GallienKrueger-MBSeries-pwr-sm 电路图 维修手册.pdf

《GallienKrueger-MBSeries-pwr-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《GallienKrueger-MBSeries-pwr-sm 电路图 维修手册.pdf（21页珍藏版）》请在收音机爱好者资料库上搜索。

1、 Service Manual Micro Bass Series Downloaded from www.M manuals search engine RadioFans.CN 收音机爱 好者资料库 ? ? ? ? ? ?!? ?#?$? Downloaded from www.M manuals search engine RadioFans.CN 收音机爱 好者资料库 Downloaded from www.M manuals search engine RadioFans.CN 收音机爱 好者资料库 Downloaded from www.M manuals search engin

2、e Downloaded from www.M manuals search engine Downloaded from www.M manuals search engine Downloaded from www.M manuals search engine MB150S Preamp Turn-On Procedure GK Document # 420-0061-A / Preamp Board #206-0061-C Model- MB150S- All Options Revised 7/26/99 SETUP 1)Power switch off- connect power

3、 cord. 2)Connect “power” 3-pin connector to P1 on MB-S board so that it clicks into position. Colors should read (L-R)- black, violet, brown. (P1 is furthest from front of panel.) 3)Connect “signal” 3-pin connector to P2 on MB-S board. Colors should read (L-R)- white, black and red. (P2 is closer to

4、 front of panel.) 4)Connect either output to Load Box (Load A). 5)Resistance loads open (switch in center). 6)Load Box to scope-B and AC-VM. 7)Set scope switch on Load Box to look at Load A(down). 8)Probe (1:1) to scope-A and DVM. No Gnd lead required. 9)Connect oscillator to input. 10) Set oscillat

5、or on 100Hz sine wave 0.5 Vrms (-6dBV). 11) DVM on 20V range. 12) AC voltmeter on 30V range. 13) Scope-A on 5V/cm, scope-B on 10V/cm. 14) Scope sweep on 2ms/cm, scope trigger on A. On MB-S Preamp set: 15) Output level to 0, switches out. 16) Contour, hi-boost to 0. 17) Volume, tones and limiter leve

6、l to 10. POWER AND LIMITER TEST 1)Turn on power switch. 2)Power LED on front panel should be lit. 3)Look at output- should be a clean sine wave w/ no crossover distortion, and be about 1.2Vp-p. 4)Flip scope switch to look at Load B (up) and see it is also 1.2Vp-p w/ no crossover distortion. 5)For Co

7、mbo units: Switch internal speaker on, make sure disconnected. Switch off. 6)Change scope to 10V/cm scale. 7)Increase oscillator output to 160mVrms (-16dBV). Output = 14Vrms. 8)Engage limiter. Output falls to 11Vrms. 9)Decrease limiter level to 0. Output falls to 7.5Vrms. 10) Increase output level t

8、o 10. Output goes to 10Vrms. 11) Disengage limiter. Output hits rails hard. 12) Switch both loads to 4 ohms- signal should clip on top and bottom and then shut off after a few seconds. (May have to add 8.2 ohms resistance). 13) Remove loads (switches to center) and set output level to 12 oclock. 14)

9、 Turn unit off and then on again. Note how long it takes before output reappears on scope- should be no more than 2-3 seconds. INPUT SET-UP AND SYSTEM GAIN TEST 1)Turn on power switch- power LED only should light. 2)Look at U1-U7 with probe. Adjust R13 (1K trim pot) so the signal hits the rails even

10、ly on both sides. Signal should be about 22 V p-p. 3)Engage 10dB switch. Signal becomes 1.7Vrms. 4)Direct Out pins 2 Treble to 0- Fig. 3 B)Hi-mid to 10- Fig. 4; Hi-mid to 0- Fig. 5 C)Lo-mid to 10- Fig. 6; Lo-mid to 0- Fig. 7 D) Bass to 10: Fig. 8; Bass to 0- Fig. 9 VOICING FILTERS TEST 1)Engage low-

11、cut switch- compare to Fig. 10. Disengage. 2)Increase contour to 10- compare output to Fig. 11. Reset to 0. 3)Increase hi- boost to 10- compare output to Fig. 12. Reset to 0. NOISE TEST 1)Remove oscillator input. 2)Turn large front panel knobs to 10, small knobs to 0, switches out. 3)Connect speaker

12、 to output and listen for noise, sound should be clean, no crackling or distortion. 4)Change AC voltmeter range to 0.1V. 5)Noise should measure less than 60mV. 6)AC voltmeter to 0.3V range. 7)Engage low-cut, hi-boost and contour to 10. Noise 300 mVrms. RETURN KNOBS TO ZERO- READY FOR BURN-IN. Downlo

13、aded from www.M manuals search engine Downloaded from www.M manuals search engine Downloaded from www.M manuals search engine MB150E Preamp Turn-On Procedure GK Document #: 420-0087-A / Preamp Board # 206-0087-B Model #s: MB150E- All options Rev. 7/27/99 SETUP 1)Power switch off - connect power cord

14、. 2)Connect “power” 3-pin connector from power amp to connector P1 on MB-E board. The colors should read (bottom-top): black, violet, and brown. (P1 is closest to front of panel.) 3)Connect “signal” 3-pin connector from power amp to connector P2 on MB-E board. These colors should read (bottom-top):

15、white, black and red. (P2 is furthest from front of panel). Colors should be clearly marked on board. 4)Connect either output to load box (Load A). 5)Resistance loads open (switch in center). 6)Load box to scope-B and AC-VM. 7)Set scope switch on load box to look at Load-A (down). 8)Probe (1:1) to s

16、cope-A and DVM. (No GND lead required.) 9)Connect oscillator to input. 10) Set oscillator on 100Hz sine wave 0.5Vrms. 11) DVM on 20V (AC) range. 12) AC voltmeter on 30V range. 13) Scope-A on 5V/cm, scope-B on 10V/cm. 14) Scope sweep on 1ms/cm, scope trigger on A. 15) Output level to 0, switches out.

17、 16) Contour, hi-boost, boost to 0. 17) Volume, tones, and limiter to 10. POWER AND LIMITER TEST 1)Turn on power switch. 2)Disengage switches on RF2 so that LEDs are off. Only the power LED should be lit. 3)Look at output- should be clean sine wave w/ no crossover distortion, and be about 0.6Vp-p. 4

18、)For Combo units: switch on internal speaker and make sure its connected. Turn off. 5)Change scope to 10V/cm scale. 6)Increase oscillator output to 160mVrms (-16dBV). Output = 21Vrms. 7)Engage limiter. Output falls to 14Vrms. 8)Decrease limiter level to 0. Output falls to 8.5Vrms. 9)Increase output

19、level to 10. Output goes to 11.5Vrms. 10) Disengage limiter. Output should hit rails hard. 11) Switch both loads to 4 ohms- signal should clip on top and bottom, and then shut off after a few seconds. (May have to add 8.2 ohms resistance.) 12) Remove loads (switches to center) and set output levels

20、to 12 oclock. 13) Turn unit off and then on again. Note how long it takes before output appears on scope- should be no more than 2-3 seconds. INPUT SET-UP AND SYSTEM GAIN TEST 1)Turn on power switch- power LED only should light. 2)Look at U1-1 with probe. Adjust R13 (1K trim pot) so signal hits the

21、rails evenly on both side. Signal should be about 22Vp-p. 3)Engage 10dB switch. U1-1 becomes 1.7Vrms. Disengage 10dB switch. 4)Scope trigger to B. Set oscillator to 46dBV (5mVrms). 5)Output level to 10. Output should be about 8Vrms. 6)Engage limiter. Limiter LED should light. (Output raises slightly

22、.) 7)Decrease limiter to 0. Output drops to 6Vrms. Downloaded from www.M manuals search engine INPUT SET-UP AND SYSTEM GAIN TEST(contd.) 8)Disengage limiter. 9)Look at tip of headphone output jack (J4). Output should be about 1Vrms at this point. 10) Repeat step 9 looking at ring of headphone output

23、 jack. TONE CONTROLS TEST 1)Set all large knobs to center (12 oclock), switches out, small knobs to 0. 2)Set scope-B to 1V/cm and 2ms/cm. 3)Set oscillator to 100Hz square wave at 46dBV. 4)Look at output, compare to Fig. 1. 5)One at a time, turn tone control knobs and compare output to figures (reset

24、ting each to center after finishing): A)Treble to 10- Fig. 2; Treble to 0- Fig. 3. B)Hi-mid freq. and level to 10- Fig. 4. C)Hi-mid to 0, level 10- Fig. 5. D)Hi-mid to 0, freq. on 0- Fig. 6. E)Lo-mid freq. and level to 10- Fig. 7. F)Lo- mid freq. to 0, level on 10- Fig. 8. G)Lo-mid level to 0, freq.

25、 on 0- Fig. 9. H)Bass to 10- Fig. 10; Bass to 0- Fig. 11. VOICING FILTERS TEST 1)Engage low-cut switch- compare to Fig. 12. Disengage. 2)Increase contour to 10- compare to Fig. 13. Turn to 0. 3)Increase hi-boost to 10- compare to Fig. 14. Turn to 0. BOOST / CHORUS / BALANCED OUTPUTS TEST 1)Increase

26、boost to 10- compare to Fig. 15. Turn to 0. 2)Change scope trigger to A and scope-A to 0.1V/cm range. 3)Look at direct out (J4) pins 2,3 - compare to Fig. 16. 4)Engage chorus switch with rate and depth to 0. 5)Look at balance out-R(J3) pin 3 (center), compare to Fig. 17. 6)It should have a small spi

27、ke that moves back and forth approx. 1 division every 2-3 seconds. 7)Increase rate to max. and spike travel should speed up to about once every .7 seconds. Rate to 0. 8)Increase depth to max. and the spike should travel back and forth about 5 divisions. Depth to 0. 9)Look at balance out-R pin 2(left

28、). Spike should be slightly smaller than that in Fig. 17. 10) Engage 1-2 switch (S5)- J3 pin 3 changes, J3 pin 2 stays the same. 11) Compare balance out-L(J4) pins 2-3 to Fig. 17. FOOTSWITCH TEST 1)Set scope-B to 2V/cm, trigger to B. 2)Connect RF2 to footswitch jack (J8) using stereo cord. 3)Set boo

29、st to max and chorus switch in on front panel. 4)Set RF2 switches so LEDs are off - compare to Fig. 1. 5)Engage boost switch. Boost LED should light on footswitch. 6)Compare output to Fig. 15. Disengage boost switch. 7)Engage chorus switch. LED should light on RF2 and on front panel. 8)Compare outpu

30、t to Fig. 18. Disengage chorus switch. 9)Remove footswitch, set boost to 0. Downloaded from www.M manuals search engine RETURN AND STEREO AUX IN TEST 1)Set AC-VM to 10V scale. 2)Set oscillator to 100 sine wave at 26dBV (50mV). 3)Insert plug from oscillator into return jack (J6). 4)Set output to 10.

31、Output = 2Vrms. 5)Insert plug from oscillator half-way into stereo aux. in jack (J5). Output = 3.5Vrms. 6)Push plug in rest of way. Output should be same as above. NOISE TEST 1)Remove oscillator input. 2)Turn large knobs to 10, small knobs to 0, switches out. 3)Connect speaker to output, listen for

32、noise. It should be clean with no crackling or distortion. 4)Change AC-VM range to 0.1V. 5)Noise should measure less than 30mV. 6)Engage low-cut, hi-boost and contour to 10. Noise 150mVrms. 7)Voicing filters off or to 0, boost to 10, chorus on. 8)Noise 200mVrms. RETURN KNOBS TO ZERO- READY FOR BURN-

33、IN Downloaded from www.M manuals search engine Downloaded from www.M manuals search engine Downloaded from www.M manuals search engine Downloaded from www.M manuals search engine Downloaded from www.M manuals search engine Downloaded from www.M manuals search engine Downloaded from www.M manuals search engine Downloaded from www.M manuals search engine