TRIO KENWOOD - W-38 - AM-SW-FM Mono Receiver - Schematic Diagram and Instruction Manual 电路图 维修手册.pdf

《TRIO KENWOOD - W-38 - AM-SW-FM Mono Receiver - Schematic Diagram and Instruction Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《TRIO KENWOOD - W-38 - AM-SW-FM Mono Receiver - Schematic Diagram and Instruction Manual 电路图 维修手册.pdf（12页珍藏版）》请在收音机爱好者资料库上搜索。

1、INSTALLATION AND OPERATING MANUAL DELUXE STEREOPHONIC AMPLIFIER AM- AM/ FM/ SW Tuner- Combination MODEL W-38 DISTRIBUTOR RadioFans.CN 收音机爱 好者资料库 FM STEREO ADAPTER TAPE RECORDER FM ANTENNA MAGNETIC PICKUP INPUT CRYSTAL PICKUP OUTPUT RP CORD SYSTEM JACK RIGHT SPEAKER LEFT SPEAKER STEREO HEADPHONE A. C

2、 CONVENIENCE ANTENNA GROUND TO POWER I SOURCE I. FEATURES OF THE W-38 1. General Stereophonic Amplifier It is a general purpose stereo amplifier capable of FM and shortwave reception enabling you to enjoy all types of broadcasts and recordings. 2. Sufficient Output Output is 14 watts per channel, or

3、 28 watts in total. It is possible, therefore, to reproduce richly the most powerful tones of an orchestra. 3. Direct Current Hum is entirely eliminated with a DC filament supply system adopted to the equalizer circuit. 4. Loudness Control No matter how low you keep the volume, you can enjoy on-the-

4、spot listening by adjusting the Loudness Control. 5. Rumble Filter Irritating low level motor rumbling disturbances can be filtered out with the Rumble Filter. 6. RP-Cord Tape Recorder Terminal The W-38 is equipped with a special socket of the kind agreed to among the major tape recorder manufacture

5、rs (a RP-cord terminal by which recording and reproduction are possible using only one connection) as well as an ordinary terminal. Accordingly, you can freely enjoy high fidelity recording and reproduction with any kind of tape recorder. 7. Magic Eye You can select radio stations quickly and accura

6、tely with the magic eye. 8. Modernistic Design The pleasing modernistic design not seen in previous amplifiers will further brighten the atmosphere of your room. 9. Foster Seeley FM Detector Since the FM detector is a Foster Seeley discriminator, you can enjoy stable and superb high fidelity recepti

7、on. (DIAGRAM 1) 2 RadioFans.CN 收音机爱 好者资料库 II. CONNECTIONS 1. Speaker Connections (In the case of stereo) Unwind the screws of the terminals marked Right Speaker and Left Speaker as shown in Diagram 1, then attach the ends of the Speaker cords to them and tighten. You need not be concerned about ( +)

8、 and (- ). Next, set the IMP SELECT switch to the impedance that corresponds to the impedance of the speaker (the impedance is marked on the speaker cabinet, e.g., 8 ohm or 16 ohm) as in the table below: Speaker Impedance Position of Imp Select Switch 4-8 ohms 8 ohms 9- 16 ohms 16 ohms Check to make

9、 sure the end of the cord is not touching the next terminal. (In the case of speakers) When the speakers are set far apart in a large room, the sound level at the center tends to fall off. In this case, we suggest you add another speaker midway between the two, making the connections as shown in Dia

10、gram 2. By supplementing the volume in this way, you can enjoy a very natural sterephonic reproduction. RIGHT SPEAKER IMP. SELECT LEFT SPEAKER RIGHT SP.PHASE POSITION OF SPEAKER PHASE CENTER (DIAGRAM 2) so- won VOL. CONT. LEFT LEFT SPEAKER 3rd SPEAKER (DIAGRAM 3) RIGHT SPEAKER If you decide to use t

11、hree speakers, first adjust the phasing of the left and right speakers without connecting the middle speaker. See section on Pointers for how to phase) When the speaker phase switch is set at the red mark position, connect the third speaker to the ( +) and (-) terminals of the left and right speaker

12、s, respectively. If the Speaker Phase switch is set at the other position, connect the third speaker to the ( +) terminals of the left and right speakers. NOTE: (1) The potentiometer of 50- 100 ohms is for adjusting the volume of the central speaker so that it will be uniform with the other two spea

13、kers. 3 RadioFans.CN 收音机爱 好者资料库 (2) Place the third speaker exactly mid-way between the left and right speakers as shown in Diagram 3. If the phasing of the central speaker is incorrect, the volume at the center will fall off and you will notice a deterioration in bass sounds. To correct this, inter

14、-change the two lead lines of the central speaker. 2. Antenna and Ground Connections (See Diagram 1) (Antenna for ordinary and shortwave reception) At a place close to the broadcasting station: A vinyl antenna wire of about 2.5 meters in length is provided with the set. As shown in Diagram 4, peel o

15、ff the covering at one end and attach the bare wire to the terminal marked AM. At a place far from the broadcasting station: Since the radio wave grows weak if the station is at a distance, the vinyl wire must either be extended or an antenna set up outside. A special antenna wire is available but a

16、 large vinyl line may be used. Consult your local radio repair man on how to erect an outdoor antenna. Inside a ferro-concrete building: Even if you are located close to the broadcasting station, erect the antenna as far as possible from the wall of the building. W-38 ANTENNA TERMINAL (DIAGRAM 4) (D

17、IAGRAM 5) IMPORTANT Do not place the antenna line near fluorescent lighting which causes disturbance in the form of a buzz. (Antenna for Listening to a FM Broadcast) Connect the FM antenna to G and FM as shown in Diagram 1. Turn the horizontal part of the T -shaped ant.nna towards the direction in w

18、hich you can receive optimum reception and then pin both ends to either the ceiling or walls (See Diagram 6., Make sure the antenna does not sag (Diagram 6) as it will affect the tone quality. This indoor antenna is inadequate where the electric wave is weak. In such a case, set up an outside antenn

19、a and connect with the ANT terminals marked G and FM. You may use the television antenna jointly, but if there is a deterioration in the quality of the image erect separate antennas. See Diagram 4 for joint connection of television antenna. How to Ground You can keep hum down to a mm1mum when reprod

20、ucing a record by grounding the set. As shown in Diagram 7, drive the earth pole into ground where there is as much moisture as possible. Solder the end of a vinyl line to it and connect with the amplifier terminal marked ANT G. If the line is left dangling, it will get in the way so stretch if arou

21、nd 4 VINYL INSULATION TURN PULL COPPER WIRE ANTENNA FEED-IN WIRE AM G FM TELEVISION FEEDER BACK SIDE OF TELEVISION ADJUST TO MOST SUITABLE DIRECTION BY HAND ANTENNA MUST NOT DROOP (DIAGRAM 6) the corners of the room. Do not line it up together with the antenna cord as it will affect sensitivity. NOT

22、E: When you listen to an AM broadcast (medium wave and shortwave) using a short antenna, sensitivity is sharper without ground connection. 3. Player Connections (See Diagram 1) (In the case of stereo pickups) Crystal Pickup: Connect the set of two lead wires from the player to the terminals marked X

23、TAL. Magnetic Pickup: Connect the set of two lead wires from the player to the terminals marked MAG. 4. Tape Recorder Connections (See Diagram 1) (Tape Recorder Equipped with RP Cord) If you use a tape recorder equipped with a RP cord, you can reproduce stereo recording merely by plugging the cord i

24、nto the socket provided for this purpose. (Recording with a tape recorder) Connect the lead lines from the LINE IMPUT terminals of the tape recorder to the terminals marked TAPE REC. In the case of monaural recording, either one (top or bottom) of the terminals may be used. (Playback of tape recorde

25、r) Connect the lead line from the LINE OUTPUT terminals of the tape recorder to the terminals marked AUX on the amplifier. In the case of monaural reproduc tion, either terminals may be used. 5 FM Stereo Broadcast The W -38 provides Receptacles for a FM stereo adaptor so that you may listen to FM st

26、ereo broadcasts by simply connecting the adaptor additionaly with this amplifier. 5 VINYL LINE TYPE W-38 STEREO AMPLIFIER SOLDER TOGETHER GROUND GROUND BAR !COPPER BAR OR 3 mm SIZE WIRE 1 METER LONG) (DIAGRAM 7) III. CONTROLS AND CONNECTION TERMINALS 1. AM RANGE AND POWER SWITCH POWER OFF- Electrici

27、ty turned off. (At all other positions, power is on) SOFT- Listen at this position when there is much disturbance (Medium Wave). HI-FI- Even the high tones are clearly and faithfully reproduced. SW- For shortwave broadcast. 2. VOLUME The sounds of the left and right speakers can be adjusted simultan

28、eously. Turn clockwise to increase volume. 3. LOUDNESS CONTROL OFF- When the volume is relatively high. ON- If adjusted to this position when the volume is low, the bass and treble sounds come out automatically and produce a rich tone that gives you a feeling of actually being at the source of the b

29、roadcast. 4. RUMBLE FILTER OFF - When there is no low frequency disturbance. ON- Irritating low frequency disturbance can be eliminated by turning to this position 5. BASS CONTROL The low level tones of both left and right speakers can be adjusted simultaneously. Turn clockwise to boost. 6. TREBLE C

30、ONTROL The treble tones of both the left and right speakers can be adjusted simultaneously. Turn clockwise to boost. 7. BALANCE CONTROL This knob is for the purpose of balancing the left and right speakers. Turn counter-clockwise to boost the volume of the left speaker and clockwise that of the righ

31、t speaker. 8. FM STABILIZER (FM AFC) OFF- Select FM station with switch at this position. ON- Listen with switch at this position after selecting the station. NOTE- It has no connection with AM or shortwave broadcasts, recording or tape reproduction. 9. SPEAKER SWITCH Employed when a stereo head pho

32、ne is used. OFF- Shuts off the sound from the speaker ON - Turns on the speaker (normal position) 10. SELECTOR SWITCH A switch to select the different sources such as radio, recording, FM stereo, etc. AM-AM2 . . FM-AM2 PHONO AUX . FM MPX For receiving medium wave stereo broadcasts. For listening to

33、FM, ordinary and shortwave broadcasts. For listening to stereo and monaural record perfor mances. For using AUX terminal, or for tape recorder playback. For using a multiplex adaption to listen to a FM stereo broadcast. 6 11. MODE This switch is used to change over from monaural to stereo. LEFT . .

34、. . . . . . . . . Sound entering the left channel input terminal emerges from both speakers. RIGHT . . . . . . . . Sound entering the right channel input terminal emerges from both speakers. STEREO . . . . . . . . Completely separates the two channels for stereo reception. REV . . . . . . . . . . Re

35、verses the left and right channel sounds. 12. TUNING 1 For left channel station selection to listen to medium wave stereo as well as FM broadcasts. 13. TUNING 2 For right channel station selection to listen to medium wave stereo and shortwave broadcasts. 14. LEFT CHANNEL MAGIC EYE When you select th

36、e station with the TUNING 1 knob, see that the magic eye expands to its maximum. 15. RIGHT CHANNEL MAGIC EYE When you select the station with the TUNING 2 knob, see that the magic eye expands to its maximum. 16. SOCKET FOR TAPE RECORDER WITH RP CORD 17. RIGHT SPEAKER TERMINAL (DIAGRAM 8) 18. IMPEDAN

37、CE SWITCH Switch to correspond with speaker impedance. 19. SPEAKER PHASING Use this switch according to instructions given in Pointers section on phasing adjustment. 20. LEFT SPEAKER TERMINAL 21. STEREO HEADPHONE JACK Plug the headphone cord into this jack to listen to stereo broadcast over the head

38、phone. 7 12141513 8123456791011 22. HUM CONTROL Turn until hum is reduced to a minimum according to instruction given in Pointers section on Hum Balancer. 23. ANTENNA, GROUND TERMINALS 24. POWER SOURCE Electricity is taken from here for players and stereo adapter. 25. POWER CORD 26. INPUT TERMINAL P

39、ANEL 27. POWER switch on the power and turn the volume control up almost to maximum. Turn the HUM BALANCER with a screwdriver or coin until hum- an irritating drone- is reduced to minimum. It will suffice to adjust it only once- you need not adjust it again. The hum sometimes decreases depending on

40、the way the amplifier power cord is plugged into the socket. Choose the position with the least hum. 4. HOWLING When the record player is placed directly on top of the speaker case or close by it, the sound from the speaker travels to the player pickup needle and causes howling. It then becomes impo

41、ssible to raise either the volume or boost the bass tones. Adjusting the amplifier will not help since it is not responsible for the howling. In order to avoid howling, keep the player case and speakers as far apart as possible. However, if you are forced to place the player on top of the speaker la

42、y a thick cushion or sponge mat in between. 5. HEATING OF AMPLIFIER The upper surface of the amplifier case reaches a considerable temperature with the elapse of time; but since the W-38 is well designed with this taken into account, you need not worry about it. However, do not place anything on top

43、 of the case thereby blocking the ventilation holes and increasing the heat inside. 6. SPEAKER SWITCH Turn the SPEAKER (See photograph) to OFF position only when you use the headphone. Keep it at ON position at all other times. Caution: Donot raise volume when the switch is in OFF Position with a st

44、ereo headphone disconnected. Otherwise, it is likely to cause a breakdown in your amplifier. 10 VI. SPECIFICATIONS OF THE W-38 Tubes used: Frequency Range: Sensi ti vi ty: Image Ratio: Gain: Tone Control: Rumble Filter: Loudness Control: Output Power: Frequency Response: Equalizer: Residual Noise: S

45、pecial circuits: Input Terminals: Dimensions: Weight: 19 tubes and 1 diode-6BE6 x 2, 6BA6 x 3, 6AQ8 X 2, 6AU6 X 1, 6AL5 X 1, 12AX7 X 3, 6BM8 x 4, 5AR4 x 1, 6DA5 (Magic Eye) x 2, 80 -108Mc. AM; 535 -1605Kc. SW; 3.8- 11M c. FM; 2.6uV /94Mc, AM; 6uV /lMc. SW; 6u V /8Mc. FM; 30dB/94Mc. AM; 46dB/1Mc. Mag

46、; 3mV. Xtal; 36mV. (input required for S/N 20dB quieting) AUX; 225mV. (input required for 9 watt output) SOc/s f+ 10.5dB lOKc +8dB 1.-8dB -8.5dB 50c/s; - 8dB. 20c/s; - 15dB. 50c/s; 15dB. 10Kc; 4dB. (Volume control at - 30dB) 14 watts per channel, (undistorted output 10 watts), or 28 watts in total.

47、(Harmonic Distortion less than 2%) Within 20c/s - 50Kc 0.5dB (output at 500mW) RIAA MAG; 30mV. AUX; 4mV. (volume maximum, tone control flat) FM-AFC, Loudness Control, Rumble Filter, D.C. filament supply Equalizer Circuit, & Stereo Headphone Jack. MAG, XTAL, AUX, TAPE REC, MPX IN, FM OUT, RP (Recording & Playback) CORD SOCKET. 5.6 high x 18 wide x 14.2 deep. 30 lbs. 11