Infinity-BU2-sub-sm 电路图 维修手册.pdf
《Infinity-BU2-sub-sm 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Infinity-BU2-sub-sm 电路图 维修手册.pdf(18页珍藏版)》请在收音机爱好者资料库上搜索。
1、BU2 Powered Subwoofer A Harman International Company Part No.: 1112-BU2 11/98 Technical ManualTechnical Manual INFINITY SYSTEMS INC. 250 Crossways Park Drive Woodbury, New York 11797 RadioFans.CN 收音机爱 好者资料库 1 Powered SubwooferBU2 BU2 SPECIFICATIONS Driver.12 Woofer Nominal Impedance .4 Enclosure Des
2、ign.Tuned Port Amplifier Power.100 watts RMS Frequency Response.30Hz - 150Hz ( 3dB) Crossover Frequency.50 to 200 Hz Continuously Variable Inputs Line Level .RCA jacks High Level .(Speaker) Input terminals Outputs.Full range Speaker Sensitivity Low Level .70mV High level .1.7V Input Impedance Low Le
3、vel .12K High level .4.7K Auto-Off Delay.8 minutes Dimensions Inches.14 x 14 x 14 Metric.36.8 x 36.8 x 36.8cm plus 1 (32mm) for feet Shipping Weight .43 lbs/19.5 Kg. Occasional refinements may be made to existing products without notice, but will always meet or exceed original specifications unless
4、otherwise stated. TABLE OF CONTENTS BU2 SPECIFICATIONS .1 TABLE OF CONTENTS.1 BU2 CONTROLS AND THEIR FUNCTION .2 BU2 TEST PROCEDURE.3 BLOCK DIAGRAM .4 BU2 CABINET EXPLODED VIEW .5 AMPLIFIER EXPLODED VIEW.6 BU2 MECHANICAL PARTS LIST .7 BU2 ELECTRICAL PARTS LISTS .8 BU2 PACKAGING EXPLODED VIEW .10 INT
5、EGRATED CIRCUIT DIAGRAMS.11 PCB (TOP VIEW, component side).12 PCB (BOTTOM VIEW, solder side).13 PREAMP/CROSSOVER SCHEMATIC 120V.14 AMPLIFIER SCHEMATIC 120V .15 PREAMP/CROSSOVER SCHEMATIC 230V.16 AMPLIFIER SCHEMATIC 230V .17 THIS MANUAL IS FOR THE BU2 REVISION WITHOUT AN EXTERNAL POWER SWITCH (120v O
6、nly - 230v version has a power switch) RadioFans.CN 收音机爱 好者资料库 2 Powered SubwooferBU2 BU2 CONTROLS AND THEIR FUNCTION LOW LEVEL INPUT R L L L R R POWER 50 60 200 120 80 180 VOLUME CONTROL WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION
7、RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: SHOCK HAZARD-DO NOTOPEN. AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR. NOT SUITABLE FOR IN-WALL MOUNTING 120V60Hz 230W MODEL BU2 ONREVOFFNOM STANDBY RED HIGH LEVEL INPUT HIGH LEVEL OUTPUT FREQUENCY Hz AUTO POWER PHASE MINMAX LISTED 773L P/N WF-100i AUDIO
8、EQUIPMENT POWER ON OFF 1 2 5 6 7 8 4 3 230v ONLY 1. Auto Power - This Auto On/Off switch controls whether the BU2s Automatic turn-on circuit is active. When this switch is ON, the BU2 will turn itself on, indicated by a green LED, when it is plugged in and receiving a signal. When the BU2 has not re
9、ceived a signal for 8 - 10 minutes, the unit will revert to the STANDBY mode, indicated by a red LED. When this switch is OFF, the unit switches to the STANDBY mode and will stay OFF, regardless of input signal. THIS IS NOT A TRUE AC POWER SWITCH AS IT DOES NOT DISCONNECT THE AMPLIFIER FROM THE AC L
10、INE. 2. Standby LED - The LED will light green when the unit is plugged in and is receiving signal. When in standby mode (when the Auto mode is active but the subwoofer is receiving no signal) the LED is red. 3. High Level Inputs - These High Level Inputs are for receivers that do not have line-leve
11、l “pre-amp out” or “subwoofer out” jacks. When a pair of main or satellite speakers are attached to the OUTPUT terminals, they are driven the full range of frequencies as generated by the music source (receiver, amplifier, etc.) 4. Low Level Input - These left and right Line Level Inputs are normall
12、y used when the receiver/ processor has line-level “pre-amp out ” or “subwoofer out” jacks. If a single cable mono or subwoofer source is connected to the BU2, a Y-cable must be connected to the subwoofer for full output. 5. Frequency - The Frequency adjustment determines the upper corner roll-off p
13、oint for the BU2. 6. Phase - This controls the switch from the reverse to normal in audio signal polarity. 7. Volume Control - This controls the volume level of the subwoofer. 8. AC Power - This switch, present on the 230v version only, connects the AC line voltage to the BU2; normally it is left in
14、 the ON position. RadioFans.CN 收音机爱 好者资料库 TEST PROCEDURE Equipment needed: ?Function/signal generator/sweep generator ?Integrated Amplifier ?Multimeter ?Cables - line level (RCA) and speaker cables General FunctionUUT = Unit Under Test 1.Connect both right and left line level inputs (RCA) to signal
15、generator and UUT. Use Y-cable if necessary from mono source. VOLUME control should be full counterclockwise. 2.Turn on generator, adjust to 50mV, 50 Hz. 3.Plug in UUT; red LED should be ON. Turn VOLUME control full clockwise. 4.LED should turn Green; immediate bass response should be heard and felt
16、 from port tube opening. 5.Turn off generator, turn VOLUME control fully counterclockwise, disconnect RCA cables. 6.Connect one pair of speaker cables to either high level input terminal on UUT. Cables should be connected to an integrated amplifier fed by the signal generator. 7.Turn on generator an
17、d adjust so that speaker level output is 2.0V, 50 Hz. Turn VOLUME control full clockwise. 8.Green LED should light, immediate bass response should be heard and felt from port tube opening. Sweep Function 1.Follow steps 1 - 4 above, using a sweep generator as a signal source. 2.Sweep generator from 2
18、0Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove driver and test. Driver Function 1.Remove driver from cabinet; detach + and - wire clips. 2.Check DC resistance of driver; it should be 3.3 ohms. 3.Connect a p
19、air of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4.Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises. 3 Po
20、wered SubwooferBU2 BU2 TEST PROCEDURE 4 Powered SubwooferBU2 BU2 BLOCK DIAGRAM (for 120v & 230v versions) 5 Powered SubwooferBU2 BU2 CABINET EXPLODED VIEW 6 Powered SubwooferBU2 AMPLIFIER EXPLODED VIEW BU2 Amplifier Exploded View E E D D C C B B A A 7 7 6 6 5 5 4 4 3 3 2 2 1 1 2 17 1 3 4 5 6 13 15 2
21、213 18 19 20 14 24 23 16 16 7 8 10 11 12 21 11 11 9 2 7 Powered SubwooferBU2 BU2 MECHANICAL PARTS LISTS Ref.#Part #DescriptionQty 1XX1342GASKET 1 OF 44 2XX1250Strain Relief SPT-1 Black2 3XX1275Plastic Cover For Inf. Bu-1(2)1 4NU1049Nut 8-32 x 1/4 Hex Keps Sink F4 (XFORMER) 5MI1211POWER TRANSFORMER B
22、U-21 6BR1538FRONT PLATE BU-21 7SW1082THERMOSWITCH 60 DEG C PANEL1 MOUNTED FASTON TERM (FRONT PLATE) 8HA1132HARNESS AC CORD BU-1/BU-21 (FRONT PLATE) 9XX1343KNOB BLACK W-POSITION INDICATOR2 (CUSTOM) (POT.) 10HS1171HEATSINK BU-2 (FRONT PLATE)1 11SC1284Screw 4-40X 3/8 TATTITE, PAN PHIL9 HEAD, BLACK ZINC
23、 FIN (HEATSINK-FRONT PLATE) 12BR1544BRACKET FOR HEATSINK BU-21 13BR1395Bracket Pwr Support Bass5502 14SP1082SPONGE W/ADHESIVE L=1/4 W=1/42 T=3/16 (TO-92) 15SP1073Sil Pad TO-3P 1.0 x 0.750 (POWER3 XTORS TO-218 1X, TO-220 2X) 16SC1194Screw 6-32x3/8 Tapt-Thr Hex Washr2 (PC BOARD BRACKET) 17HA1218SPK HA
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Infinity-BU2-sub-sm 电路图 维修手册 Infinity BU2 sub sm 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


