Nad-C-516-BEE-Service-Manual(1) 电路图 维修手册.pdf

《Nad-C-516-BEE-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Nad-C-516-BEE-Service-Manual(1) 电路图 维修手册.pdf（44页珍藏版）》请在收音机爱好者资料库上搜索。

1、? ? ?6? ? ?6? RadioFans.CN 收音机爱 好者资料库 PRODUCT SAFETY SERVICING GUIDELINES. 1-4 SERVICING PRECAUTIONS . 1-5 * General Servicing Precautions * Insulation checking prodedure * Electrostatically Sensitive Devices SPECIFICATIONS . 1-6 EXPLODED VIEWS CONNECT A 1500 OHM 10 WATT RESISTOR, PARALLELED BY A .1

2、5 MFD, 150V AC TYPE CAPACITOR BETWEEN A KNOWN GOOD EARTH GROUND (WATER PIPE, CONDUIT, ETC.) AND THE EXPOSED METALLIC PARTS, ONE AT A TIME. MEASURE THE AC VOLTAGE ACROSS THE COMBINATION OF 1500 OHM RESISTOR AND .15 MFD CAPACITOR. REVERSE THE AC PLUG AND REPEAT AC VOLTAGE MEASUREMENTS FOR EACH EXPOSED

3、 METALLIC PART. VOLTAGE MEASURE MUST NOT EXCEED 75 VOLTS R.M.S. THIS CORRESPONDS TO 0.5 MILLIAMP AC ANY VALUE EXCEEDING THIS LIMIT CONSTITUTES A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED IMMEDIATELY. SUBJECT : GRAPHIC SYMBOLS SUBJECT : TIPS ON PROPER INSTALLATION 1. NEVER INSTALL ANY PRODUCT IN A

4、 CLOSED-IN RECESS, CUBBYHOLE OR CLOSELY FITTING SHELF SPACE. OVER OR CLOSE TO HEAT DUCT, OR IN THE PATH OF HEATED AIR FLOW. 2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS: OUTDOOR PATIO INSTALLATIONS WHERE DEW IS A FACTOR, NEAR STEAM RADIATORS WHERE STEAM LEAKAGE IS A FACTOR, ETC. 3. AVOID PLACEMENT W

5、HERE DRAPERIES MAY OBSTRUCT REAR VENTING. THE CUSTOMER SHOULD ALSO AVOID THE USE OF DECORATIVE SCARVES OR OTHER COVERINGS WHICH MIGHT OBSTRUCT VENTILATION. 4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMERCAL MOUNTING KIT MUST FOLLOW THE FACTORY APPROVED MOUNTING INSTRUCTIONS A PRODUCT MOUNTED

6、TO A SHELF OR PLATFORM MUST RETAIN ITS ORIGINAL FEET (OR THE EQUIVALENT THICKNESS IN SPACERS) TO PROVIDE ADEQUATE AIR FLOW ACROSS THE BOTTOM, BOLTS OR SCREWS USED FOR FASTENERS MUST NOT TOUCH ANY PARTS OR WIRING. PERFORM LEAKAGE TEST ON CUSTOMIZED INSTALLATIONS. 5. CAUTION CUSTOMERS AGAINST THE MOUN

7、TING OF A PRODUCT ON SLOPING SHELF OR A TILTED POSITION, UNLESS THE PRODUCT IS PROPERLY SECURED. 6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE ON ITS MOUNTING TO THE CART. CAUTION THE CUSTOMER ON THE HAZARDS OF TRYING TO ROLL A CART WITH SMALL CASTERS ACROSS THRESHOLDS OR DEEP PILE CARPETS. 7.

8、CAUTION CUSTOMERS AGAINST THE USE OF A CART OR STAND WHICH HAS NOT BEEN LISTED BY UNDERWRITERS LABORATORIES, INC. FOR USE WITH THEIR SPECIFIC MODEL OF TELEVISION RECEIVER OR GENERICALLY APPROVED FOR USE WITH T.V. S OF THE SAME OR LARGER SCREEN SIZE. 8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION

9、CORDS, EXPLAIN THAT A FOREST OF EXTENSIONS SPROUTING FROM A SINGLE OUTLET CAN LEAD TO DISASTROUS CONSEQUENCES TO HOME AND FAMILY. THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRO

10、DUCT S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK. THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE

11、. PRODUCT SAFETY SERVICING GUIDELINES RadioFans.CN 收音机爱 好者资料库 1-5 SERVICING PRECAUTIONS CAUTION : Bef ore servicing the A/ V Receiver covered by this service data and its supplements and addends, read and f ollow the SAFETY PRECAUTIONS. NOTE : if unf oreseen circumstances create conf lict between th

12、e f ollowing servicing precautions and any of the saf ety precautions in this publication, always f ollow the saf ety precautions. Remember Safety First: General Servicing Precautions 1. Always unplug the A/ V Receiver AC power cord f rom the AC power source bef ore: (1) Removing or reinstalling any

13、 component, circuit board, module, or any other assembly. (2) Disconnecting or reconnecting any internal electrical plug or other electrical connection. (3) Connecting a test substitute in parallel with an electrolytic capacitor. Caution : A wrong part substitution or incorrect polarity installation

14、 of electrolytic capacitors may result in an explosion hazard. 2. Do not spray chemicals on or near this A/ V Receiver or any of its assemblies. 3. Unless specif ied otherwise in this service data, clean electrical contacts by applying an appropriate contact cleaning solution to the contacts with a

15、pipe cleaner, cottontipped swab, or comparable sof t applicator. Unless specif ied otherwise in this service data, lubrication of contacts is not required. 4. Do not def eat any plug/ socket B+ voltage interlocks with which instruments covered by this service manual might be equipped. 5. Do not appl

16、y AC power to this A/ V Receiver and/ or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 6. Always connect test instrument ground lead to the appropriate ground bef ore connecting the test instrument positive lead. Always remove the test instrument

17、ground lead last. Insulation Checking Procedure Disconnect the attachment plug f rom the AC outlet and turn the power on. Connect an insulation resistance meter(500V) to the blades of the attachment plug. The insulation resistance between each blade of the attachment plug and accessible conductive p

18、arts (Note 1) should be more than 1M-ohm. Note 1 : Accessible Conductive Parts including Metal panels, Input terminals, Earphone jacks, etc. Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are cal

19、led Electrostatically Sensitive (ES) Devices. Examples of typical Es devices are integrated circuits and some f ield ef f ect transistors and semiconductor chip components. The f ollowing techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Imme

20、diately bef ore handling any semiconductor component or semiconductor-equipped assembly, drain of f any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed f or potential s

21、hock reasons prior to applying power to the unit under test. 2. Af ter removing an electrical assembly equipped with ES devices, place the assembly on a conductive surf ace such as aluminum f oil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip solderi

22、ng iron to solder or unsolder ES devices. 4. Use only an antistatic solder removal device. Some solder removal devices not classif ied a “anti-static” can generate electrical charges suf f icient to damage ES devices. 5. Do not use f reonpropelled chemicals. These can generate electrical charge suf

23、f icient to damage ES devices. 6. Do not remove a replacement ES device f rom its protective package until immediately bef ore you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive f oam, aluminum f oil, or comparable conductive

24、 material). 7. lmmediately bef ore removing the protective material f rom the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Caution : Be sure no power is applied to the chassis or circuit, and observe all o

25、ther saf ety precautions. 8. Minimize bodily motions when handing unpackaged replacement ES devices. (Normally harmless motion such as the brushing together of your clothes f abric or the lif ting of your f oot f rom a carpeted f loor can generate static electricity suf f icient to damage an ES devi

26、ce.) 1-6 SPECIFICATIONS ELECTRICAL SYSTEMELECTRICAL SYSTEM OUTPUT LEVEL (Vrms) 2Vrms1KHz Full Scale CHANNEL BALANCE(dB) +/-0.5dB(0.13v) FREQUENCY RESPONSE (dB) +/-0.3dB20Hz +/-0.1dB10KHz +/-0.5dB20KHz S/N RATIO (dB) /(A- weight) 110dB CHANNEL SEPARAITION ( 20KHz LPF )95dB1KHz 95dB10KHz DE-EMPHASIS(d

27、B) -20dB 0.2 5KHz -20dB 0.4 16KHz T.H.D () (20KHz LPF)0.005% 100Hz 0.002% 1KHz 0.005% 10KHz 0.005% 20KHz DYNAMIC RANGE / (W/20KHz LPF) 110dB PLAYABILITY 0.9mm INTERRUPTION 0.8mm BLACK DOTS 0.65um FINGER PRINTS 21010um ECCENTRICITY (12cm) 0.5 mm VERTICAL DEVIATION GENERAL ELECTRICAL SPECIFICATIONGENE

28、RAL ELECTRICAL SPECIFICATION Power Requirements AH Version: 120Vac /60Hz C, CT Version: 230Vac /50Hz Power Consumption 0.33Watts Standby 8.8Watts Normal Play 1-7 F10 C516 FASCIA COMPLETE T TITANIUM 1 F10 C516 FASCIA COMPLETE G GRAPHITE 1 1-8 ? F10 C516 FASCIA COMPLETE G GRAPHITE 1 EXPLODED VIEW (C51

29、6BEE) 1-91-10 F10 1.11 NOTES 1-12 NOTES ? ? ? ?. ?2 ?19 ? ? ? ? ? ? ? ? ? ? 2-1 ? ? ? ? 2-2 IC BLOCK DIAGRAMS & PIN DESCRIPTION IC11CS4392D/A CONVERTORIC11CS4392D/A CONVERTOR IC BLOCK DIAGRAMS IC PIN DESCRIPTION 2-3 IC06, IC07, IC15, IC18, IC19 LM1117SXX 1A LDO REGULATOR IC06, IC07, IC15, IC18, IC19

30、 LM1117SXX 1A LDO REGULATOR IC BLOCK DIAGRAMS IC PIN DESCRIPTION 2-4 IC20 LM7808RTRLIC, REGULATOR 1A, 8V IC21, LM7908RTRLIC, REGULATOR 1A, -8V IC20 LM7808RTRLIC, REGULATOR 1A, 8V IC21, LM7908RTRLIC, REGULATOR 1A, -8V IC BLOCK DIAGRAM LM7808RTRL LM7908RTRL 2-5 IC PIN MAP LM7808RTRL LM7908RTRL 2-6 IC1

31、2, IC13 SAA5532DR, OP AMPLIFIERIC12, IC13 SAA5532DR, OP AMPLIFIER IC BLOCK DIAGRAMS IC PIN MAP 2-7 BLOCKDIAGRAM AND PIN DESCRIPTION of ICsBLOCKDIAGRAM AND PIN DESCRIPTION of ICs IC01 TMPM330FWFG (SYSTEM CONTROLLER)IC01 TMPM330FWFG (SYSTEM CONTROLLER) IC BLOCK DIAGRAMS 2-8 IC PIN DESCRIPTION IC02 S80

32、124CLMCJIJT2 (RESET IC)IC02 S80124CLMCJIJT2 (RESET IC) IC BLOCK DIAGRAMS 2-9 RESERVED mt_stby_p NC cd_reseet_p IC PIN DESCRIPTION IC03 SN74ACT04DR HEX INVERTERIC03 SN74ACT04DR HEX INVERTER IC BLOCK DIAGRAMS 2-10 IC PIN DESCRIPTION IC04 IC04 IP4001CRLTF_CN 5-CH MOTOR DRIVER IC BLOCK DIAGRAMS 2-11 IC

33、PIN DESCRIPTION IC05TC94A92FG CD DSP IC05TC94A92FG CD DSP IC BLOCK DIAGRAMS 2-12 IC PIN MAP 2-13 IC07AT24C08N10SC EEPROMIC07AT24C08N10SC EEPROM IC BLOCK DIAGRAMS IC PIN DESCRIPTION 2-19 ? ELECTRICAL TROUBLESHOOTING GUIDE 1. No Power, No Display 2-20 2. Disc Tray Not Opened 2-21 3. Disc is not Played

34、 2-22 4. Disc is playing but No Audio output (Audio Path) 1. BLOCK DIAGRAM 2-232-24 2. WIRING DIAGRAM 2-252-26 POWER PCB CD MECHANISM LOADER BN81 Connector PCB MAIN PCB FRONT PCBS/W PCB CN07 CN09CN08 CN92BN91 CN01 CN05 CN04 CN03 CN41 z 17P FLAT 13P CN42 BN41 5P 17P FLAT 5P 13P6p FRONT PANEL BOTTOM B

35、OARD 13P FLAT6p 6P AC Power Cord (1) (2)(3) (4) (5) (6) (7) (8) 2-15 No.RefPart NumberNo.RefPart Number 1BN81CWB1C913120EN 2 CWC4C4A13B100B10 3BN91 CWB2B905080EN 4 CWC4F2A16A250B10 5 CWB2B005100GG 6 CWB5A906100GG 7 CWC4C4A17B100B10 8BN41 CWB1B905180EN 3. SCHEMATIC DIAGRAM FRONT + TRANSFORMER + AUDIO

36、 PART 2-272-28 C516BEEC: T 315mA L 250V C516BEEAH: T 630mA L 250V FUSE (F801) STBY-LED KEY1 KEY0 GND GND MCU+3.3V VFD-DI VFD-CLK VFD-CE VFD-RST REMO FL- VP FL+ FRONT PCB S T A N D - B Y P O WE R _ O N +5V 7 6 5 4 3 2 1 REVISION SCHEMATIC DIAGRAM SHEET MODEL 1 DRAWING NODESIGNCHECKAPPROVE C516BEE MP

37、JW.RYUBD.JANG JH.PARK H F 8 1H F 8 2 AC_STBY AC_STBY RELAY_I RELAY_O AC_AUDIO AC_AUDIO GND AC_MAIN AC_MAIN VP GNP AC_FILA AC_FILA CLT51009ZE AUDIO PCB MCU+3.3V /RESET_DOWNLOAD UPDATE_RX UPDATE_TX /BOOT MCU SPDIF OPTICAL AUDIO AGND SPDIF GND +5V OPTICAL AGND LEFT RIGHT GND GND GND TRANS PCB (RCA) DOW

38、NLOAD BLUE(ON) Amber(OFF) LOW-ON / HIGH-OFF (3,3V) C301 0.1uF C320 10u/50V R413 10K R414 4.7K C409 0.1uF C410 10u/50V C413 0.1uF C407 1u/50V R412 1K R415 3.3K C411 47P C412 47P C404 47P C405 47P C406 47P R411 220 R410 220 R409 220 C403 100u/16V C402 0.1uF C414 0.1uF C401 0.1uF C400 0.1uF R406 10K R4

39、03 10K R407 1K S304 PAUSE S302 STOP S301 SKIP+ S303 SKIP- S305 OPEN/CLOSE R404 1K R405 1.5K C408 0.1uF 321 VccGNDVOUT RS01 CRVKSM603TH5B R408 1.5K S306 PLAY R401 120 OB D302 R400 1.8K S307 POWER 12567891011121314154950 F2 F2 NC GR1 VDD DIN CLKB CSB RSTB OSCO OSCI VEE GND F1 F1 1G 16 FL41 CFLHCA14SM1

40、9 12345 CN41 54321 BN41 R402 68 1 24 5 6 7 8 9 10 11 12 13 14 1517 16 3 CN42 Q401 RT1P144C Q402 RT1N141C D400 1SS355T 1 2 3 Q400 C3875S 12 D401 CVD1SS355T 12 D402 CVD1SS355T 12 D403 CVD1SS355T 12 D404 CVD1SS355T 12 D405 CVD1SS355T 12 D406 CVD1SS355T 12 D407 CVD1SS355T 12 F801 KJCFC5S C800 4700P 1 4

41、2 3 RY81 CSL1E002ZE 2 46 8 T801 21 CN82 CJP02KA060ZY 1 23 4 5 6 7 8 9 10 11 T802 CLT5M028ZES 13121110987654321 BN81 CWB13 1 2 3 JK91 CJJ4N067Z TX VIN VCC GND 321 JK92 CJSJST1124 1 24 5 6 73 1 2 3 4 5 6 7 CN93 CJP07GB113ZY 1 2 3 JK93 CJJ4M046Z 13 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11 12

42、13 CN92CJP13GA115ZY 54321 1 2 3 4 5 BN91 CWB05 L901 CLZ9R001Z 60 DGND DGND DGNDDGND DGND DGND DGND DGND DGND DGND DGND DGND MCU+3.3V MCU+3.3V MCU+3.3V MCU+3.3V DGND DGND DGND DGND DGND MCU+3.3V +5V +5V SGND SGND 1 WAKEUP 1WAKEUP 1 SW+3.3 1 SW+3.3 RESET MCU KEY1 STBY-LED KEY0 DGND DGND MCU+3.3V VFD-D

43、I VFD-CLK VFD-CE VFD-RST REMO FL- VP FL+ +5V n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c n.c EX_INTERRUPT TMPM33OFWFG(128K) n.c MCU & EEPROM 1 PD6/AN10 2 PD7/AN11 3 AVS

44、S 4 VREFH 5 AVCC 6 PG3/INT4 7 PK2/TB9OUT 8 PJ5/TB7OUT 9 PH4/TB2IN0 10 PH5/TB2IN1 11 PG7/TB8OUT 12 TEST2 13 DVSS 14 DVCC 15 PG4/SO2/SDA2 16 PG5/SI2/SCL2 17 PG6/SCK2 18 TEST1 19 PF7/INT5 20 PE0/TXD0 21 PE1/RXD0 22 PE2/SCLK0 23 PE4/TXD1 24 PE5/RXD1 25 PE6/SCLK1 26 PG0/SO0/SDA0 27 PG1/SI0/SCL0 28 PG2/SCK0 29 PB3 30 PH0/TB0IN0/BOOT 31 PH1/TB0IN0 32 PH2/TB1IN0 33 PF0/TXD2 34 PF1/RXD2 35 PF2/SCLK2 36 PH3/TB1IN1 37 PB4 38 PI0/TB0OUT 39 PJ6/INT6 40 PI1/TB1OUT 41 PB5 42 PI2/TB2OUT 43 PB6 44 PF4/SO1/SDA1 45 PF5/SI1/SCL1 46 PF6/