Ranger_SS-158EDX_serv.pdf
《Ranger_SS-158EDX_serv.pdf》由会员分享,可在线阅读,更多相关《Ranger_SS-158EDX_serv.pdf(48页珍藏版)》请在收音机爱好者资料库上搜索。
1、Model SS158 EDX( )B( ) Service Manual SS-158EDX( )B( ) 1 TABLE OF CONTENTS PAGE CHAPTER 1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.0 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1 Transmitter .
2、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 CHAPTER 2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.0 Fron
3、t Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.2 Procedure to Receive And Transmit . 6 2.3 Receiving SSB Signals . 7 2.4 Alternate Microphone And Installation
4、. 9 CHAPTER 3 3.0 Introductor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.1 PLL CIRCUIT 12 3.2 RECEIVER CIRCUIT. 12 3.3 Transmitter Modulation Circuit. 12 3.4 Transmitter Amplifier Circuit 13 CHAPTER 4 4.0 REQUIRED TEST EQUIPMENT 15 4.1 ALIGNMENT PROCEDUR
5、ES 15 CHAPTER 5 5.0 PRECAUTIONS. 22 5.1 PERIODIC INSPECTION. 22 5.2 FUSE REPLACEMENT. 22 CHAPTER 6 23 6.0 PCB Layout SSB: 25watts PEP Carrier Emission -50 dB Spurious Emission -50 dB Audio Distortion 10% Frequency Response 300 to 2500 Hz Microphone Dynamic 1.2 RECEIVER Sensitivity for 10 dB (S+N)/N
6、CW/AM : 1.0 V ; SSB : 0.25 V Sensitivity for 20 dB (S+N)/N FM : 0.5 V Squelch Sensitivity 28W Spurious Emission Minimum. Balance Power Between CH1 A and CH40 L. SSB ALC Set radio to CH 1 BAND G USB TX mode. AF signal 30mV, 1 KHz to microphone. VR13 25 W SSB Carrier Balance Set radio to CH 1 BAND G U
7、SB TX mode. Set MIC GAIN fully counter-clockwise. Connect Oscilloscope to antenna connector. VR6 Spurious Emission to Minimum. AM TX High Power Set radio to CH 1 BAND G AM TX mode. Modulation Off. Set RF POWER fully clockwise. VR14 10 W AM TX Low Power Set RF POWER fully counterclockwise. VR18 1W0.5
8、W RF Power Meter Set radio to CH 1 BAND G AM TX mode. Set RF POWER fully clockwise. Set SWR/MOD/PWR Switch to PWR position. VR9 For a needle reading of “red-green” on TX PWR scale. AM Modulation Set radio to CH 1 BAND G AM TX mode. AF signal 30mV, 1 KHz to microphone. Set MIC Gain fully clockwise. V
9、R16 For a needle reading of 90% on the external modulation meter. FM Modulation Set radio to CH 40 BAND L FM TX mode. AF signal 30mV, 1 KHz to microphone. Set MIC Gain fully clockwise. VR5 For a needle reading of 4.8K on the external modulation meter. SWR Meter Set radio to CH 1 BAND G AM TX mode. C
10、onnect 100 Load to ANT Set S/RF/SWR/CAL Switch to SWR position VR1(SWR PCB) For a needle reading of 2 on the SWR scale. CW Set radio to CH 1 BAND G CW mode. CW Key on VR8 Audio Output 20020 mV 18 4.1.3 RECEIVER ALIGNMENT ITEM U.U.T. SETTING ADJUST POINT MEASUREMENT AM Sensitivity Set radio to CH 40
11、BAND F RX mode. Set RF GAIN Fully Clockwise. Set SQ Fully Counter Clockwise. Set VOL Control at 2 oclock. Set NB/ANL switch to OFF position. Set CLARIFIER Control to 12 oclock. Connect RF SG to antenna jack Frequency 26.955 MHz, 1uV. Mod 30%. L2,L3,L5,L6, L7,L8,L9,L10 Audio Output 2V S/N 10 dB. Set
12、radio to CH 40 L AM RX mode. RF SG setting 29.655 MHz. Set radio to CH 1 A AM RX mode. RF SG setting 24.265 MHz. L5,L6,L7 For Balance Between CH 1 A and CH 40 L. USB Sensitivity Set radio to CH40 BAND F USB RX mode. Set VOL Control Fully Clockwise. RF SG setting 26.956 MHz, 0.25uV. Mod off. L11,L12
13、Audio Output 2V S/N 10dB. LSB Sensitivity Set radio to CH40 BAND F LSB RX mode. Set VOL Control Fully Clockwise. RF SG setting 26.954 MHz, 0.25uV. Mod off. L11,L12 Audio Output 2V S/N 10dB. FM Sensitivity Set radio to CH40 BAND F FM RX mode. Set VOL Control Fully Clockwise. RF SG setting 26.955 MHz,
14、 1mV. Mod 3K. RF SG setting 26.955 MHz, 0.5uV. Mod 3K L4 Audio Output MAX 5V S/N 10dB. NB Adjust Set radio to CH 39 F AM RX mode RF SG setting 26.955 MHz, 1000uV. Mod off. Set NB/OFF switch to ON position. Connect Multi-meter to TP1 (D2 cathode). L1 DC Voltage to max. ( 2.0V ) AM Squelch Set radio t
15、o CH 40 BAND F AM RX mode. Set SQ Control Fully Clockwise. RF SG setting 26.955 MHz, 1mV. Mod 30%. VR4 Adjust very slowly until squelch just closes. SSB Squelch Set radio to CH 40 BAND F USB RX mode. Set SQ Control Fully Clockwise. RF SG setting 26.966 MHz, 1 mV. Mod off. VR3 Adjust very slowly unti
16、l squelch just closes 19 ITEM U.U.T. SETTING ADJUST POINT MEASUREMENT AM S-Meter Set radio to CH 40 BAND F AM RX mode. RF SG setting 26.955 MHz, 100uV. Mod 30%. VR1 For a reading of “9” on the “S” scale. SSB S-Meter Set radio to CH 19 USB RX mode. RF SG setting 26.966 MHz, 100uV. Mod off. VR2 For a
17、reading of “9” on the “S” scale - 20 - Figure 4.1.2 Transmitter test setup Figure 4.1.3 Receiver test setup - 21 - SS158EDX(B) MAIN PCB ADJUSTMENT LOCATION - 22 - CHAPTER 5 MAINTENANCE 5.0 PRECAUTIONS The inherent quality of the solid-state components used in this transceiver will provide many years
18、 of continuous use. Taking the following precautions will prevent damage to the transceiver. (i) Never key the transmitter unless an antenna or suitable dummy load is connected to the antenna receptacle. (ii) Ensure that the input voltage does not exceed 16 VDC or fall below 11. (iii) Transmitting o
19、ver long periods can cause heat built-up and cause transmitter damage. 5.1 PERIODIC INSPECTION This unit is aligned at the factory to deliver maximum performance. However, continued performance cannot be expected without periodic inspection and maintenance. Important points to be checked regularly a
20、re as follows; Check Item Action Whip antenna (option) If cracked or broken, replace it. Coaxial cable If sheath is cracked or immersed in water, install new coaxial cable. Coaxial & power plug connections If loosened, reconnect. If corroded, clean contacts. Battery connection If corroded, clean pow
21、er terminals. Ground terminal If corroded, clean terminal. 5.2 FUSE REPLACEMENT To protect the equipment from serious damage, a fuse is provided on the power supply lines. The fuse protects against over voltage / reverse polarity or internal fault of the equipment. If the fuse has blown, first find
22、out the cause of the trouble before replacing it. A fuse rated for more than the transceiver requirement should not be used, since it may permanently damage the equipment. Damage due to over fusing is not covered by the warranty. - 23 - CHAPTER 6 DIAGRAMS & PARTS LIST 6.0 GENERAL Information on most
23、 electrical and mechanical parts is included in the parts list. The reference designators are in alphanumeric order. - 24 - SS158 EDX(B) DISPLAY PCB (EPT900022Z) (COPPER SIDE) ( COMPONENT SIDE ) - 25 - PART LIST: SS158 EDX(B) DISPLAY P.C.B ITEM REFERENCE NUMBER RANGER PART NUMBER DESCRIPTION 1 EPT90
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Ranger_SS 158 EDX_serv
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


