JBL-DVD600-dvd-sm 电路图 维修手册.pdf

《JBL-DVD600-dvd-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《JBL-DVD600-dvd-sm 电路图 维修手册.pdf（57页珍藏版）》请在收音机爱好者资料库上搜索。

1、Model DVD600 5 Disc DVD Changer From the JBL CINEMA ProPack 600 system Preliminary Service Manual SPECIFICATIONS.2 SET-UP GUIDE.3 FRONT PANEL CONTROLS.4 REAR PANEL CONNECTIONS.6 REMOTE CONTROL FUNCTIONS.7 BASIC TROUBLESHOOTING.11 ADVANCED TROUBLESHOOTING.14 DVD600 PCB DRAWINGS.15 DVD600 EXPLODED VIE

2、W.22 EXPLODED/MECHANICAL PARTS LIST23 BLOCK DIAGRAM.24 ELECTRICAL PARTS LIST.27 PACKING/ACCESSORIES.38 DVD600 SCHEMATICS.39 harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 RadioFans.CN 收音机爱 好者资料库 2 TECHNICAL SPECIFICATIONS DVD600 Playback Media:5-inch (12cm) or 3-inch (8cm) DVD-V

3、ideo: Region 1, single or dual sides/layers, linear PCM, Dolby Digital, or DTS CD, CD-RW: Linear PCM Audio Video CD (VCD): MPEG-1 Video, Linear PCM Audio Video Section: Signal format:NTSC Composite Output:1V p-p/75 ohms, sync, negative polarity S Output:Y/Luminance: 1V p-p/75 ohms, sync, negative po

4、larity C/Chrominance: 0.286V p-p Component Outputs:Y: 1V p-p/75 ohms, sync, negative polarity Pr: 0.648V p-p/75 ohms Pb: 0.648V p-p/75 ohms Audio Section: Coaxial Digital Output:0.5V p-p/75 ohms Frequency Response:2Hz to 22kHz, +/ 0.5dB (44.1kHz sampling rate) Dynamic Range:DVD: 105dB (20-bit) CD: 1

5、00dB Channel Separation:90dB THD:0.0035% Signal-to-Noise Ratio:100 dB Wow and Flutter:below measurable limits General: Unit Power Consumption:25W Unit Dimensions:Width: 17.3 inches (440mm) Height: 5.1 inches (130mm) Depth: 16.9 inches (420mm) Unit Weight:14.4 lb (7.6kg) Depth measurement includes kn

6、obs and buttons. Height measurement includes feet and chassis. All features and specifications are subject to change without notice. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Ma

7、crovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibi

8、ted. RadioFans.CN 收音机爱 好者资料库 3 Quick Setup Guide to Using the DVD600 (with the DCR600) The DVD600 can play discs in the following formats: Both 5-inch (12cm) and 3-inch (8cm) discs CD audio discs DTS audio discs CD-RW audio discs DVD movie discs VCD video compact discs However, it cannot play: DVD d

9、iscs with a Region Code other than 1 or All DVD discs using PAL format video DVD-ROM data discs DVD-RAM discs CD-R discs CD-I discs CD-G discs SVCD discs Photo CD discs MP3 audio discs Press the DVD600s Power Switchso that it latches and the Status Indicator turns amber, indicating that the unit is

10、in the Standby mode. Turn the unit on by pressing either the Power On Button b on the remote or the Open/Close Buttonor Play Buttonon the front panel. The Status Indicatorwill turn green. Open the DVD600s drawer, and insert up to 5 discs in the tray locations, using the Disc Skip Buttonto rotate the

11、 carousel to access all locations. Make sure each disc is loaded with the label side up, and that it is seated correctly in its location. When you close the drawer, the DVD600 will automatically start playing the first disc it rec- ognizes, whether it is a CD or DVD disc. However, whichever type of

12、disc is playing, make sure that you have selected DVD as the input source on the DCR600 by pressing d on the remote, or ! on the front panel of the receiver until DVD is indicated. For most discs, the DVD600 and DCR600 will automatically select the correct surround mode. To make sure that audio in t

13、he DTS audio format is correctly processed, you must choose that for- mat as the default in the DVD600s setup menu. Simply stop play of the disc, and enter the setup menu by pressing z on the remote. Use the /Buttons y to scroll down to Digital Audio Output. Press the Set Button to select this optio

14、n, and a screen will pop up, allowing you to choose from PCM, Dolby Digital or DTS outputs. Use the / Buttons yto highlight DTS, then press the Set Buttonto select this choice. You do not need to reset the audio output for other formats. The DCR600 and DVD600 will automat- ically process PCM, Dolby

15、Digital and DTS sig- nals correctly. Press the Menu Button z to exit the menu screen. If you press the Menu Button z while the disc is playing, you can access the discs menu to choose the DTS for- mat there as well. You may wish to experiment with surround modes other than Dolby Digital and DTS usin

16、g the DCR600s functions. Press the Surround Mode Selector t7 to scroll through such choices as Dolby Pro Logic, Dolby 3 Stereo, 5-Channel Stereo, Hall, Theater, VMAx, Logic 7 or Surround Off (Stereo). See page 52 for descriptions of these modes. Press the Stop Buttononce to enter Resume mode, in whi

17、ch play will resume from the point where it was stopped. Pressing the Stop Buttontwice will cause play to resume from the beginning of the disc, or the discs main menu. You may wish to listen to the tracks of a CD, or view the chapters of a DVD, in a different order than they appear on the disc. The

18、 Random function will play all of the tracks on one CD, or all of the chapters on one DVD, in a random order selected by the DVD600. The DVD600 does not randomly play selections from all five discs inserted in its tray, since this might result in the odd experience of alternating among audio tracks

19、and disjointed video selections. Simply press the Random Buttononce to start random play, and press it again to return to standard play, using the discs main menu. The DVD600 offers several variations of Repeat Play: Repeat All discs in the unit once; Repeat 1 Disc until play is manually stopped; Re

20、peat Title on a DVD disc until play is manually stopped; Repeat Track/Chapter on either a CD or DVD disc until play is manually stopped; and Repeat AB, which repeats a programmed selection until play is manually stopped. Press the Repeat Buttonto scroll through the repeat choices. Repeat play can be

21、 stopped by pressing the Repeat Buttonuntil Repeat Off is selected, or by pressing the Stop Buttontwice. Program the Repeat AB function while a disc is playing. Press the Repeat AB Buttonat the start of the passage to be repeated, and press it again at the end of the passage. The passage will contin

22、ue to play until the Stop Buttonis pressed. You can also program play lists of selected tracks or chapters. 1. Select the DVD600 by pressing the DVD Button d, and press the Program Button to bring up the Program Edit Screen. 2. Use the /ykeys to select a disc number, and press either Setor to enter

23、the selection and move to the next option. 3. Use the /ykeys to select a track (for a CD) or title (for a DVD), and press either Setor to enter the selection and move to the next option. If “99” appears, it means the DVD600 has not read the disc yet to determine whether it is a CD or DVD. 4. For DVD

24、s only, use the same procedure to enter a chapter. 5. The next choice is to add the selection to the play list by pressing the Set Button. 6. Repeat Steps 25 to enter up to 25 selections into the play list. 7. Play the list by using the arrow keys to high- light the Play selection, and the Set Butto

25、n to begin play. Press the Stop Button twice to stop playback of the list. To cancel the list, press the Clear Button. 8. To delete a selection, highlight the item to be deleted, press the Set Button, and then use the /ykeys to choose the Delete Button. Press the Set Button again to delete it. Alter

26、natively, highlight the item and press the Clear Buttonto delete it. 9. Insert an entry by highlighting the item in the play list at the point of insertion, pressing the Set Button, and using the key once to select the Insert option. Follow Steps 2 through 5 above to enter the new selection. You may

27、 also edit an entry by pressing the Check Buttontwice to step through the items in a play list. Use the / keys to choose a disc, track or chapter to be edited, and the /ykeys to make a change. This completes the quick setup and operation of your JBL Cinema ProPack 600 system. Additional information

28、is provided in the following sections for those users with additional components, or who wish to make other, more advanced adjustments to their system. 53 47 47 61 46 8D61 56 8D61 55 55 50 61 8D 61 8D 4D51 2D 10D 6D 2D 1D RadioFans.CN 收音机爱 好者资料库 4 DVD600 Front Panel Controls Power Switch: Press to a

29、pply power to the DVD600. When the unit is first turned on, the Status Indicator will turn amber, indicating that it is in Standby mode. To turn the unit on, press the Open/Close Button or Play Button, or use the remote control to select DVD d, and then power the unit on b. Status Indicator: When th

30、e DVD600 is in the On mode, this indicator will glow green. When the unit is in Standby, the indicator will glow amber. Disc Tray: Holds up to five DVD or CD discs that can be played one at a time in the DVD600. Disc Skip: Press to change the disc being played. Each press of the button will move the

31、 tray forward to the next occupied position in the tray, skipping over the empty disc positions. Search Forward/Reverse: Press to move forward or backward through a disc at one of four speeds. Each press and release will increase the search speed, as indicated in the on-screen display. Once you have

32、 selected the desired speed, release the button and the disc will continue to search at fast speed. To resume normal playback speed, press the Play button. Open/Close Button: Press to open or close the Disc Tray . Skip Forward/Reverse: Press to move forward or backward through the music tracks or ch

33、apters on a disc. Stop: Press once to place the disc in the Resume mode, which means that playback will stop, but (as long as the tray is not opened or the disc changed) DVD playback will continue from the same point on the disc when the Play button is pressed again. Resume will also work if the uni

34、t was turned off. To stop a disc and have play start from the beginning, press the button twice. Pause: Press to momentarily pause playback. To resume playback, press the button again, or press the Play Button . If a DVD is playing, action will freeze and a still picture will be displayed when the b

35、utton is pressed. Play: Press to begin playback of a disc, or to resume playback after the Pause Button has been pressed. Direct Access Buttons: Press one of these buttons to play any of the five discs loaded in the Disc Tray. Information Display: This display con- tains a variety of indicators that

36、 provide infor- mation about the status of the DVD600 and the disc currently playing. Display Dim: Press this button to adjust the brightness of the Information Display by 50% or to turn the display off completely in the following order: FULL BRIGHTNESS HALF BRIGHTNESS OFF FULL BRIGHTNESS. Remote Se

37、nsor: The sensor that receives the infrared commands from the remote control is behind this area. Do not cover or obscure this part of the front panel, in order to avoid a malfunction with the remote. 14D 13D 12D 11D 9D 10D 10D 9D 8D 7D 3D 6D 5D 4D 3D 2D 10D6D 2D 1D 231 5 search play disc skip skip

38、open/close pause stop 4Dimmer power RESUME TITLE RANDOM CHAPTER REPEAT TRACK 1ALL HOUR DISCA B MIN PROG. INTROSEC DVD CD ? 1 2 34 5 DISC VCD 5 DVD600 Front Panel Information Display Disc Type: Lights to show the type of disc currently being played. Disc Number: Shows if a disc is loaded in a tray po

39、sition. The indicator for the disc in play flashes. Note that if a disc is added to, or removed from, the tray while a disc is playing, the indicator will not show the change until all discs are cycled. Title: Shows the DVD title number cur- rently playing. Chapter/Track Number: Shows the current ch

40、apter (DVD) or current track number (CD). Program Time: Shows the running time of a DVD or current track time, time remaining in the current track, or the total remaining time of a CD. NOTE: The Program Time Indicators will also display text messages about the DVD600s sta- tus, including Reading whe

41、n a disc is loading, Bye when the unit is turned off, and Disc Error when a disc not compatible with the DVD600 is put into the play position. Intro: Lights when the Intro Scan function is active. Program: Lights during programming. Repeat: Lights to indicate any of the Repeat modes. Random: Lights

42、when the unit is in the Random Play mode. Resume: Lights when the Stop button has been pressed once to put the unit in the Resume mode. Playback Mode: Lights to show the cur- rent playback mode: Lights when a disc is playing in the Normal mode. Lights when the disc is in the Fast Search Forward mode

43、. For DVDs, when both triangles glow steadily, the disc plays at 2x normal speed. When the right triangle is flashing, the disc plays at 4x normal speed. When the left triangle is flashing, the disc plays at 8x normal speed. When both triangles are flashing, the disc plays at 16x normal speed. For C

44、Ds, only the first three Fast Search modes are available. Lights when the disc is paused. Lights when the disc is in the Fast Search Reverse mode. For DVDs, when both triangles glow steadily, the disc plays at 2x normal speed. When the left triangle is flashing, the disc plays at 4x normal speed. Wh

45、en the right triangle is playing, the disc plays at 8x normal speed. When both triangles are flashing, the disc plays at 16x normal speed. For CDs, only the first three Fast Search modes are available. Parental Lock Indicator: This indicator lights when the parental-lock system is engaged in order t

46、o prevent anyone from changing the rating level without a code. RESUME TITLE RANDOM CHAPTER REPEAT TRACK 1ALL HOUR DISCA B MIN PROG. INTROSEC DVD CD ? 1 2 34 5 DISC VCD 6 Coaxial Digital Output: Connect this jack to the coaxial digital input of an A/V receiver or surround processor for Dolby Digital

47、, DTS or PCM audio playback. NOTE: The coaxial digital output should only be connected to a digital input. Even though it is the same RCA-type connector as standard analog audio connections, DO NOT connect it to a conventional analog input jack. Composite Video Output: Connect this jack to the video

48、 input on a television or video projector, or to a video input on an A/V receiver or processor if you are using that type of device for video input switching. S-Video Output: Connect this jack to the S-Video input on a television or video projector, or to an S-Video input on an A/V receiver or proce

49、ssor if you are using that type of device for S-Video input switching. Component Video Outputs: If your TV or video projector has component video inputs, you may connect these output jacks to the set for the highest video quality available. Note that the component video inputs may be labeled as Y/Pr/Pb or Y/Cr/Cb but, for connec- tion purposes, they are the same. The outputs of these jacks should NOT be connected to a standard composite video input. Remote Control Output: Connect this