NAD-T973-pwr-sch 电路图 维修手册.pdf
《NAD-T973-pwr-sch 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《NAD-T973-pwr-sch 电路图 维修手册.pdf(16页珍藏版)》请在收音机爱好者资料库上搜索。
1、Preliminar y ISSUE DATE: September 2005 T 973 Seven Channel Amplifier PRELIMINARY SCHEMATICS updated alignment procedures RadioFans.CN 收音机爱 好者资料库 ALIGNMENT PROCEDURE (T973) A. DC OFFSET VOLTAGE The DC OFFSET between OFFSET Test Point and AGND must be controlled within 0+/-3mV. If its found to be out
2、 of this range, change the TL084BCD to get it meet the requirement. B. IDLING CURRENT The idling current at the final stage of the unit should be set to about 40mA+/-10mA. Adjust RV102 (As marked as “Idling Current ADJ” in the enclosed drawing below) to control the voltage between Idling current Tes
3、t point 1 and 2 to be 8mV +/- 2mV. Preheat the unit for 10 to 15 minutes, and then readjust to 8mV +/- 2mV. (Please note: The idling current must be adjusted when all modules are assembled into the unit.) C. ISC SENSITIVITY Adjust Pot RV104 (as marked as “ISC SENS ADJ” in the below drawing) to get t
4、he voltage across “ISC SENS TEST POINT” and AGND to be 0mV+/-10mV. (Please note that the ISC should be adjusted when all modules are assembled into the unit. Its not possible to get 0V +/-10mV if the modules are not assembled. D. THERMAL SENSE ADJUSTMENT The adjustment should be always done when the
5、 T973 is cool condition. (That means the temperature inside the unit should be almost same as the ambient temperature. Connector P208B that connects the transformer and power board should be removed to avoid that the Idling current to heat up the unit excessively) At ambient temperature of 25 C degr
6、ee and when the unit is just turned on (still in cool condition), adjust the pot RV103 (as marked as “THERMAL SENS ADJ” in the below drawing) to get voltage across the THERMAL TEST POINT and AGND to be 750mV +/-10mV. While the ambient temperature is different, the voltage will vary as well. There is
7、 a relation between the temperature and voltage, that is; if the ambient temperature is 20 degree C, the voltage should be 850mV+/-10mV; if the ambient temperature is 30 degree C, the voltage should be adjusted to 650mV+/-10mV, etc. E. Fan Cut Off Point Adjustment Note: This Fan cut off function doe
8、s not appear on PCB V10.0, V11.0 or MKII version but only appeared on PCB V12.0. Run the unit for all 7 channels at 1 kHz, 4ohms load, and 250mW output. Do this adjustment when the unit heats up, for example; run the unit at all 7 channels at 50W/4ohms for 10 minutes. Then adjust Pot RV201 on power
9、supply board so the voltage at Pin14 of IC203 just changes from negative to positive (to get the fans just start turning). Then turn off the input signal and monitor if fans will stop within 30 seconds, then turn on the input signal again to see if the fans start turning immediately. RadioFans.CN 收音
10、机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 Preliminar y T 973 WIRING DIAGRAM Preliminar y AGND4 -62V_4 +62V_4 AGND4 +62V_4 AGND4 -62V_4 AGND4 PROT6 DGND STBY DGND PROT3 SCLED PROT4 PROT7 SCLED PROT5 +8V PROT1 PROT2 STBY AGND +8V -68V +68V DGND AGND ACOFF +18V FAN2 -18V FAN3 FAN1 +8V AGND6 +62V_3 AGND6 -62V_3
11、AGND6 +62V_3 DGND SCLED SCN_3 SCN_4 SCP_4 +62V_3 SCP_3 -62V_3 -62V_4 +62V_4 -68V SCN_3 +18V ACOFF -18V +68V PROT5 SEN5 SCP_3 -68V SCN_3 +18V ACOFF -18V +68V PROT6 SEN6 SCP_3 -68V SCN_3 +18V ACOFF -18V +68V PROT7 SEN7 SCP_3 AGND6B +62V_3B -62V_3B -62V_3B AGND6B +62V_3B AGND6A +62V_3A -62V_3A -62V_3A
12、AGND6A AGND6A +62V_3A +62V_3 -62V_3 -62V_3 AGND6 AGND6 +62V_3 -68V SCN_4 +18V ACOFF -18V +68V PROT1 SEN1 SCP_4 AGND4A +62V_4A +62V_4A -68V SCN_4 +18V ACOFF -18V +68V PROT2 SEN2 SCP_4 AGND4B +62V_4B -62V_4B AGND4B -68V SCN_4 +18V ACOFF -18V +68V PROT3 SEN3 SCP_4 AGND4 +62V_4 -62V_4 -62V_4 AGND4 +62V_
13、4 +62V_4 -62V_4 -62V_4 AGND4 AGND4 +62V_4 -68V SCN_4 +18V ACOFF -18V +68V PROT4 SEN4 SCP_4 STBY AGND SEN2 SEN3 SEN5 ISCTRIG_6 ISCTRIG_7 SEN1 ISCTRIG_5 ISCTRIG_3 ISCTRIG_2 AGND6B AGND6 FAN1 DGND DGND FAN2 DGND FAN3 +62V_3 +62V_3B +62V_3A -62V_3 -62V_3B -62V_3A AGND6 AGND6B AGND6A ISCTRIG_1ISCTRIG_3IS
14、CTRIG_5ISCTRIG_6ISCTRIG_7 ISCTRIG_1 SEN6 SEN7 DGND ISCTRIG_4 SEN4 AGND4A AGND4A -62V_4A -62V_4A ISCTRIG_2 AGND4B -62V_4B +62V_4B AGND4 ISCTRIG_4 AGND4 -62V_3 AGND6 AGND4A AGND4B AGND4 -62V_4A -62V_4B -62V_4 +62V_4A +62V_4B +62V_4 SCHEMATIC DIAGRAM(AMP CONNECTION) 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9
15、10 10 P603B S10B-PH-SM3-TB P603B S10B-PH-SM3-TB 1 1 2 2 P622 HEADER 2 P622 HEADER 2 BUS606 COPPER STRIP BUS606 COPPER STRIP 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 P608B MOLEX 2145/3215 TOP ENTRY/9PIN P608B MOLEX 2145/3215 TOP ENTRY/9PIN 1 1 2 2 P623 HEADER 2 P623 HEADER 2 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8
16、8 9 9 P615B MOLEX 2145/3215 TOP ENTRY/9PIN P615B MOLEX 2145/3215 TOP ENTRY/9PIN 1 2 3 4 5 6 7 8 9 10 11 12 P618B MOLEX 51021/12PIN/500mm WIRE P618B MOLEX 51021/12PIN/500mm WIRE 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 P609B MOLEX 2145/3215 TOP ENTRY/9PIN P609B MOLEX 2145/3215 TOP ENTRY/9PIN BUS603 COPPER
17、 STRIP BUS603 COPPER STRIP 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 P616B MOLEX 2145/3215 TOP ENTRY/9PIN P616B MOLEX 2145/3215 TOP ENTRY/9PIN 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 P610B MOLEX 2145/3215 TOP ENTRY/9PIN P610B MOLEX 2145/3215 TOP ENTRY/9PIN 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 P601B MOLEX 52
18、207 RIGHT ANGLE/SMT/ZIF/TOP CONTACT STYLE/16PIN P601B MOLEX 52207 RIGHT ANGLE/SMT/ZIF/TOP CONTACT STYLE/16PIN 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 P604B MOLEX 2145/3215 TOP ENTRY/9PIN P604B MOLEX 2145/3215 TOP ENTRY/9PIN BUS601 COPPER STRIP BUS601 COPPER STRIP 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 P619B MO
19、LEX 5145-NCH TOP ENTRY/8PIN P619B MOLEX 5145-NCH TOP ENTRY/8PIN 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 P617B MOLEX 2145/3215 TOP ENTRY/9PIN P617B MOLEX 2145/3215 TOP ENTRY/9PIN 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 P611B MOLEX 2145/3215 TOP ENTRY/9PIN P611B MOLEX 2145/3215 TOP ENTRY/9PIN 1 1 2 2 3 3 4 4
20、5 5 6 6 7 7 8 8 9 9 P605B MOLEX 2145/3215 TOP ENTRY/9PIN P605B MOLEX 2145/3215 TOP ENTRY/9PIN 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 P612B MOLEX 2145/3215 TOP ENTRY/9PIN P612B MOLEX 2145/3215 TOP ENTRY/9PIN 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 P606B MOLEX 2145/3215 TOP ENTRY/9PIN P606B MOLEX 2145/3215 T
21、OP ENTRY/9PIN 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 P602B MOLEX 52207 RIGHT ANGLE/SMT/ZIF/TOP CONTACT STYLE/16PIN P602B MOLEX 52207 RIGHT ANGLE/SMT/ZIF/TOP CONTACT STYLE/16PIN BUS602 COPPER STRIP BUS602 COPPER STRIP 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 P613B MOLEX 2145/3215 TOP ENTRY/9PIN P613B MOLE
22、X 2145/3215 TOP ENTRY/9PIN 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 P607B MOLEX 2145/3215 TOP ENTRY/9PIN P607B MOLEX 2145/3215 TOP ENTRY/9PIN BUS604 COPPER STRIP BUS604 COPPER STRIP 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 P614B MOLEX 2145/3215 TOP ENTRY/9PIN P614B MOLEX 2145/3215 TOP ENTRY/9PIN 1 1 2 2 3 3 4
23、 4 5 5 6 6 7 7 8 8 P620B MOLEX 5145-NCH TOP ENTRY/8PIN P620B MOLEX 5145-NCH TOP ENTRY/8PIN 1 1 2 2 P621B HEADER 2 P621B HEADER 2 BUS605 COPPER STRIP BUS605 COPPER STRIP Preliminar y STBY +62V_4 +68V SEN5 +18V SEN3 STBYLED SEN1 SEN2 -62V_4 SEN3 SEN7 +5VD SEN6 SEN4 SEN5 -18V +8V ISCTRIG1.7 ACOUT RELAY
24、 ACIN ISCTRIG_2 PROT3 -68V FAN1 SEN2 ISCTRIG_7 DGND SCLED STBY AGND4 FAN2 SEN5 +18V +68V ISCTRIG_6 ISCTRIG_7 ISCTRIG_3 SEN7 ISCTRIG_1 AGND4 -18V ACOFF AGND6 +8V SEN3 -68V -62V_3 AGND6 -62V_4 AGND4 FAN3 SEN6 SCLED ISCTRIG_4 FAN1 PROT4 +8V DGND ISCTRIG_4 DGND PROT7 ISCTRIG_1 ISCTRIG_6 +62V_3 PROT2 +62
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAD-T973-pwr-sch 电路图 维修手册 NAD T973 pwr sch 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


