IC-R8600_user.pdf

《IC-R8600_user.pdf》由会员分享，可在线阅读，更多相关《IC-R8600_user.pdf（96页珍藏版）》请在收音机爱好者资料库上搜索。

1、INSTRUCTION MANUAL iR8600 COMMUNICATIONS RECEIVER i WORDDEFINITION R DANGER! Personal death, serious injury or an explosion may occur. R WARNING! Personal injury, fi re hazard or electric shock may occur. CAUTIONEquipment damage may occur. NOTE Recommended for optimum use. No risk of personal injury

2、, fi re or electric shock. EXPLICIT DEFINITIONS IMPORTANT READ ALL INSTRUCTIONS carefully completely before using the receiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains operating instructions for the IC-R8600. PREFACE Thank you for choosing this Icom product. The IC- R8600 COMMU

3、NICATIONS RECEIVER is a wide band receiver which designed to cover the 10 kHz to 3 GHz range with Icoms state of the SDR technology. With proper care, this product should provide you with years of trouble-free operation. Many hours of research and development went into the design of your IC-R8600. T

4、his product includes RTOS “RTX” software, and is licensed according to the software license. This product includes “zlib” open source software, and is licensed according to the open source software license. This product includes “libpng” open source software, and is licensed according to the open so

5、urce software license. Refer to page I for information on the open source software being used by this product. TRADEMARKS Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australi

6、a, New Zealand and/or other countries. NXDN is a trademark of Icom Incorporated and JVC KENWOOD Corporation. dPMR and the dPMR logo are trademarks of the dPMR MoU Association. Microsoft, Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States and/or other co

7、untries. All other products or brands are registered trademarks or trademarks of their respective holders. Hereby, Icom Inc. declares that the versions of IC-R8600 which have the “CE” symbol on the product, comply with the essential requirements of the Radio Equipment Directive, 2014/53/EU, and the

8、restriction of the use of certain hazardous substances in electrical and electronic equipment Directive, 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: http:/www.icom.co.jp/world/support/ ii While ordinary wide band receivers need to hav

9、e dedicated demodulator circuits for each receive mode, the IC- R8600 utilizes advanced digital processes that demodulate the incoming signals. The IF signal is sent to the A/D converter, resulting in digital signal, then is processed by a high-speed FPGA and DSP to be restored to an analog audio si

10、gnal. The received signal is processed to be demodulated according to the receive mode, including not only conventional analog communications in CW, AM, SSB, FM, WFM and FSK, but also advanced digital communications in D-STAR, P25, NXDN, dPMR and DCR. This was archived by using Software Defjned Radi

11、o (SDR) technology. The AMBE+2 voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipme

12、nt. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,36

13、5, #5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166. FEATURES Covers 10 kHz to 3 GHz for wide band reception Receives various digital modes such as D-STAR, P25 (Phase 1), NXDN, dPMR and DCR (Digital Convenience Radio) 12 kHz IF output port for DRM bro

14、adcast Hi-speed Real-Time Spectrum Scope A 4.3 inch touch panel color display Multi-function dials for easy settings An SD card slot You can record the received audio, save the receiver settings, decoded FSK logs and so on, onto an SD card (user supplied). “IP+” Function The IP Plus function improve

15、s 3rd order intercept point (IP3) performance. I/Q baseband signal output port Optional external speaker (with integrated power supply) SUPPLIED ACCESSORIES ABOUT THE SDR WIDEBAND RECEIVER CIRCUITS VOICE CODING TECHNOLOGY L Different types of accessories may be supplied, or may not be supplied depen

16、ding on the receiver version. DC power cable (3 m: 9.8 ft) Spare fuse (3 A/32 V) Spare fuse (3 A/125 V) Speaker plugs (3.5 mm: 1/8 Stereo) RCA plugs DC power short connector FPGABPFBPFA/DDSPD/A 1st LO2nd LO IF Demodulator Double conversion super heterodyne receiver (Example for 30.000000 MHz 1099.99

17、9999 MHz) iii FOR CLASS B UNINTENTIONAL RADIATORS: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installat

18、ion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this

19、 equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separ

20、ation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. DISPOSAL The crossed-out wheeled-bin symbol on your product, literature, or packaging

21、 reminds you that in the European Union, all electrical and electronic products, batteries, and accumulators (rechargeable batteries) must be taken to designated collection locations at the end of their work- ing life. Do not dispose of these products as unsorted municipal waste. Dispose of them acc

22、ording to the laws in your area. FCC INFORMATION WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. CAUTION: Changes or modifjcations to this device, not expressly approved by Icom Inc., could void your authority to

23、operate this device under FCC regulations. Icom is not responsible for the destruction, damage to, or performance of any Icom or non-Icom equipment, if the malfunction is because of: Force majeure, including, but not limited to, fjres, earthquakes, storms, fmoods, lightning, or other natural disaste

24、rs, disturbances, riots, war, or radioactive contamination. The use of Icom receivers with any equipment that is not manufactured or approved by Icom. iv DAbout the touch operation In the manual, the touch operation is described as shown below. Touch If the display is touched briefmy, one short beep

25、 sounds. Touch for 1 second If the display is touched for 1 second, one short and one long beep sound. DTouch screen precautions The touch screen may not properly work when the LCD protection fjlm or sheet is attached. Touching the screen with your fjnger nails, sharp topped object and so on, or tou

26、ching the screen hard may damage it. Tablet PCs operations such as fmick, pinch in and pinch out cannot be performed on this touch screen. DTouch screen maintenance If the touch screen becomes dusty or dirty, wipe it clean with a soft, dry cloth. When you wipe the touch screen, be careful not to pus

27、h it too hard or scratch it with your fjnger nails. Otherwise you may damage the screen. ABOUT THE INSTRUCTIONS Instruction example MENU SET Time Set Date Detailed instruction 1. Push MENU. Push The MENU screen opens. 2. Touch SET. MENU screen The SET screen opens. 3. Rotate to select “Time Set,” an

28、d then push . 4. Rotate to select “Date,” then push . SET screen This manual is described in the following manner. “ ” (Quotation marks): Used to indicate icons, setting items, and screen titles displayed on the screen. The screen titles are also indicated in uppercase letters. (Example: FUNCTION sc

29、reen) (brackets): Used to indicate keys. Routes to the set modes and setting screens Routes to the Set mode, setting screen and the setting items are described in the following manner. DATE/TIME screen DATE screen 5. Touch + or to set the date. 6. Touch SET to save the entry. v TABLE OF CONTENTS PRE

30、FACE . i IMPORTANT . i TRADEMARKS . i EXPLICIT DEFINITIONS . i FEATURES .ii ABOUT THE SDR WIDEBAND RECEIVER CIRCUITS .ii VOICE CODING TECHNOLOGY .ii SUPPLIED ACCESSORIES .ii FCC INFORMATION .iii ABOUT THE INSTRUCTIONS .iv DAbout the touch operation .iv DTouch screen precautions .iv DTouch screen mai

31、ntenance .iv TABLE OF CONTENTS . v PRECAUTIONS .viii 1 PANEL DESCRIPTION .1-1 Front panel .1-1 Rear panel .1-3 Touch panel display .1-4 DMULTI DIAL MENU () .1-6 DMULTI DIAL MENU () .1-6 DMULTI DIAL MENU () .1-6 DMENU screen .1-6 DQUICK MENU .1-6 DFUNCTION screen .1-7 DFUNCTION items .1-7 Keyboard en

32、tering and editing .1-7 DEntering and editing characters .1-7 DKeyboard types .1-8 DEntry example .1-8 2 INSTALLATION AND CONNECTIONS .2-1 Selecting a location .2-1 Heat dissipation .2-1 For desktop use .2-1 Grounding .2-1 Connecting a DC power supply .2-1 DPower supply .2-1 DTurning the receivers p

33、ower ON or OFF .2-1 Connecting an antenna .2-2 FSK (RTTY) connections .2-2 External device connection .2-3 3 BASIC OPERATION .3-1 Adjusting the volume level .3-1 RF gain/SQL level/Audio tone .3-1 DNoise squelch .3-1 DS-meter squelch .3-1 DRF gain .3-1 Monitor function .3-1 About the VFO and Memory m

34、odes .3-1 Selecting the receiving mode .3-1 Selecting the receiving mode (continued) .3-2 Setting the frequency .3-2 DDirectly entering a frequency .3-2 Changing the Tuning Step .3-2 DAbout the Tuning Step (TS) function .3-2 D About the Programmable Tuning Step function .3-3 DAbout the Auto Tuning S

35、tep function .3-3 Selecting the antenna .3-3 Dial/Panel Lock function .3-3 DDial Lock function .3-3 DPanel Lock function .3-3 Adjusting Backlight dimmer .3-4 Fine tuning .3-4 DWhen receiving FM, WFM or DIGITAL signal .3-4 DWhen receiving FSK signal .3-4 Selecting meter display .3-4 DMeter display ty

36、pes .3-4 4 SCOPE OPERATION .4-1 Spectrum scope screen .4-1 DRX Marker .4-1 DUsing the Spectrum Scope .4-1 DSetting the span .4-2 DSetting the range .4-2 DSearching for the peak signal .4-3 DTouch screen operation .4-3 DMini scope screen .4-3 DAdjusting the Reference level .4-4 DSweep speed.4-4 DScop

37、e set screen.4-5 5 OTHER FUNCTIONS .5-1 About the Function screen .5-1 Preamplifjer .5-1 Attenuator .5-1 Selecting the antenna .5-1 AGC function control .5-1 IP Plus function .5-2 Notch Filter .5-2 DSetting the notching width and frequency .5-2 Using the Digital Twin PBT .5-2 Selecting the digital I

38、F fjlter .5-3 DAdjusting the passband width .5-3 DSelecting the fjlter shape .5-3 Noise Blanker (NB) .5-4 Noise Reduction .5-4 Duplex operation .5-4 AFC function .5-5 Receiving in the CW mode .5-5 DSetting the CW pitch control .5-5 DAbout the CW Reverse mode.5-5 Receiving FSK (RTTY) signal .5-5 DDecoded FSK data display .5-5 DDecoding FSK signal