Team_PT-3208S_user.pdf

《Team_PT-3208S_user.pdf》由会员分享，可在线阅读，更多相关《Team_PT-3208S_user.pdf（15页珍藏版）》请在收音机爱好者资料库上搜索。

1、TEAM PT3208S electronic Bedienungsanleitung Manual Mode demploi PMR- 5 kHz Kanalabstand:schmal: 12,5 kHz / breit: 25 kHz Sendeleistung: max. 4 W Modulationsart:FM Frequenzhub:schmal: 2,5 kHz / breit: 5 kHz RX-Empfindlichkeit:schmal: +14 dBV/m bei 12,5 kHz / breit: +8 dBV/m bei 25 kHz NF-Ausgangsleis

2、tung:0.56 W an 8 bei 10 % THD Betriebsspannung:5,5 7,5 V Stromaufnahme:TX ( Low ): 490 mA; TX ( High ): 1,5 A RX ohne Stromsparschaltung: 60 mA RX mit Stromsparschaltung: 30 mA Abmessungen ohne berragende Teile:B/H/T: 59 x 117 x 42 mm Gewicht mit Batterien und Antenne:322 g Dieses Produkt ist bestim

3、mt fr die Inverkehrbringung und Benutzung in folgenden Lndern: Deutschland, sterreich und die Schweiz 10 DEUTSCH 11 ENGLISH 6)Programmierte Funktionen Hier tragen Sie die von Ihrem Hndler programmierten Funktionen ein. Bedingung der Fortsetzung des Kanalsuchlaufs berKanalsuchlauf Zeitsteuerung Signa

4、lsteuerungaktivinaktiv Dauer s Sendekanal whrend des KanalsuchlaufsSendezeitbegrenzung Erster KanalErster Kanal oder VorrangkanalVorrangkanal oder Dauer min aktueller Kanalaktueller Kanal Funktion der Monitor-Taste Keine Kurzzeitiges ffnen derffnen und SchlieenKurzzeitiges ffnen von FunktionCTCSS- u

5、nd DQT-der CTCSS- und DQT-Rauschsperre, CTCSS- StummschaltungStummschaltungund DQT-Stummschaltung TEAM PT-3208S Manual Table of Contents page Displays and Controls2 Setting Up the TEAM PT-3208S 12 Mounting of the Accumulator12 Mounting and Removing of the Belt Clip12 Operation of the TEAM PT-3208S13

6、 1)Turning the Unit On/Off13 2)Volume Level Adjustment13 3)Channel Selection13 4)Transmission13 5)Reception13 6)Sockets for External Speaker-Microphone14 7)Charging of the Accumulator14 8)Low Power Indicator14 Scan Function of the TEAM PT-3208S14 1)Start of Scan Function15 2)End of Scan Function15 3

7、)Restart of the Scan Function15 4)Transmission during activated Scan Function15 Auxiliary Functions of the TEAM PT-3208S15 1)Transmit Time Limiter 15 2)Busy Channel Lockout Function 16 3)Energy Saving Function16 4)Additional Muting Function16 General17 1)Safety17 2)Service17 3)Conformity17 4) Progra

8、mmed Channels17 5)Programmed Functions17 - 18 6)Technical Data18 7)CTCSS-Tones and DQT-Codes27 Setting up the TEAM PT-3208S Unpack carefully your UHF radio PT-3208S. Please check whether the supplied material mat- ches with the positions listed below. In case of loss or damage of a part contact your

9、 carrier at once. This transceiver is a heavy duty PMR radio, which can be optionally modified by your dealer also into a professional transceiver together with the PMR channels. In this unit only the channels 1 8 are already factory-preset to the PMR channels, i.e. the number of the rotary channel

10、selector position corresponds with the actual PMR channel. The positions 9 16 are free according to the factory setting. The TX output power on the PMR channels is reduced to 500 mW in the radiated field according to the European regulation. See in the chapter “technical data“ for the table of the P

11、MR channel numbers together with the corresponding frequencies. When the unit remains in pure PMR operation, it is free of charge and registration in most European countries. If you want to use the unit as a professional transceiver, you have to contact your local tele- communication authorities. Yo

12、u may be required to pay costs of registrations and annual fees for every unit and for every frequency. If your application is passed, you can go to your dealer and let him set your PT-3208S to the permitted frequency(ies) and adjustments. Mounting of the Accumulator At first turn the rear panel tow

13、ards you. Place the accumulator ( 9 ) in that way on the units rear panel that the 4 slip planes of the unit grip into the correspond- ing guiding slots of the accumulator, and that the accumulators charging contacts show into the direction of the units base. Then push the accumulator under simultan

14、eous slight pressure on its back into the direction of the units top side, until the latch on the units base clicks into place. Now the unit is ready for radio operation. Detaching of the Accumulator Turn again the units rear panel towards you. To release the accumulator from the unit you have to pu

15、ll the latch on the units base with your finger towards the units front panel, while pushing simultaneously the accumulator towards the units base. After the accumulator is slid out of the units slip planes you can take it off. Removing and mounting of the belt clip Turn the rear panel towards you.

16、Mounting of the Belt Clip Pull the springy support of the belt clip a bit out of its rest position by using your index finger and your middle finger. When the support is parallel to belt clips main part insert it from above into the corresponding guide on the back of the accumu- lator. Push the belt

17、 clip into the direction of the units base until the belt clips latch clicks into place. Detaching The latch of the belt clip is located on the accumulators back near the top side. Pull the latch with your fingernail away from the accumulators back and push simultaneously the belt clip towards the u

18、nits top side. After the belt clip is slid out of its guide you can take it off. battery packbelt clipdesktop charger wrist loopadapter manual Declaration of Conformity 12 ENGLISH Operation of the TEAM PT-3208S 1) Turning the unit On/Off To turn on the unit rotate the volume control with ON/OFF swit

19、ch VOLUME/OFF ( 4 ) from its rest position clockwise until you hear a clicking sound. A short beep tone will be heard from the loudspeaker ( 8 ), which indicates that the unit is in reception mode. To switch off the unit rotate the volume control with ON/OFF switch VOLUME/OFF ( 4 ) counterclockwise

20、to the final stop OFF until you hear a clicking sound. This indicates that the unit is switched off now. 2) Volume level adjustment If a radio operator sends a message on the actual channel, you can hear it in the incorporated loudspeaker ( 8 ). If the actual channel is free, the loudspeaker will be

21、 silent. In this case you can produce a strong noise in the loudspeaker by pressing the monitor key ( 6 ). Adjust the volume control VOLUME/OFF ( 4 ) to a comfortable listening level. Turning the control clockwise will increase the volume level and turning it coun- terclockwise will reduce the volum

22、e level. 3) Channel selection The TEAM PT-3208S has maximal 16 channels available. To select another channel turn the rotary channel selector 1-15, S ( 3 ). According to the programming of the channels, which has been made by your dealer, the unit will call up those transmit and reception frequencie

23、s which correspond to the actual position 1 15 ( 16 ) of the rotary channel selector. Note: If the rotary channel selector is set to a not programmed position, you will hear a con- tinuous warning tone in the loudspeaker. 4) Transmission Do not transmit if the antenna ( 1 ) is not mounted. Check act

24、ivity on the actual channel. Do not send if someone talks on the actual channel. Only if the loudspeaker is silent and the control lamp ( 2 ) is dark, the channel is free. Press also the monitor key ( 6 ). There must be a noise if the channel is not occupied. To transmit depress and hold the PTT key

25、 ( 5 ). During transmission the control lamp ( 2 ) lights up red and the rotary channel selector is disabled. Hold the unit upright. The sensitivity of the built-in microphone is set for speaking at a distance of 2 inches. Speaking too loud will cause distortions and makes the signal difficult to un

26、derstand. On completion of the transmission re- lease the PTT key and the set will return to receive mode. Note: Radio operation is only possible with the counter operator at coinciding channels. 5)Receiving After being switched on, the unit is always in receiving mode, as long as it is not transmit

27、ting. When it does not find any signal on the actual channel, it would produce a disturbing noise in the loudspeaker ( 8 ). For this end the unit is equipped with a built-in noise suppression circuit ( squelch ) that mutes the receiver if there is no station on the actual channel. If there is any in

28、coming signal, the squelch will turn the loudspeaker on and cause the control lamp ( 2 ) simul- taneously to light up green. This indicates that the channel is occupied. Your dealer can adjust the squelch threshold. The squelch function can be disabled to hear also weak stations which are not strong

29、 enough for the squelch to turn the loudspeaker on ( monitor function ). Depress the monitor key ( 6 ). Now the noise suppression is shut off and the control lamp lights simultaneously up green. If there is no station on the actual channel you hear a noise in the spea- ker. To reactivate the squelch

30、 release the monitor key ( 6 ) again. Thus the squelch works again. The monitor key function can also be changed by your dealer. For further information see point 4 of the chapter “Auxiliary functions of the PT-3208S”. ENGLISH 13 6)Sockets for External Speaker-Microphone Behind the screw-fixed cover

31、 on top of the units right side you can find two jack sockets for stereo plugs 2,5/3,5 mm SPK/MIC ( 7 ). They serve for the connec- tion of a speaker-microphone with PTT function or for a separate microphone or a separate speaker. As already indicated on the cover, the upper socket is for the spea-

32、ker and the lower socket is for the microphone. The internal speaker and/or the inter- nal microphone will be switched off, if the socket for the corresponding external accessory is in use. 7)Charging of the Accumulator The accumulator is not charged in the factory. Therefore it must be charged befo

33、re it is used the first time. Insert the DC connector of the power cord coming from the adapter into the socket on the rear of the charging mould. Then connect the adapter with a wall outlet ( 230 V, 50 Hz ). Now insert the transceiver with mounted accumulator or only the accumulator it- self into t

34、he charging mould. The front panel must show into the direction of the push button, or the charging contacts to the rear. The red LED ( CHARGING ) on the charging mould lights up now, which indicates that the charging process has started. After approximately six hours the red LED turns off and the g

35、reen LED ( COMPLETION ) lights up. That means that now the accumulator is charged and the charging current is reduced. The charging process can be continued for 1 or 2 hours after the green LED has turned on, to take advantage of the entire capacity of the accumulator. But do not exceed the charging

36、 duration beyond this time, otherwise you will cause an overcharging which will reduce the accumulator capacity or shorten the accumulator life. Atoo frequent recharging of a partially discharged accumulator will also result in a reduction of its capacity. For this end the charging mould is equipped

37、 with a discharge function. To activate a previous discharging of a partially discharged accumulator insert the transceiver with mounted accumulator or only the accumulator itself into the charging mould. After the red LED has begun to light up, depress brief- ly the button on the charging mould. Th

38、is will cause the red LED to turn off and the yellow LED ( DISCHARGING ) to turn on. That means that the accumulator is discharged now. At the end of the discharge process the yellow LED turns off automatically and the red LED ( CHARGING ) lights up again. This indicated that the charging process ha

39、s started automati- cally. At the end of the charge process the red LED turns off and the green LED lights up again, which indicates that the accumulator is charged now. Never try to recharge alkaline cells or other accumulators than the supplied one with the charg- ing mould. 8)Accumulator Alert In

40、dication The unit is equipped with a accumulator level monitoring circuit which alerts you, when the stor- ed energy is nearly completely used up. If the accumulator voltage drops below a certain value in receiving mode, you will hear a warning tone in the speaker. If the accumulator voltage drops b

41、elow this value while transmitting, the control lamp ( 2 ) starts to flash red. After releasing the PTT key and pressing it once again now, the unit will not transmit any more. Now it is time to recharge the accumulator. Scan function of the TEAM PT-3208S The scan function must be installed into you

42、r transceiver by your dealer, before you can use it. If it is not installed, there is another channel available on position S ( = 16 ) of the rotary chan- nel selector. In the description below it is assumed that the scan function is active. Ask your dea- ler for more details. 14 ENGLISH 1) Start of

43、 the scan function When you turn the rotary channel selector on position S ( = 16 ) the unit runs through all chan- nels which your dealer has selected for the scan function ( scanning list ). If there is a radio operator signal on one channel which is strong enough to open the squelch, the scan fun

44、ction will pause on that channel. You can hear the partner station but the scan remains active. 2) End of the scan function When you turn the rotary channel selector on a position between 1 and 15 the scan function is not active. 3) Restart of the scan function Your dealer can select between two con

45、ditions under which the scan function restarts stepping through the scanning list when it has previously stopped on an occupied channel: a) Time control: The scan function restarts working after a dealer-set dwell time between 0.5 and 5 s, beginning from the moment of stopping on that channel. The d

46、well time does not depend on whether the channel is free or still occupied. b) Carrier wave control: The scan function restarts working 3 s after the radio operator signal has dropped below the squelch threshold. 4) Transmission during activated scan function Your dealer can select one of 4 differen

47、t criteria to determine the transmit frequency while the scan function is active: a) First channel: When pressing the PTT key while the scan function is active the unit transmits basically on the first channel on the scanning list, i.e. the channel with the lowest channel num- ber. b) First channel

48、or actual channel: When the pressing of the PTT key occurs while the scan fun- ction is stepping through the scanning list, the unit transmits on the first channel on the scanning list. When the pressing of the PTT key occurs while the scan function is resting on a channel, the unit transmits on thi

49、s channel. c) Prior channel: When pressing the PTT key while the scan function is active the unit transmits basically on the prior channel, i.e. any channel of the scanning list which your dealer can select. d) Prior channel or actual channel: When the pressing of the PTT key occurs while the scan func- tion is stepping through the scanning list, the unit transmits on the prior channel. When the pres- sing of the PTT key occurs while the scan function is resting on a channel, the unit transmits on this channel. Note: Once a channel is selected for tran