Panasonic-SAXR55E-avr-sm 电路图 维修手册.pdf
《Panasonic-SAXR55E-avr-sm 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Panasonic-SAXR55E-avr-sm 电路图 维修手册.pdf(130页珍藏版)》请在收音机爱好者资料库上搜索。
1、n AMPLIFIER SECTION Power output (at AC 230-240 V) DIN 1 kHz (T.H.D. 1 %)2 x 100 W (6 ) 20 Hz-20 kHz continuous power output both channels driven 2 x 80 W (6 ) Total harmonic distortion rated power at 20 Hz-20 kHz0.09 % (6 ) Power bandwidth both channels driven, -3 dB4 Hz-88 kHz (6 , 0.9 %) Power ou
2、tput each channel driven (at AC 230-240 V) DIN 1 kHz (T.H.D. 1 %) Front (L/R)100 W (6 ) Center100 W (6 ) Surround (L/R)100 W (6 ) Surround Back (L/R)100 W (6 ) Load impedance Front (L/R) A or B6-16 A and B6-16 BI-WIRE6-16 Center6-16 Surround (L/R)6-16 Surround Back (L/R)6-16 Frequency response CD, T
3、APE, TV, DVD, DVD RECORDER, VCR1, VCR2 4 Hz-88 kHz, 3 dB DVD 6CH4 Hz-44 kHz, 3 dB Input sensitivity and impedance CD, TAPE, TV, DVD/DVD 6CH, DVD RECORDER, VCR1, VCR2 200 mV/22 k 2005 Matsushita Electric Industrial Co. Ltd. All rightsreserved.Unauthorizedcopyingand distribution is a violation of law.
4、 SA-XR55E SA-XR55EB SA-XR55EG Colour (S).Silver Type (K).Black Type (E/EG only) S/N at rated power (6 ) CD, TV, DVD, DVD RECORDER (Digital Input) 90 dB (IHF, A: 103 dB) Tone controls BASS50 Hz, +10 to -10 dB TREBLE20 kHz, +10 to -10 dB Output voltage TAPE, DVD RECORDER200 mV Channel balance (250 Hz-
5、6.3 kHz)1 dB Channel separation55 dB Subwoofer frequency response (-6 dB)7 Hz-200 Hz n FM TUNER SECTION Frequency range87.50-108.00 MHz Sensitivity S/N 30 dB1.5 V/75 S/N 26 dB1.3 V/75 S/N 20 dB1.2 V/75 IHF usable sensitivity (IHF 58)1.5 V/75 IHF 46 dB stereo quieting sensitivity22 V/75 Total harmoni
6、c distortion MONO0.2% STEREO0.3% S/N MONO60 dB STEREO58 dB Frequency response AV Control Receiver Specification ORDER NO. MD0505214C2 RadioFans.CN 收音机爱 好者资料库 20 Hz-15 kHz+1 dB, -2 dB Alternate channel selectivity 400 kHz65 dB Capture ratio1.5 dB Image rejection at 98 MHz40 dB IF rejection at 98 MHz7
7、0 dB Spurious response rejection at 98 MHz70 dB AM suppression50 dB Stereo separation 1 kHz40 dB Carrier leak 19 kHz-30 dB 38 kHz-50 dB Channel balance (250 Hz-6.3 kHz)1.5dB Limiting point1.2 V Bandwidth IF amplifier180 kHz FM demodulator1000 kHz Antenna terminal75 (unbalanced) n AM TUNER SECTION Fr
8、equency range522-1611 kHz (9 kHz step) 530-1620 kHz (10 kHz step) Sensitivity20 V, 330 V/m Selectivity (at 999 kHz)55 dB IF rejection (at 999 kHz)50 dB 1 SAFETY PRECAUTIONS 4 1.1. GENERAL GUIDELINES 4 2 Caution for AC Mains Lead 5 3 Before Repair and Adjustment 6 4 Protection Circuitry 6 5 Handling
9、the Lead-free Solder 6 5.1. About lead free solder (PbF) 6 6 Accessories 7 7 Operating Instructions 8 7.1. Main Unit 8 7.2. Remote Control 9 7.3. Home Theater Connections 10 7.4. Other Connections 15 8 Disassembly and Main Component Replacement Procedures and Operational Check 18 8.1. Disassembly fl
10、ow chart 18 n VIDEO SECTION Output voltage at 1 V input (unbalanced)10.1 Vp-p Maximum input voltage1.5 Vp-p Input/output impedance75 (unbalanced) S-Video InputTV, DVD, DVD RECORDER OutputTV MONITOR Component Video InputTV, DVD, DVD RECORDER OutputTV MONITOR n GENERAL Power supplyAC 230-240 V, 50 Hz
11、Power consumption135 W Dimensions (W H D)430 mm 107.5 mm 394 mm Mass4.6 kg Notes: 1.Specifications are subject to change without notice. Mass and dimensions are approximate. 2.Total harmonic distortion is measured by the digital spectrum analyzer. 8.2. P.C.B. Positions 19 8.3. Disassembly of Top Cab
12、inet. 19 8.4. Checking for the DSP P.C.B. (Side A/B) and Main P.C.B. (Side A). 20 8.5. Disassembly and Checking of Main P.C.B. (Side B) 21 8.6. Disassembly of Tuner Pack and Tuner Extent P.C.B. 21 8.7. Disassembly and Checking of Speaker P.C.B. 22 8.8. Disassembly and Checking of Component Video P.C
13、.B. 22 8.9. Disassembly and Checking of Video Typically the melting point is 50 - 70F (30 - 40C) higher. Please use a high temperature soldering iron. In case of soldering iron with temperature control, please set it to 700 20F (370 10C). Pb free solder will tend to splash when heated too high (abou
14、t 1100F/600C). When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat the soldering points with the Pb free solder until it melts enough. 6 SA-XR55E / SA-XR55EB / SA-XR55EG 6 Accessories Note : Refer to Packaging Materials the power
15、cannot be turned on. Failure in the power circuit system of the unit. This may happen when the direct current electricity is supplied to speaker terminals. Check for the above and replace with new parts if necessary. 9.3. Returning to Normal Display Press the POWER button on the unit to exit the fun
16、ction. The power is turned off. 9.4. Overload/Shutdown Detection intenal Condition It detects OVERLOAD, POWER MALFUNCTION with THRM_DET, SHORT_DET and DC_DET input port. It detects the following condition depending on the input of the port as below table. (H: DC 5V / L: DC 0V) PROTDetection of malfu
17、nctionDisplay and operation SHORT_DETTHRM_DETDC_DET HLHNormal- LLHSpeaker Short, Malfunction of AmplifierOVERLOAD / POWER OFF LHHDetection of THERMAL PROTECTION -LDetection of POWER MALFUNCTION _ _ _ F76 _ _ _ / POWER OFF 9.5. Overload/Thermal Detection Display When overload is detected, automatic P
18、OWER OFF will occur. But if any key on the remote control other than the POWER key is pressed before that (including the HELP key), the scroll display will show SWITCH_OFF_POWER. Then, 1 second after display of message, OVERLOAD will be shown on the scroll display. 9.6. Activating Self Diagnosis Fun
19、ction (Servicing Mode) This mode can be used during servicing. 28 SA-XR55E / SA-XR55EB / SA-XR55EG 1. Plug the AC adapter to the power source. Press and hold down the MULTI CONTROL button and the SPEAKERS A button, and then press the POWER button at the same time. 2. The message, SERVICE appears on
20、the display for three seconds, and then disappears. Refer to Fig. 9.2. Fig. 9.2 3. When the TUNING DOWN button is pressed, the current program filing number (ex. M45_* for MA123_45) appears. The * digit indicates the ROM checksum used for ROM collection, and if the unit is not loaded with ROM, NO ap
21、pears. When the TUNING UP button is pressed, the sub micro computer program filing number (ex. 523_* for MA678_90) appears. The * digit indicates the ROM checksum used for ROM collection, and if the unit is not loaded with ROM, NO appears. 9.7. Analog 6.1 CH Output Check Method When the SUBWOOFER bu
22、tton on the remote controller, the function is switched to Input Inspection Mode, which output analog input signals at L channel of VCR analog input to all channels. 9.8. Returning to Normal Display Press the POWER button on the unit to exit the function. The power is turned off. 9.9. Activating Sel
23、f Diagnosis Function (Doctor Mode) This mode can be used during servicing. 1. Plug the AC adapter to the power source. Press and hold down the MULTI-SOURCE RE-MASTER button and the SPEAKERS A button, and then press the POWER button at the same time. 2. Initialize all the setting and set the frequenc
24、y “99.7MHz” to Tuner. The message, “_DOCTOR_” appears on the display for three seconds, and then disappears. Refer to Fig. 9.3. Fig. 9.3 3. Doctor mode function at some remote control codes as below table. Remote ControlTest Mode Function and settings SelectorSound Modeother settingsVol/Tone CH 1TUN
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Panasonic-SAXR55E-avr-sm 电路图 维修手册 Panasonic SAXR55E avr sm 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


