Vertex_VX-2100_VX-2200_series_user.pdf

《Vertex_VX-2100_VX-2200_series_user.pdf》由会员分享，可在线阅读，更多相关《Vertex_VX-2100_VX-2200_series_user.pdf（24页珍藏版）》请在收音机爱好者资料库上搜索。

1、VX-2100 VX-2200 OPERATING MANUAL VX-2100 VX-2200 Vertex Standard LMR, Inc. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan Congratulations! You now have at your fingertips a valuable communications tool: a Vertex Standard two-way radio! Rugged, reliable and easy to use, your Vertex Standard radio

2、 will keep you in constant touch with your colleagues for years to come, with negligible main- tenance downtime. Please take a few minutes to read this manual carefully. The information presented here will allow you to derive maximum performance from your radio, in case ques- tions arise later on. W

3、ere glad you joined the Vertex Standard team. Call on us anytime, because commu- nications is our business. Let us help you get your message across. SAFETY/WARNING INFORMATION WARNING - DO NOT operate the VX-2100/-2200 radio when any person(s) (bystanders) outside the vehicle are within the distance

4、s shown in the chart at the bottom of this section. Safety Training information: Antennas used for this transmitter must not exceed an antenna gain of 0 dBd. The radio must be used in vehicle-mount configurations with a maximum oper- ating duty factor not exceeding 50 %, in typical Push-to-Talk conf

5、igurations. This radio is restricted to occupational use, work related operations only where the radio operator must have the knowledge to control the exposure conditions of its passengers and bystanders by maintaining the minimum separation distance shown below. Antenna Installation: For rear deck

6、trunk installation, the antenna must be located at least the following distance away from rear-seat passengers. For roof top installations, the antenna must be placed in the center of the roof. Unsafe Radiation Distance Warning! The 70.7 V RF voltage (45/50 W/50 ) or 50.0 V RF voltage (25 W/50 ) is

7、applied to the antenna terminal of the transciver while transmitting. Do not touch the TX RF section absolutely while transmitting. Caution: The radio can become hot. Do not operate the radio continuously in transmission mode for longer than 7 minutes. Ensure enough standby/reception time for cool-d

8、own between trans- mission periods. Be sure that TOT timer is correctly installed and properly working. Avoid touching the rear bottom of the transceivers body while trans- mission. VHF Model 3.3 Feet (1 m) 4.6 Feet (1.4 m) UHF Model 2.6 Feet (0.8 m) 3.9 Feet (1.2 m) 25 W 45/50 W VX-2100/-2200 SERIE

9、S OPERATING MANUAL1 INTRODUCTION The VX-2100/-2200 Series are full-featured FM transceivers designed for flexible mobile and base station business communications in the VHF or UHF Land Mobile bands. These transceiver are designed for reliable business communications in a wide variety of applications

10、 with a wide range of operating capability provided by their leading-edge design. The VX-2100 allows up to 8-channel memories. The VX-2200 allows up to 128- channel memories which can each be programmed with an 8-character channel name. Important channel frequency data is stored in EEPROM and flash

11、memory on the CPU, and is easily programmable by dealers using a personal computer and the Vertex Standard Programming Cable and CE82 Software. The pages which follow will detail the many advanced features provided on the VX- 2100/-2200 Series transceiver. After reading this manual, you may wish to

12、consult with your Network Administrator regarding precise details of the configuration of this equipment for use in your application. FOR NORTH AMERICAN USERS REGARDING 406 MHZ GUARD BAND The U.S. Coast Guard and National Oceanographic and Atmospheric Ad- ministration have requested the cooperation

13、of the U.S. Federal Communica- tions Commission in preserving the integrity of the protected frequency range 406.0 to 406.1 MHz, which is reserved for use by distress beacons. Do not attempt to program this apparatus, under any circumstances, for operation in the frequency range 406.0 - 406.1 MHz if

14、 the apparatus is to be used in or near North America. VX-2100 VX-2200 VX-2100/-2200 SERIES OPERATING MANUAL2 CONTROLS the red “TX” indicator will disappear and transmission will cease soon thereafter. To resume trans- mitting, you must release the PTT switch and wait for the “penalty timer” to expi

15、re (if you press the PTT switch before this timer expires, the timer restarts, and you will have to wait another “penalty” period) Key Lock In order to prevent accidental frequency change or inadvertent transmission, various aspects of the transceivers keys may be locked out. To activate the Locking

16、 feature, press and hold in the P1 key while turning the radio on. To disable the Locking feature, repeat this power-on procedure. ADVANCED OPERATION Programmable Function (PF) Buttons The VX-2100/-2200 Series includes six Programmable Function (PF) Buttons. The PF button functions can be customized

17、, via programming by your Vertex Standard dealer, to meet your communications/network requirements. Some features may re- quire the purchase and installation of optional internal accessories. The possible PF button programming features are illustrated below, and these functions are explained on the

18、pages to follow. For further details, contact your Vertex Standard dealer. For future reference, check the box next to the function that has been assigned to each PF button on your particular radio, and keep it handy. BASIC OPERATION OF THE TRANSCEIVER VX-2100/-2200 SERIES OPERATING MANUAL9 ?1: Thes

19、e functions cannot assign to VX-2100 ?2: Requires optional unit PF Button (PRESS KEY/PRESS AND HOLD KEY) Function MONI SQL OFF SQL SET DIMMER Channel Up Channel Down Continuous Ch Up Continuous Ch Down Group Up ?1 Group Down ?1 SCAN SCAN SET Group SCAN ?1 Group SCAN SET ?1 DW (Dual Watch) Follow-Me

20、SCAN Follow-Me DW LOW TA (Talk Around) TA SCAN Encryption ?2 Emergency RESET CALL 1 CALL 2 CALL 3 DTMF CODE SET ?1 Code Up ?1 Code Down ?1 Code SET ?1 Speed Dial ?1 Public Address EXT. ACC1 EXT. ACC2 Direct CH#1 Direct CH#2 AF Min Vr Lone Worker HA (Horn Alert) Key Lock SET ?1 P1 / / / / / / -/- -/-

21、 / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / P2 / / / / / / -/- -/- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / P3 / / / / / / -/- -/- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / P4 / / / / / / -/- -/- / / / / / / / / / / / / / / / /

22、/ / / / / / / / / / / / / / / / / ? / / / / / / -/- -/- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / ? / / / / / / -/- -/- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / ADVANCED OPERATION VX-2100/-2200 SERIES OPERATING MANUAL10 Description of Operating Functi

23、ons MONITOR (MONI) Press (or press and hold) the assigned programmable key to cancel CTCSS- and DCS-controlled squelch; the TX/BUSY indicator will glow green SQUELCH (SQL) OFF Press (or press and hold) the assigned programmable key to open the SQL to hear background noise (unmute the audio); the TX/

24、BUSY indicator will blink green. SQUELCH (SQL) SET You can manually adjust the squelch level using this function: ?Press (or press and hold) the assigned programmable key. A tone will sound, and the current squelch will level appears on the display. ?Press the ?/? button to select the desired squelc

25、h level. ?Press this key again. A tone will sound, and the display will revert to the normal channel indication. DIMMER Press (or press and hold) the assigned programmable key to select the brightness level of the display. Available selections are four levels. CHANNEL UP/DOWN Press (or press and hol

26、d) the assigned programmable key (generally the ?/? button) to select a different channel within the current group. CC UP/DOWN (CONTINUOUS CH UP/DOWN) Press and holding in the assigned programmable key causes the radio to begin step- ping (repeatedly) upward or downward through the channels. GROUP U

27、P/DOWN (This function is only available in the VX-2200) Press (or press and hold) the assigned programmable key to select a different group of channels ADVANCED OPERATION VX-2100/-2200 SERIES OPERATING MANUAL11 ADVANCED OPERATION CHANNEL SCAN (SCAN) The Scanning feature is used to monitor multiple c

28、hannels programmed into the transceiver. While scanning, the transceiver will check each channel for the pres- ence of a signal, and will stop on a channel if a signal is present. To activate scanning: ?Press (or press and hold) the assigned programmable key to activate scanning on the current group

29、. ?The scanner will search the programmed channels, looking for active ones; it will pause each time it finds a channel on which someone is speaking. ?Press (or press and hold) the assigned programmable key again to disable scan- ning. Operation will revert to the programmed revert channel. Note: Yo

30、ur dealer may have programmed your radio to stay on one of the fol- lowing channels: ? Current channel (“Talk Back”) ? “Last Busy” channel ? “Priority” channel ? “Scan Start” channel SCAN SET Press (or press and hold) the assigned programmable key to delete the Current Memory channel from the Scanni

31、ng. In the VX-2100, when you delete a channel, the decimal point “.” will disappear from the Channel Number Indicator. To restore a particular channel to your scan- ning list, press (or press and hold) the assigned programmable key again; the deci- mal point “.” will appear on the Channel Number Ind

32、icator. In the VX-2200, when you delete a Group or channel, “- SKIP -” will appear on the LCD for one second after pressing the assigned programmable key. To restore a particular channel to your scanning list, press (or press and hold) the assigned pro- grammable key again; “-STOP-” will appear on t

33、he LCD for one second after press- ing the assigned programmable key. VX-2100/-2200 SERIES OPERATING MANUAL12 GROUP SCAN (This function is only available in the VX-2200) The Scanning feature is used to monitor multiple channels programmed into the transceiver. While scanning, the transceiver will ch

34、eck each channel of the pro- grammed group for the presence of the signal, and will stop on a channel if a signal is present. Press (or press and hold) the assigned programmable key to activate the scanning on the selected groups. GROUP SCAN SET (This function is only available in the VX-2200) You m

35、ay wish to have the Scanner pass through more than one Group during the scanning process (normally, scanning is performed within the current group only). To include the current Group in the scanning loop, press (or press and hold) the assigned programmable key. To remove a Group from Group Scan, pre

36、ss (or press and hold) the assigned programmable key again. DUAL WATCH (DW) The Dual Watch feature is similar to the SCAN feature, except that only two chan- nels are monitored: ? The current operating channel; and ? The Priority channel. To activate Dual Watch: ?Press (or press and hold) the assign

37、ed programmable key. ?The scanner will search the two channels; it will pause each time it finds a channel on which someone is speaking. To stop Dual Watch: ?Press (or press and hold) the assigned programmable key. ?Operation will revert to the “Dual Watch Start” channel. ADVANCED OPERATION VX-2100/

38、-2200 SERIES OPERATING MANUAL13 FOLLOW-ME SCAN “Follow-Me” Scan feature checks a User-assigned Priority Channel regularly as you scan the other channels. Thus, if only Channels 1, 3, and 5 (of the 8 available channels) are designated for “Scanning,” the user may nonetheless assign Channel 2 as the “

39、User-assigned” Priority Channel via the “Follow-Me” feature. To activate “Follow-Me” scanning, first select the channel you want to designate as the “User-Assigned Priority Channel” and press (or press and hold)the assigned programmable key. Then press (or press and hold) the Channel Up/Down key (ge

40、n- erally the ?/? button) to recall to the “Scanning Start” channel which has been programmed by your dealer to activate the scanner. When the scanner stops on an “Active” channel, the User-assigned Priority Channel will automatically be checked every few seconds; if activity is found on the User-as

41、signed Priority Channel, the radio will switch between it and the Dealer-Assigned Priority Channel, if any. FOLLOW-ME DUAL WATCH (DW) To set up a “Dual Watch” frequency pair using the “Follow-Me” feature, select a channel using the Channel Up/Down key (generally the ?/? button). Now press (or press

42、and hold) the assigned programmable key; pressing the assigned program- mable key locks the current channel as the User-assigned Priority Channel. Now press (or press and hold) the Channel Up/Down key to select another channel (not the “Scanning Start” channel). Your radio will now switch back-and-f

43、orth between the currently-selected channel and the User-assigned Priority Channel. During “Follow-Me” scanning (after you have pressed the key), you can set up the “Dual Watch” feature by pressing (or press and holding) the Channel Up/Down key to another channel. The radio will then scan back and f

44、orth between the original User-assigned Priority Channel and the newly-selected channel. The Priority Channel you have assigned (before pressing the key) will be retained in memory until you change it. LOW POWER (LOW) Press (or press and hold) the assigned programmable key to set the radios transmit

45、- ter to the “Low Power” mode. Press (or press and hold) the key again to return to “High Power” operation when in difficult terrain. In the VX-2200, when the radios transmitter is set to “Low Power” mode, the “” icon will be indicated on the display. ADVANCED OPERATION VX-2100/-2200 SERIES OPERATIN

46、G MANUAL14 TALK AROUND (TA) Press (or press and hold) the assigned programmable key to activate the Talk Around feature when you are operating on duplex channel systems (separate receive and transmit frequencies, utilizing a “repeater” station). The Talk Around feature allows you to bypass the repea

47、ter station and talk directly to a station that is nearby. This feature has no effect when you are operating on “simplex” channels, where the re- ceive and transmit frequencies are already the same. In the VX-2200, when the “TA” function is activated, the “” icon will be indi- cated on the display.

48、Note that your dealer may have mode provision for “Talk Around” channels by programming “repeater” and “Talk Around” frequencies on two adjacent channels. If so, the key may be used for one of the other Pre-Programmed Functions. TA SCAN The “TA SCAN” is one of “DW Scan” between Rx and Tx frequency.

49、It works the Rx channel as priority channel and the radio will always transmit on the Tx Channel if the PTT is pressed in the TA SCAN mode. Press (or press and hold) the assigned programmable key to activate/deactivate the TA SCAN feature. ENCRYPTION (OPTION) When the Voice Scrambler feature is enabled, press (or press and hold) the assigned programmable key to toggle the voice encryption on and off. In the VX-2200, when the Voice Scrambler feature is activated, the “” icon will be indicated on the display. EMERGENCY The VX-2100/-2200