whilst fitting gear below 10 Assem

3、bly Page 2/8 RadioFans.CN 收音机爱 好者资料库 11* Refit screw if it was originally fitted, part number XTBS26+8J Be careful not to over-tighten-this gear is not used in mech operation, only used for the jig tool 12* 13* 14 15 Align the long tooth on the rack (see left) with the half tooth on the gear (see ri

4、ght) Assembly Page 3/8 RadioFans.CN 收音机爱 好者资料库 16 Fit then screw in 17 18* Insert this way round NB Not necessary to remove this lifter gear in disassembly 19 With the left side plate far back, this gear should turn anticlockwise but only slightly clockwise 20* Assembly Page 4/8 Phase Adj. 21 Slot i

5、n as shown on far left, then rotate until phase aligned. Large gear will then catch the pip of the lifter below the lemon gear. 22* 23* 24* 25 The white rack indicated by the red arrows, is shown in the forward position from 26 onwards. This is due to us changing the point of moving side plate forwa

6、rds to simplify repair 26process. This will be rectified once more photos have been taken. This part will naturally move forward when side plate is wound forward in section 34 Assembly Page 5/8 Phase Adj. 27 28 29* 30* 31* 32Align as shown on left Assembly Page 6/8 32 33 At this point bring the side

7、 plate forward using the jig tool until level with front of chassis 34 35 Traverse in down position-lever at rear should be as far back as possible on left side. (See red arrow) Traverse should slot in left side first-may find it easier to use jig tool to move side plate forward further (33). Slow d

8、own as reaching end of travel as complete re-alignment required if it clicks out of position! After slotting in traverse, side plate should be moved back level to front of chassis using jig tool *Marking to the right* Important that this gear does NOT engage with drive rack just above. Pull white ra

9、ck slightly as shown on left until it clicks into position. Assembly Page 7/8 Screw Hook Insert tray drive loading gear in to position and then insert metal shaft down the centre 37 Top lugs on the tray drive loading gear should align horizontally with front of 38mech and trays should be as far forw

10、ard as possible before slotting down. The white gear in the centre of the black plate should move clockwise slightly when the trays are inserted- if it moves anti-clockwise adjust the tray loading drive gear slightly and re-attempt. 39Turning tray drive loading gear 180 degrees may help Slide all tr

11、ays back manually together until front of trays align with front of mech then insert lock lever. 40 We recommend fitting top cover 41before powering up as this provides additional support to the side plate. You are now ready to operate. Please use additional info on CD Test Mode to check operation. Assembly Page 8/8